Chalcogenide Glasses for Infrared Optics

  • 73 49 6
  • Like this paper and download? You can publish your own PDF file online for free in a few minutes! Sign Up

Chalcogenide Glasses for Infrared Optics

This page intentionally left blank Dr. A. Ray Hilton, Sr. Chairman of the Board and Technical Director Amorphous Ma

1,673 475 7MB

Pages 300 Page size 413.28 x 653.76 pts Year 2010

Report DMCA / Copyright

DOWNLOAD FILE

Recommend Papers

File loading please wait...
Citation preview

Chalcogenide Glasses for Infrared Optics

This page intentionally left blank

Chalcogenide Glasses for Infrared Optics Dr. A. Ray Hilton, Sr. Chairman of the Board and Technical Director Amorphous Materials, Inc. Garland, Texas

New York Chicago San Francisco Lisbon London Madrid Mexico City Milan New Delhi San Juan Seoul Singapore Sydney Toronto

Copyright © 2010 by The McGraw-Hill Companies, Inc. All rights reserved. Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of the publisher. ISBN:978-0-07-159698-5 MHID: 0-07-15969-8-4 The material in this eBook also appears in the print version of this title: ISBN: 978-0-07-159697-8, MHID: 0-07-159697-6. All trademarks are trademarks of their respective owners. Rather than put a trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to the benefit of the trademark owner, with no intention of infringement of the trademark. Where such designations appear in this book, they have been printed with initial caps. McGraw-Hill eBooks are available at special quantity discounts to use as premiums and sales promotions,or for use in corporate training programs. To contact a representative please e-mail us at [email protected]. Information contained in this work has been obtained by The McGraw-Hill Companies, Inc. (“McGrawHill”) from sources believed to be reliable. However, neither McGraw-Hill nor its authors guarantee the accuracy or completeness of any information published herein, and neither McGraw-Hill nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that McGraw-Hill and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistanceof an appropriate professional should be sought. TERMS OF USE This is a copyrighted work and The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and its licensors reserve all rights in and to the work. Use of this work is subject to these terms. Except as permitted under the Copyright Act of 1976 and the right to store and retrieve one copy of the work, you may not decompile, disassemble, reverse engineer, reproduce, modify, create derivative works based upon, transmit, distribute, disseminate, sell, publish or sublicense the work or any part of it without McGraw-Hill’s prior consent. You may use the work for your own noncommercial and personal use; any other use of the work is strictly prohibited. Your right to use the work may be terminated if you fail to comply with these terms. THE WORK IS PROVIDED “AS IS.” McGRAW-HILL AND ITS LICENSORS MAKE NO GUARANTEES OR WARRANTIES AS TO THE ACCURACY, ADEQUACY OR COMPLETENESS OF OR RESULTS TO BE OBTAINED FROM USING THE WORK, INCLUDING ANY INFORMATION THAT CAN BE ACCESSED THROUGH THE WORK VIA HYPERLINK OR OTHERWISE, AND EXPRESSLY DISCLAIM ANY WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. McGraw-Hill and its licensors do not warrant or guarantee that the functions contained in the work will meet your requirements or that its operation will be uninterrupted or error free. Neither McGraw-Hill nor its licensors shall be liable to you or anyone else for any inaccuracy, error or omission, regardless of cause, in the work or for any damages resulting therefrom. McGraw-Hill has no responsibility for the content of any information accessed through the work. Under no circumstances shall McGraw-Hill and/or its licensors be liable for any indirect, incidental, special, punitive, consequential or similar damages that result from the use of or inability to use the work, even if any of them has been advised of the possibility of such damages. This limitation of liability shall apply to any claim or cause whatsoever whether such claim or cause arises in contract, tort or otherwise.

About the Author Dr. A. Ray Hilton, Sr., is known worldwide through publications describing his efforts in chalcogenide glasses. He serves as Chairman of the Board and Technical Director of Amorphous Materials, Inc. (AMI). Under Dr. Hilton’s direction and guidance, a process was developed to compound and cast highpurity homogeneous plates of chalcogenide glasses carried out under high vacuum in high-purity quartz containers. Thousands of glass blanks required for government FLIR systems produced in the 1980s for the Army were supplied by AMI. AMI is currently developing new glass compositions for lenses for use in inexpensive infrared cameras.

This page intentionally left blank

Contents 1

2

Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

xi xv

Transmission of Light by Solids . . . . . . . . . . . . . . . . 1.1 Solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Beginning of Transmission of Light— An Electronic Transition ................ 1.3 Long-Wavelength Cutoff . . . . . . . . . . . . . . . . 1.4 Extrinsic Loss within the Band, Impurities, Scatter, and Quality . . . . . . . . . . . . . . . . . . . . . 1.5 Optical Constants and Dispersion due to Strong Absorption . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 1

Chalcogenide Glasses ........................ 2.1 Historical Development . . . . . . . . . . . . . . . . . 2.2 The Periodic Table and Glass Formation . . . 2.3 Evaluating Possible Glass Forming Systems . . . 2.4 Qualitative Evaluation of Compositions for Development . . . . . . . . . . . . . . . . . . . . . . . 2.5 General Physical Properties of Chalcogenide Glasses . . . . . . . . . . . . . . . . . . . 2.5.1 Softening Points and Hardness .... 2.5.2 Thermal Coefficients of Expansion . . . 2.5.3 Density . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.4 Molar Refraction . . . . . . . . . . . . . . . . . 2.5.5 Electrical Properties . . . . . . . . . . . . . . 2.5.6 Physical Strength . . . . . . . . . . . . . . . . . 2.5.7 Softening Points . . . . . . . . . . . . . . . . . . 2.6 Chemical Bonding in Chalcogenide Glasses . . . 2.6.1 Composition Location in the Glass Forming Diagram . . . . . . . . . . . 2.6.2 Molecular Vibrations of Constituent Atoms . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6.3 Mass Spectrometric Investigation of Bonding in the Glasses . . . . . . . . . 2.6.4 X-ray Radial Distribution Analysis of Chalcogenide Glasses ............ 2.6.5 Conclusions from the TI Exploratory Programs of 1962 to 1965 .........

2 5 10 12 14 17 17 21 29 35 40 40 41 41 42 47 47 48 48 48 50 55 57 59

vii

viii

Contents 2.7

Chalcogenide Glasses Containing Transition Elements . . . . . . . . . . . . . . . . . . . . . 2.8 Discussion of Results . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4

5

6

60 66 69

Glass Production . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Reactants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Compounding Methods . . . . . . . . . . . . . . . . . 3.3 Compounding with Reactant Purification . . . 3.4 Open Casting Methods . . . . . . . . . . . . . . . . . . 3.5 Purification, Compounding, Casting—One Closed Operation . . . . . . . . . . . . . . . . . . . . . . . 3.6 Summary ............................. References ............................

71 71 73 74 77

Characterization of Glass Properties . . . . . . . . . . . . 4.1 Thermal Expansion, Glass Transition Temperature, and Softening Point . . . . . . . . 4.2 Transmission, Precise Refractive Index, and Thermal Change in Refractive Index . . . . . . 4.3 Physical Properties Important for Optical Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 Hardness . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 Young’s Modulus, Shear Modulus, and Poisson’s Ratio .............. 4.3.3 Rupture Modulus . . . . . . . . . . . . . . . . 4.3.4 Thermal Conductivity . . . . . . . . . . . . 4.3.5 Electrical Resistance . . . . . . . . . . . . . . 4.4 Resistance to Chemical Attack . . . . . . . . . . . . 4.5 Final Production Procedure . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

89

109 110 112 113 114 114 118

Conventional Lens Fabrication and Spherical Surfaces ........................... 5.1 Lens Blank Preparation . . . . . . . . . . . . . . . . . . 5.2 Generation of Spherical Surfaces . . . . . . . . . 5.3 Polishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 Antireflection Coatings . . . . . . . . . . . . . . . . . . Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

119 119 121 122 123 126 129

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos . . . . . . . . . . . . . . . . . . 6.1 Optical Designs . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Diamond Turning . . . . . . . . . . . . . . . . . . . . . . 6.3 Slump Molding . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Precision Molding .....................

131 131 132 133 133

84 86 87

89 94 108 108

Contents 6.5 6.6

7

8

9

Volume Production . . . . . . . . . . . . . . . . . . . . . Problem of Refractive Index Change When Pressure Molding . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146

Glass Processes for Other Applications . . . . . . . . . 7.1 AMI as Supplier of Chalcogenide Glasses for IR Fibers . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 AMI Fiber Drawing Process . . . . . . . . . . . . . . 7.3 Chemical Applications of AMI IR Fiber . . . . 7.3.1 Fiber Summary . . . . . . . . . . . . . . . . . . 7.4 Extrusion of Chalcogenide Glasses . . . . . . . . 7.4.1 Glass Extrusion Summary . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

153

IR Imaging Bundles Made from Chalcogenide Glass Fibers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 The Stacked Ribbon Method . . . . . . . . . . . . . 8.2 IR Imaging Bundles of 1-m Length . . . . . . . . 8.3 Goals of the Navy SBIR 10-m IR Imaging Bundle Program . . . . . . . . . . . . . . . . . . . . . . . . 8.4 The Navy Phase II 27-Month Program .... 8.4.1 The 1-m C2 Imaging Bundles . . . . . . 8.4.2 AMI Glass Clad Fibers . . . . . . . . . . . . 8.4.3 AMI Production of High-Purity Arsenic Trisulfide Glass . . . . . . . . . . . 8.4.4 The 50 Percent Transmission Goal . . . 8.4.5 Formation of Bundles on the 10-m Drum ..................... 8.4.6 Optical Evaluation of 10-m Imaging Bundles . . . . . . . . . . . . . . . . . 8.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AMI Infrared Crystalline Materials . . . . . . . . . . . . . 9.1 Cadmium Telluride . . . . . . . . . . . . . . . . . . . . . 9.2 Previous Work at TI .................... 9.2.1 Conclusions Concerning This Effort . . 9.3 AMI DARPA-Funded Large Plate Process . . . 9.3.1 Conclusions . . . . . . . . . . . . . . . . . . . . . 9.4 Vacuum Float Zoned Silicon Detector Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5 Silicon as an Infrared Optical Material .... 9.6 Single-Crystal Silicon Fibers . . . . . . . . . . . . . 9.7 Gallium Arsenide as an Infrared Optical Material . . . . . . . . . . . . . . . . . . . . . . . .

148 151

153 158 168 173 174 178 178 181 181 184 191 192 192 194 194 196 199 204 209 210 211 211 212 214 215 221 222 225 228 230

ix

x

Contents 9.8 9.9

10

Production of GaAs at AMI . . . . . . . . . . . . . . Horizontal Bridgman Production of GaAs Plates at AMI . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

231

Early Work at Texas Instruments . . . . . . . . . . . . . . . 10.1 First Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Infrared Applications to Materials . . . . . . . . 10.3 Optical Interference and Film Thickness . . . 10.4 The Infrared Scan Technique for Epitaxial Film Thickness ........................ 10.5 Elliptical Polarization of Light on Reflection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6 Measuring the Elliptical Polarization Angles y and D . . . . . . . . . . . . . . . . . . . . . . . . . 10.7 Ellipsometers Used at TI . . . . . . . . . . . . . . . . . 10.8 Infrared Ellipsometry . . . . . . . . . . . . . . . . . . . 10.9 The TI Automatic Ellipsometer System . . . . 10.10 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

245 245 245 247

Index

271

.......................................

233 243

248 252 255 259 259 264 269 270

Acknowledgments

W

hen you read this book describing my 50 years’ experience, you will find the applied research process is not flawless. Bad choices and false starts I made are identified. But when it came to choosing with whom I was going to share my life, I was dead on. My wife, Madora Pauline Bull Hilton, of 58 years has been in my corner, on my side every step of the way, through the years in college, followed by service in the Air Force, and graduate school while raising three children on the G.I. Bill. A few people influenced me as I pursued this path in life. We had help from John Beckham, the business manager of the chemistry department, and I taught freshman labs under Dr. Tom Burkhalter and finally received a research fellowship via Dr. Albert Jache, my senior adviser, who also taught me the love of research. We finally finished in 1959, there was one more oil company job in Houston, and then it was off to a goodpaying job at Texas Instruments in Dallas in 1960. Texas Instruments was a great place to work. The colleagues who helped me most were Charlie Jones, Harold Hafner, and Dr. George Cronin. Technicians were Jimmie Parker and Joyce Jones. In 1974, after 14 years in the TI CRL, 5 years as a senior scientist, I left to manage the infrared glass production in the EO Division. The production of the glasses had become very important. I soon realized there was a need for a second source of the glass, a unique opportunity for me. Like many, I had always wanted to run my own company. In 1977 when I told Madora what I wanted to do, she said go ahead, since it has always been your dream. I will join the company, she said, but I will still need time to be with my children and grandchildren. So I left TI in March 1977, borrowed some money from a bank, using land we owned as collateral, and accepted stockholders. We started in a small rented building. Our first employee was Glen Whaley, a master glass blower from TI. His son, Greg Whaley, and our oldest son, Ray Hilton, Jr., worked part-time while still going to school. Glen’s friend Mitchell Jones was our first technician. Our oldest daughter, Gail Hanna, soon joined us as a technician followed by James McCord from TI. AMI has been in operation 32 years, and our son is now president. Greg Whaley is vice president and director

xi

xii

Acknowledgments for sales and contracts. Our daughter, Gail Hanna, is our antireflection coating specialist. Madora is retired and spends time with her 12 grandchildren, all of whom live here. I would also like to acknowledge the following individuals who contributed to the work reported in the designated chapter(s): Chapters Cam Allen, System Design, TI

10

Max Amon, Optical Design, LMCO

6

Dr. R. J. Archer, Ellipsometry, Hewlett-Packard

10

Dr. Werner Beyen, laboratory director, TI

10

Dr. Steve Boldish, AMI consultant

9

Maurice Brau, SC Materials, TI

2, 6

Max Bryant, Mass Spectrometry, TI

2

Dr. Tom Burkhalter, laboratory director, TI

10

Ed Carr, coatings consultant, AMI

5, 6, 8

Ron Child, glass blower, TI

10

Igeno Lombardo Codman, Johnson & Johnson

7

Dr. George Cronin, SC Materials, TI/AMI

7, 9

Gene Daniels, computer programmer, TI

10

Jim Davidson, Thermalscan

8

Dr. Robert Dobrot, X-ray Structure, TI

2

Gerald Ferguson, AMI Navy Representative

7

Dr. Jacob Fraden, Thermoscan

7

Carl Fritz, grandson, IR Refractometer, AMI

7

Dr. Tommy George, Mass Spectrometry, TI

2

Amy Graham, IR&D, LMCO

6

Harold Hafner, Glass Science, TI

3, 9

Dr. John Hall, Optical Design, NVL

9

Gail Hanna, daughter, coating technician, AMI

5, 6, 8

Bob Harp, senior technician, TI

9

Dr. Jim Harrington, professor, Rutgers University

7

Dr. Don Hayes, president, Micro Fab

3

Ray Hilton, Jr., president, AMI

3, 5–9

Bob Icovazzi, Optics Production, LMCO

9

Dr. Pete Johnson, Ceramics, TI

10

Acknowledgments

Charlie Jones, Materials, TI

2, 3, 9, 10

Dr. Eric Jones, Computer Science, TI

10

Mitchell Jones, senior technician, AMI

3, 9

Edward Knerr, IRAD program, LMCO

6

Dr. Heinz Krebs, professor, Stuttgart University

2

John Lawson, Optics Design, CBC America Optics

6

Rich LeBlanc, IR&D, LMCO, AMI director

6

Tom Loretz, Glass Science, AMI consultant

7, 8

Al Lyon, Optical Design, LMCO

9

James McCord, senior technician, AMI

3, 6–9

Dr. Peter Melling, president, Remspec

8

Paul Modlin, Advantek Engineering

8

Robert Patterson, TI 1173 Glass Composition

4

Charles Ratliff, Computer Science, TI

10

Dr. Mike Rechtin, Materials Science, TI

3

Dr. Allen Rineberg, Physics, TI

10

Dr. Grady Roberts, Materials Science, TI

2

Nate Rosebrooks, Sancliff Equipment

7

Dr. Laird Shearer, Physics, Lasers, TI

10

Doug Sinclair, senior technician, TI

10

Horace Spain, production engineer, Exxon

10

Dr. Larry Swink, X-ray Structure, TI/AMI

3

Jan Terlouw, vice president, CBC America Optics

6

William Thompson, consultant for optics, AMI

4, 6, 8

Ronald Timm, senior technician, AMI

6

Dale Welt, senior technician, AMI

9

Dub Westfall, senior technician, TI

10

Glen Whaley, vice president, AMI

3, 7–10

Dr. Donald Wierauch, TI 20 Glass Composition

2

Gary Wiese, Optical Design, LMCO

8

Dan Woody, IR&D, LMCO

6

xiii

This page intentionally left blank

Introduction

T

he purpose of this book is to describe the technology developed over 50 years to utilize chalcogenide glasses as infrared optical materials. Chalcogenide glasses are based on the chalcogen elements sulfur, selenium, and tellurium excluding oxygen, the first member of the family. The name is a misnomer since chalcogen is from the Greek meaning chalk former and oxygen is the only member of the family that forms chalk. All its compounds are called oxides. Methods used to identify qualitatively chalcogenide glass compositions with promise to become useful infrared optical materials are discussed. Once identified, the optical and related physical properties must be measured quantitatively. The method best suited for the production of homogeneous glass in high purity and quantity must then be developed. Thus, a great deal of effort is required before a glass composition is considered by optical designers ready for use in an infrared system. For this reason, only a few glass compositions have been fully developed and used in quantity over the years. Infrared light by definition is light with a wavelength greater than the sensitivity region of the human eye, 4000 to 8000 Å. For infrared discussions, the more commonly used terms are 0.4 to 0.8 µm with µm being the abbreviation for micrometers. Of special importance are materials useful for infrared imaging systems designed to respond to infrared energy transmitted through the atmosphere. Figure I.1 illustrates infrared light absorption in the air at sea level due to water vapor, carbon dioxide gas, and ozone. The bottom illustration is the resultant total for the three gas molecules. Notice there are two windows indicated where energy is transmitted well, from 3 to 5 µm (hot window) and about 7 to 14 µm (thermal window). The window is called thermal since the peak of emitted radiation from a body at room temperature, about 300 K, occurs in this window. Thermal imaging of a living subject is based on emitted radiation, which is transmitted in this atmospheric window. The hot window refers to the fact that heated objects emit at the shorter wavelengths in this range. Examples might be the tailpipe of a jetplane or a missile exhaust.

xv

xvi

Introduction

1

2

3

4

5

6

7

Wavelength 8 9 10 11 12 13 14 15 16 Water vapor

Relative absorption

Carbon dioxide

Ozone

Window

Window Primary atmospheric constituents

H2O H2O CO2

CO2

H2O

O3 CO2

H2O, CO2

FIGURE I.1 Infrared absorption bands of primary atmospheric constituents for average conditions at sea level.

Over the years, materials used in infrared systems have included alkali halides, alkaline earth halides, melt formed semiconductors, vapor grown fine-grain polycrystalline semiconductors, and chalcogenide glasses. Each of the crystal materials has some advantages and some disadvantages that will be discussed toward the end of this book. However, this book will concentrate chiefly on chalcogenide glasses. After 17 years at Texas Instruments (TI), the author left in 1977 to found Amorphous Materials (AMI), a small company dedicated to producing infrared transmitting glasses for use in infrared optical systems. The company is still active in developing new glass compositions for new applications. Some crystalline materials were produced at AMI. The production of vacuum float zoned silicon, gallium arsenide, and cadmium telluride, all useful in infrared technology, will be described. Most of the early glass work reported here was carried out at TI in governmentsponsored programs as indicated in the references. Discussions of glasses developed at AMI and their applications will be given. Some results of infrared techniques applied to semiconductors at TI will be

Introduction described. Glasses have a major advantage over crystalline materials in that they can be easily cast, molded, extruded, and drawn into fiber. Such processes generally cannot be applied to crystalline materials but were applied to chalcogenide glasses. Also, the composition of a glass can be changed within limits to enhance properties important to an application. Very little such latitude exists with crystals. The ratios among constituent atoms of most crystalline materials are fixed. Examples of how the composition of some glasses was changed at AMI to enhance a property will be discussed. Comments to the readers who are students: The author considers himself a physical chemist. Chemistry is an applied science and mostly empirical. Tools used while conducting a research project have changed immensely since 1948 when this author started out, from slide rules and burets to computers, infrared FTIR spectrophotometers, Raman instruments, electron microscopes, and differential thermal analysis (DTA) for glasses. Lasers were not even invented until 1959. There was no material sciences school, only chemistry and physics. Chemical structural theories have changed greatly based on results from the new instruments and techniques. The language of science is constantly changing, reflecting people’s increased understanding, which improves their descriptions. Not nature! Nature never changes. Avoid having a preconceived solution to a problem before you start. Let nature guide you through the results of your experiments. Always remember, it is the investigation that is important, not the investigator. It is not important to be right at the start—only at the finish.

xvii

This page intentionally left blank

Chalcogenide Glasses for Infrared Optics

This page intentionally left blank

CHAPTER

1

Transmission of Light by Solids 1.1

Solids In nature, material exists as gas, liquid, or solid. Gas atoms or molecules are free to move within the confines of their container. Liquids move to fill the shape of their container while solids are rigid in shape. There is about a 1000-fold increase in density in going from gas to the condensed state of liquid or solid. The atoms or molecules come much closer together as a liquid and closer still as a solid. The dense solid may have a precise three-dimensional spatial arrangement for the atoms making up the solid that covers thousands of neighbors in all three directions. When the long-range order is perfect, the solid may be referred to as single-crystal. Or the order may be maintained over limited atomic distances and be referred to as polycrystalline. The atoms or molecules of liquids are free to move within their arrangements continuously in any direction and are said to have no long-range three-dimensional order. Order found is that of nearest neighbors or second nearest neighbors or even more, but not long range in the structural sense. Depending on elemental composition, when the atoms or molecules of a solid come close together, they begin to share their electronic bonding states, which results in formation of an energy structure for the solid. When excited, bonding valence electrons are elevated into a higher conduction band state and are free to travel through the solid as charge if an electric field is applied. The energy difference between the valence state and the free conduction state is called the bandgap of the solid. The vacancies left in the valence band are called holes and can constitute charge flow moving in the opposite direction to the field. The band structure is well developed and precise in crystalline solids with good crystalline perfection. Liquids and amorphous solid glasses are condensed states but without long-range three-dimensional orders. A glass is referred to as a disordered solid. The energy band structure may exist, but the

1

2

Chapter One energy level states in the band structure are not nearly as precise as in a crystalline solid.

1.2

Beginning of Transmission of Light—An Electronic Transition Generally speaking, infrared optical materials are insulators or semiconductors as judged by their bandgaps and resistivity. Photons of light corresponding to energy greater than the bandgap of the solid are strongly absorbed at the surface. As the wavelength is increased and the photon energy decreased below the bandgap, light is transmitted through the solid. The beginning of light transmission of a solid occurs at the wavelength that corresponds to the bandgap energy. The absorption of the photon is a very strong, quantized electronic transition. One may think of this energy as representing the average ionization energy for the primary chemical bonds formed between the atoms that make up the solid. If the required ionization energy is large enough, transmission begins in the ultraviolet region of the spectrum, as in the case for alkali halides or alkaline earth halides. Then the solid appears water-clear or colorless. If it occurs in the visible region, the solid appears colored. If the absorption edge occurs in the infrared region, the solid appears metallic because all visible light is strongly absorbed and reflected. The use of infrared spectroscopy as an analytical tool to identify and measure concentrations of organic compounds began in the late 1940s. Instruments, crude by today’s standards, used salt prisms to disperse the light, salt windows for the instrument, and cells to contain the samples being analyzed. Petroleum refineries used the infraredbased technology for quality control in their laboratories. The bandgaps for both the alkali halides and the alkaline earth halides occur in the ultraviolet region and were not a factor in their infrared use. Most of these ionic solids are soft, weak, and hygroscopic, making them unsuitable for use outside of the laboratory. The semiconductor revolution began in the early 1950s at Bell Telephone Laboratories when Gordon Teal et al.1 developed the ability to grow high-purity germanium in single-crystal form. The result was the germanium transistor. Later in the 1950s, Gordon Teal joined Texas Instruments and under his direction accomplished the same feat for silicon, resulting in the silicon transistor. Both germanium and silicon found use as infrared optical materials and as infrared light detectors. Germanium windows and lenses became the optical material standard for the industry due to their wide transmission, 2 to 20 µm, with very little change in refractive index (low dispersion) and good physical properties. Silicon found use as a missile dome material due to its superior physical properties such as strength and hardness. The transmission range was 2 to 14 µm again with little

Tr a n s m i s s i o n o f L i g h t b y S o l i d s refractive index change and physical properties superior to those of germanium. However, silicon has a lattice absorption at 9 µm in the middle of the most desirable 8- to 14-µm atmospheric window. Generally, the bandgaps of semiconductors decrease with increasing atomic mass as illustrated in Fig. 1.1. The plots show the bandgaps for the group IV elements, the II–VI and III–V compound semiconductors as a function of their molecular weights. A similar relationship may be established for chalcogenide glasses. An average molecular weight for glasses may be calculated by multiplying the percentage of each constituent atom by its atomic mass and adding to get the total. The application of chalcogenide glasses as infrared materials began in 1950 when R. Frerichs2,3 rediscovered arsenic trisulfide glass. Good infrared transmission had been reported previously4 in 1870. W. A. Fraser and J. Jerger5 continued the development of the glass into a product at Servo Corporation in 1953. Devices were developed 5.0 Bandgap vs. molecular weight for semiconductors

4.0 ZnS

Bandgap (eV)

ZnO

3.0 SiC ZnSe CdS GaP

ZnTe

AIAs

2.0

CdSe AISb

CdTe

GaAs InP

Si

1.0 Ge

GaSb PbTe

InAs

InSb

Sn

0

0

50

100

150

200

250

300

Molecular weight

FIGURE 1.1 Bandgaps of IV, II–VI, and III–V crystalline compound semiconductors as a function of their molecular weights.

350

3

4

Chapter One using arsenic trisulfide glass lenses to sense overheated bearings on railroad cars. In further efforts, many chalcogenide glass compositions were discovered and evaluated at Servo6 Corporation. Arsenic trisulfide glass is a red glass. Other sulfur glass compositions may show visible light transmission. Most of the glasses based on selenium or containing tellurium are opaque to the visible region and show metallic luster. As stated before, glasses have energy band structure similar to that of crystalline materials employing the same elements. The chalcogenide glasses are electronic conductors with free electrons and holes as are their crystalline counterparts. However, their disordered nature leads to very low carrier mobility. Glasses based on sulfur and/or selenium are very high in resistivity, almost semi-insulators. Glasses containing tellurium have a more metallic nature and may have fairly low resistivity. For selenium glasses, except those containing sulfur, transmission begins at their absorption edge, which for the most part is 1 µm or more in wavelength. An example of the beginning of transmission for a chalcogenide glass is shown in Fig. 1.2. The glass is an arsenic selenide glass designated Amtir 4 by AMI, and the

1.0 µm 70 0.9 µm

1.25 µm

1.5 µm

1.75 µm

2.0 µm 70

0.8 µm

60

50

50

40

40

30

30

20

20

10

10 Amtir 4 absorption edge transmission (2.6 cm thickness)

0

FIGURE 1.2

0

Absorption edge for Amtir 4, an arsenic-selenium glass.

Tr a n s m i s s i o n o f L i g h t b y S o l i d s true transmission is about 65 percent at 1.5 µm, decreasing rapidly to 0 percent at about 0.84 µm. The shape of the curve changes with thickness which in this case is 2.6 cm. A thicker sample would hit zero sooner at a longer wavelength due to internal absorption. The 65 percent transmission would be essentially the same for a thinner piece since the absorption in that wavelength is very slight. The limit of 65 percent is due to Fresnel reflection loss, which is determined by the refractive index of the glass. The optical constants for the glass or any solid are discussed later.

1.3

Long-Wavelength Cutoff The long-wavelength limit for an infrared optical material is usually determined by a multiphonon lattice band, a combination band, or some vibrational absorption involving constituent atoms of the solid. A qualitative understanding of the factors involved in determining the long-wavelength cutoff for materials may be obtained by considering the expression for the frequency of a simple free diatomic vibration 1/2

fo =

1 k   2 π µ 

where fo = fundamental frequency for vibration between atoms of elements A and B k = force constant for chemical bond between atoms A and B µ = reduced mass for elements A and B, from 1 1 1 = + µ ma mb where ma and mb are the atomic masses of elements A and B When infrared energy with a wavelength corresponding to the frequency of vibration is absorbed by the molecular pair, the pair is raised to a higher vibrational energy level. Energy is increased in the solid. The absorption strength depends upon the ionic character between atoms A and B. If the atoms are the same, purely covalent, as in silicon-silicon or germanium-germanium, the absorption is weak or nonexistent. A purely covalent bond means the negative and positive centers of charge between the atoms coincide—there is no separation. Linus Pauling7 developed the concept of electronegativity values for each atom. If the atoms are different, in a Pauling electronegativity sense, there is some separation of charge between the atoms, some ionic character. Separation of charge constitutes an electric moment or dipole in the chemical bond. The dipole couples with the electric field of the infrared light, allowing energy to be transferred from the light to the molecule. For crystalline solids, the absorption may be very intense which leads to the presence of a strong infrared reflection peaks often referred to as a Reststrahlen band. Examples will be shown in later discussions for ionic solids, crystalline semiconductors.

5

Chapter One In general, one may say that good physical properties are the result of strong chemical bonds formed between atoms of low atomic mass. The combination of strong bonds (large k) and small atomic mass (small µ) leads to high vibrational frequencies that fall in the wavelength region of interest. Oxide materials are not useful in the longer infrared wavelengths for this reason. Generally speaking, it will become apparent that infrared optical materials transparent out to 14 µm do not have good physical properties. Fair predictions may be made concerning the vibrational frequencies for crystalline compounds. Figure 1.3 shows a plot of the transverse optical mode wavelengths for III–V compound semiconductors, group IV elemental solids, II–VI crystalline semiconductors, and alkali halides8 as a function of molecular weight. Figure 1.4 shows the fact that a multiphonon process, a multiple of the fundamental, transmission to 14 µm requires a solid made from heavy atoms. A good 100

KI

Lattice absorption wavelength vs. molecular weight 90

KBr

80 CdTe KCI

70 Lattice absorption (µm)

6

CdSe NaCl

60

ZnTe InSb

50

ZnSe CdS

40

ZnS

GaAs

Ge

30

ZnO

20

GaP

GaSb InAs

InP AISb

ZnO

Si Si

10 C

SiC BP

C

0

0

50

100

150

200

250

300

350

Molecular weight

FIGURE 1.3 The wavelength corresponding to the transverse optical mode frequency for group IV semiconductors, II–VI and III–V compound semiconductors as a function of their molecular weights.

Tr a n s m i s s i o n o f L i g h t b y S o l i d s

400

500

600

700

800

900

1000

1400 1300 1200 1100

PERKIN ELMER cm–4

20.9093; 57.80%T

8.9053; 74.77%T

%R

100.00

26.000

24.000

22.000

20.000

18.000

16.000

14.000

12.000

10.000

8.000

0.00

µ –1,

X: 10 scans, 2.0 cm apod none IR REFLECTION OF GLASSY QUARTZ

FIGURE 1.4

Far infrared reflection spectra of glassy quartz.

rule of thumb to follow9 is that the cutoff occurs at twice the frequency of the highest longitudinal optical mode. Predictions of lattice mode frequencies can be made to a fair degree of accuracy using a number of empirical methods. For example, the lattice structure for a crystal compound AB can be predicted from Pauling electronegativity differences for the binary AB and the principal quantum numbers of their bonding electrons. These concepts were first proposed by Mooser and Pearson.10 The concepts were enlarged by Parthe.11 A lattice mode treatment using empirical force constant tables,12 of which there are many, should lead to a fairly accurate prediction of the long-wavelength cutoff for a hypothetical solid. The spectroscopic selection rules for active vibrations in crystalline solids rely on symmetry of the crystal cell. A crystal has long-range order in the spatial arrangement of the atoms relative to one another. As a consequence, not all vibrational modes are active due to symmetry considerations. For glasses, the structure is molecular with no longrange order. There is no symmetry. All modes are active. It should be mentioned that the elemental semiconductors germanium and silicon

7

Chapter One have zero Pauling electronegativity differences, so their fundamental lattice modes are not spectroscopically active. In both materials, weak absorption by higher-order lattice vibration modes is observed. An example of far infrared Reststrahlen-type reflection bands in glasses is shown in Fig. 1.4. The infrared reflection for glassy quartz is measured using the AMI Perkin Elmer FTIR spectrophotometer. Note the very strong band at about 20 µm followed by another strong band at 9 µm, about one-half the wavelength of the other. Note the reflection peaks are 75 and 58 percent, really quite strong. Keep in mind that the degree of ionic character in the silicon-oxygen bond is considerable in comparison to those of the selenium-based covalent glasses. The second band stops the infrared transmission of glassy quartz, although it had already been stopped by the inpurity of water, which absorbs strongly at 2.9 µm. As mentioned earlier, infrared materials transmitting to 14 µm are formed from heavier elements and do not generally have good physical properties. One physical property important for producing lenses from optical materials is surface hardness. Figure 1.5 shows a 10,000 C

Surface hardness as a function of molecular weight for semiconductors

BP SiC

Knoop hardness

8

Si

1,000

GaP Ge

GaAs InP ZnS

GaSb InAs

AISb InSb

ZnSe CdS

100

CdTe

0

50

100

150

200

250

300

Molecular weight

FIGURE 1.5 Knoop hardness of crystalline semiconductors as a function of their molecular weights.

Tr a n s m i s s i o n o f L i g h t b y S o l i d s plot of Knoop surface hardness for crystalline semiconductors as a function of molecular weight. Some of these materials are useful as infrared (IR) optical materials. Note the low Knoop hardness values with increasing mass. To summarize, the transmission range of a solid is determined by the bandgap of the material on the short-wavelength side and a lattice-type absorption band involving constituent atoms on the longwavelength side. Both quantities are qualitatively predictable from the location of the elements in the periodic table, as will be discussed later. An example of Reststrahlen-like reflection bands for some chalcogenide glasses is shown in Fig. 1.6. The percent reflections for As2S3 glass, Ge2S3 glass, a Si-As-Te glass, and a Ge-P-Te glass, all measured in the far infrared using the Perkin Elmer 301 infrared spectrophotometer at TI, are shown. Note the percent reflection for these glasses is much smaller than that shown by glassy quartz. The fundamental frequencies for the As—S bond, the Ge—S bond, the Si—Te bond and the Ge—Te bond in the glasses are all near the peak of their respective reflections. Their long wavelength cutoff then is about one-half the wavelength of their peaks. Figure 1.7 depicts the transmission range of glasses based on sulfur, selenium, or tellurium. We see the sulfur-based glasses showing some visible light transmission but cutting off after 10 µm. Notice transmission rates for sulfur-based glasses are the highest because the Fresnel loss is less due to their lower refractive index. 50

Ge15P15Te70

% Reflectivity

40

Si10As10Te2O 30

As2S3 20 Ge2S3 10

0

0

10

20 30 40 Wavelength (micrometers)

50

FIGURE 1.6 Far infrared reflection spectra of some chalcogenide glasses.

60

9

10

Chapter One Oxides 100

%T or %R

S

Se Te

50

S

0

1.0

10

30 20 Wavelength (µm)

Se

40

Te

50

60

FIGURE 1.7 Pictorial representation of the transmission range for glasses based on sulfur, selenium, or tellurium.

The selenium-based glasses start transmitting at about 1 µm and start cutting off after about 12 µm. The tellurium glasses start transmitting at about 2 µm and cutting off about 20 to 30 µm. Tellurium glasses have the highest index and are the hardest to make without crystallizing. This depiction is for only one chalcogen in the composition. Mixed chalcogen glasses such as sulfur-selenium or selenium-tellurium will be somewhat different with regard to transmission, index, and tendency to crystallize.

1.4

Extrinsic Loss within the Band, Impurities, Scatter, and Quality Electronic, vibrational, or physical defects related to purity or method of preparation may affect the performance of a material within the transmission range. Thus, in a general sense, the effects are considered extrinsic, not intrinsic, to the solid. Impurity atoms in crystalline semiconductors may be electrically active in the host material, leading to charge carriers in excess of intrinsic levels. The free carriers with high mobility classically in semiconductors may absorb infrared radiation in proportion to the infrared wavelength squared.13 Inclusion of scattering terms may lead to a dependence greater than wavelength squared. Intervalence band transitions may produce absorption bands in P-type materials such as germanium and gallium arsenide. Examples of such effects are described in standard texts such as the one by Moss.14 The solution for low carrier mobility materials

Tr a n s m i s s i o n o f L i g h t b y S o l i d s such as found in chalcogenide glasses leads to an expression independent of wavelength.12 Free carrier absorption for melt-formed chalcogenide glasses used for optical applications has not been observed but has been reported15 for highly conducting chalcogenide glasses containing tellurium used in electronic devices. The presence of impurity atoms such as oxygen, water, and carbon bonded to constituent atoms leads to localized molecular absorption bands. Classic examples are the 9-µm absorption in silicon due to the Si—O bond,16,17 the 11.6-µm absorption in germanium due to the Ge—O17 bond, and a Si—C absorption for C12 in silicon at 16.5 µm.18 It is interesting to note the fundamental for pure Si—C occurs at 12.6 µm.19 Molecules such as water (H2O), hydrogen sulfide (H2S), or hydrogen selenide (H2Se) occur often in sulfur or selenium glasses. The impurity molecules couple (in a weak bond) to the positive element in the glass composition. An arsenic-selenide glass has only one absorption band due to H2Se at about 4.6 µm while an arsenic-germaniumselenium glass has two absorption bands, one for arsenic at 4.5 µm and one for germanium at 4.9 µm. A sulfur glass will have an absorption for water at 2.9 µm and one for hydrogen sulfide at 4 µm. Siliconoxygen (Si—O) absorption will occur at about 9.5 µm in glasses if present as an impurity. Hydrocarbons present during the compounding process for selenium glasses lead to the formation of H2Se due to the reaction of liquid selenium with a hydrocarbon. A laboratory method used to generate small amounts of H2Se is to melt paraffin and selenium together. Localized absorption due to low-level impurities in crystals or glasses produces narrow sharp bands useful for determining the impurity concentration. Crystal materials are often grown from a melt in near-perfect lattice form. There is little chance of bubbles or particulate inclusions. Vaporgrown polycrystalline materials may contain particulate matter from the gases or vapors used in the growth. Glasses are formed from melts as well. The melts may be in containers opened to the atmosphere or sealed in evacuated chambers. Glasses are usually mixed by some form of agitation of the melt to ensure complete reaction of the components and to form a homogeneous melt from which the solid forms. Bubbles may form during the process. Often, at the end of the compounding mixing process, agitation will be stopped and a period of time is allowed for the bubbles to rise to the surface and be eliminated. Bubbles act as hollow spheres in the glass, scattering the light. Most optical glass specifications allow bubbles with no larger than 0.002-in diameter and only a few. Inert particulate matter may also be present in the glass due to contaminate in the reactants. Such particles are small and absorb light. Some glass compositions produce crystallites during processing. Crystallites may be distinguished from particles on examination because they generally transmit light and crystalline facets. Crystallites, as bubbles, cause transmission loss.

11

12

Chapter One There is usually a slight difference in the refractive index of the crystallite from the glass from which it formed. Because of this difference, light is reflected (scattered) at each surface interface and is a transmission loss. The scattering particles may range from the microscopic to the macroscopic. The intensity of light scattered at right angles to the incident light depends upon the particle size relative to the wavelength of light and upon the difference between the particle and the surrounding medium.15 Such would be the case for large-grain polycrystalline materials. As particles become very small relative to the wavelength, the intensity drops off dramatically, as the inverse of the wavelength to the fourth power. Another source of loss of transmitted light and optical distortion is striae in glass. During the glass process, local variations in composition or density produce regions where the refractive index is different from that of the whole. The beam can be diverted in direction in these local regions, harming the integrity of the transmitted image or reducing the intensity of light reaching the detector plane. The supplier must develop a reliable process to supply high-purity, homogeneous glass, free of bubbles, particles, striae, and crystallites.

1.5

Optical Constants and Dispersion due to Strong Absorption If a beam of light in air incident on a flat surface at an angle of O1 from the normal and the refracted beam is O2 from the normal, the refractive index may be calculated20 from N1 sin O1 = N2 sin O2. Since N1 for air is ~1.000, N2 =

sin O1 sin O2

The refractive index of an optical material is not a constant, and how it varies with wavelength is perhaps the most important parameter for its use by an optical designer. Already we have seen that Fresnel reflection losses decrease transmission for a material. The Fresnel reflection coefficient R can be calculated20 from the expression R=

(N − 1)2 (N + 1)2

Again, the value of R is not a constant since N changes with wavelength. The greater the value of N, the higher the value of R. Thus far, we have accounted for the Fresnel reflection losses only from transmission. Losses due to absorption must be measured and calculated from the expression T=

(1 − R)2 e −αx 1 − R 2 e −2αx

Tr a n s m i s s i o n o f L i g h t b y S o l i d s where T = transmission I/I0 R = reflectivity α = bulk absorption coefficient, cm–1 X = sample thickness, cm Optical designers desire index values to five numbers for imaging systems. How these values are obtained will be discussed in a later section. Absorption values may be calculated from measured transmission by using the sample thickness and precise index values. The full transmission expression may be programmed at wavelength points with thickness and transmission as variables. Another method often used incorporates two samples of different thickness with the change in transmission used in the solution for the absorption value. All discussions thus far pertain to the transparent region where absorption is low. In this region the index is taken as a simple number. However, the index and the absorption coefficient are interdependent. That is, the index is really a complex number and should be written20 as

N = n − ik where n = real part of index k = imaginary part, the absorption coefficient α = 4πk/λ α = bulk absorption coefficient, cm–1 λ = wavelength, cm In the transparent region, the value of k is so small it can be ignored. However, in strong absorption wavelength (big k) regions such as at the electronic absorption edge or where lattice-type absorption between constituent atoms occurs, the real part of the index changes dramatically as k increases. The optical constants are interdependent. The effect of these two regions, one on each end of the transmission region, carries over into the transparent region as a major factor in the dispersion or change in index with wavelength. The other major factor is change in temperature. As a solid expands or contracts, the number of atoms per cubic centimeters changes. The density changes. The index reflects the mass of the atoms in the solid and the number of atoms per cubic centimeter. The variation of the refractive index with wavelength in the transparent range may be depicted with the use of two dispersion curves, one at each end, shown in Fig. 1.8. The first depicts the change in reflectivity that occurs at the electronic absorption edge for a solid. At the short-wavelength side the reflectivity first falls as the absorption k increases. Then reflectivity increases as k rises to a maximum. On the long-wavelength side of the peak, k falls to a negligible value, and the reflectivity falls and levels out at a value slightly greater than before. Thus, the refractive index has increased. The real part of the index n first falls as k increases and then as k declines returns to a value greater

13

14

Chapter One Infrared transparency

Wavelength, µm

Electronic absorption edge

Vibrational absorption cutoff

FIGURE 1.8 Two dispersion curves separated in wavelength depicting the change in refractive index due to the strong absorption at the electronic edge and near the lattice-type absorption. Their interactions affect the refractive index in the transparent region.

than before the influence of strong k. On the long-wavelength lowenergy end, we have a dispersion curve for the lattice-type absorption between constituent atoms. As before, in the short-wavelength side of the strong absorption, the reflectivity and index fall below level, rebound to a peak close to the maximum absorption (k), and finally declines to a level above the previous level as k becomes negligible. The index increases on the long-wavelength side of the electronic edge absorption and decreases in the short-wavelength side of the cutoff absorption due to constituent atoms. The overall effect in the transparent region depends upon how close in wavelength the two effects are to each other. When the solid is heated, both absorptions broaden and shift in wavelength, contributing to a thermal change in index. The other factor is volume expansion. For materials like the alkali halides, the absorption edge and lattice cutoff are widely separated in wavelength. Hence, the volume expansion prevails, and there are negative changes in index with temperature as the number of atoms per cubic centimeter declines.

References 1. 2. 3. 4. 5. 6.

G. K. Teal, M. Sparks, and E. Buehler, Phys. Rev. 81, 637 (1951). R. Frerichs, Phys. Rev. 78, 643 (1950). Rudolph Frerichs, J. Opt. Soc. Am. 43, 1153 (1953). C. Schultz-Sellack, Ann. Physik 139, 162 (1870). W. A. Fraser and J. Jerger, J. Opt. Soc. Am. 43, 332 (1953). J. Jerger, Jr., and R. Sherwood, “Investigate the Properties of Glasses Transmitting in the 3 to 5 and 8 to 14 Micron Windows.” Servo Corp., Hicksville. L.I.N.Y. Final Tech. Report, Contract No. Nonr 4212(00), August 1964. 7. Linus Pauling, The Nature of the Chemical Bond, Cornell University Press, Ithica, N.Y., 1948.

Tr a n s m i s s i o n o f L i g h t b y S o l i d s 8. E. Burstein, “The Intrinsic Infrared and Lattice Vibrational Spectra of Cubic Diatomic Crystal,” Lattice Dynamics, Proceeding of the International Conference, Copenhagen, 1963. 9. William B. White, “Infrared Transmitting Materials,” Report No.1, Contract No. 14-67-0385-005, Office of Naval Research, December 1968. 10. E. Mooser and W. B. Pearson, Acta Crystallogr. 12, 1015 (1959). 11. E. Parthe, Chemical Structure of Tetrahedral Structures, Gordon and Breach Science Publishers, New York, 1964. 12. G. R. Somajula, J. Chem. Phys. 28, 814 (1958). 13. See standard SC texts such as Semiconductors by R. A. Smith, Cambridge, MA, 1959. 14. T. S. Moss, Optical Properties of Semiconductors, Academic Press, New York, 1959. 15. D. L. Mitchell, S. G. Bishop, and P. C. Taylor, J. Non. Cryst. Sol. 8−10, 231 (1972). 16. W. Kaiser and P. H. Keck, J. Appl. Phys. 28, 882 (1957). 17. W. Kaiser, P. H. Keck, and C. F. Lang, Phys. Rev. 101, 1264 (1956). 18. R. C. Newman and J. B. Willis, J. Phys. Chem. Solids 26, 373 (1965). 19. W. G. Spitzer, D. Kleinman, and D. Walch, Phys. Rev. 113, 127 (1959). 20. R. W. Ditchburn, Light, Dover Publications, Mineola, N.Y., 1991.

15

This page intentionally left blank

CHAPTER

2

Chalcogenide Glasses 2.1

Historical Development The investigation of chalcogenide glasses as optical materials in infrared systems began with the rediscovery of arsenic trisulfide glass1,2 by R. Frerichs in 1950. Good transmission for arsenic trisulfide had been reported in 1870.3 Development of the glass as a practical optical material was continued by W. A. Fraser and J. Jerger4 in 1953 at Servo Corporation. During the 1950–1970 period, the glass was made in ton quantities by American Optical and Servo in the United States and by Barr and Stroud in the United Kingdom along with several others in Europe. The glass was used for commercial devices. As an example, devices that detected overheated bearings on railroad cars were made and marketed by Servo Corporation. Hot objects could be detected at this time by radiation transmitted through the 3- to 5-µm atmospheric window where arsenic trisulfide glass was transparent. However, the need for other chalcogenide glass compositions capable of transmitting longer wavelengths arose with the concept of passive thermal optical systems. Jerger, Billian, and Sherwood5–7 extended their investigation of arsenic glasses containing selenium and tellurium, and later adding germanium as a third constituent. The goal was to use chalcogen elements heavier than sulfur to extend long-wavelength transmission to cover the 8- to 12-µm window and at the same time improve physical properties. In parallel, Russian work at the Ioffee Institute in Leningrad under the direction of Boris Kolomiets was reported in 1959.8 Work along the same line was begun in the United Kingdom by Nielsen and Savage9–11 as well. The Royal Radar work led to limited production of chalcogenide glass at the British Drug House Laboratories. The U.K. results are summarized in a recent book by Savage.12 Work at Texas Instruments (TI) began as an outgrowth of the thermoelectric materials program. The glass forming region for the

17

18

Chapter Two silicon-arsenic-tellurium system was mapped out by Hilton and Brau.13 This development led to an exploratory DARPA- ONR program at TI, funded from 1962 to 1965.14 The ultimate goal of the program was to find infrared transmitting chalcogenide glasses with physical properties comparable to those of oxide optical glasses and a softening point of 500°C. An attempt was made to achieve this goal by incorporating transition element titanium in the composition.15 Further work16 was funded on sulfur-based glasses in 1973 to 1974. The exploratory programs resulted in eight chalcogenide glass U.S. patents. Three papers were published in an international journal detailing the results.17 As a result of publishing the three papers, the author was invited to present a paper at the Fourth All-Union Symposium on the Vitreous Chalcogenide Semiconductors held in May 1967 in Leningrad (now called St. Petersburg). While at the meeting, the author met Valentina Kokorina, head of the Russian chalcogenide glass production facility. Valentina Kokorina, now retired, recently published a book detailing the Russian effort.18 Representing the West also was Prof. Douglas McKenzie of the University of California, Los Angeles, a well-known glass scientist. From the University of Edinburgh in Scotland was Prof. Alan Owen, head of the Electrical Engineering Department. Another from the West at the meeting was Stanley Ovshinsky, founder of Electron Energy Conversion Devices in Troy, Michigan, who presented his first paper advocating switching devices based on the electronic properties of chalcogenide glasses. Similar work in the United States was reported earlier by A. David Pearson19 of Bell Telephone Laboratories. Thus started a great worldwide effort to investigate chalcogenide glasses and their electronic properties. The purpose was to pursue a new family of inexpensive electronic devices based on amorphous semiconductors. The effort in this field far exceeded the effort directed toward optical applications. Some of the results of the efforts in the United States were reported in a symposium in 196920 and in another symposium in 1971.21 Generally, the glasses used could be made conducting with applied voltage resulting in the formation of a crystalline filament path. Such glasses were not suitable for optical use and are not discussed in this book. Our discussion concentrates on efforts in the United States to develop infrared optical materials, specifically, chalcogenide glasses from groups IVA, VA, and VIA from the periodic table. In 1966, the Air Force decided to fund a Research Program on Infrared Optical Materials at Central Research Laboratories at TI. There was a six-month delay in funding. During this time, Robert Patterson mapped out the glass forming region for the germaniumantimony-selenium system. A U.S. patent22 was granted covering the best composition selected, TI 1173. When the author returned to the United States in 1967 and reported the existence of a chalcogenide glass production facility in Russia the Air Force decided to fund a Development Program at TI with a goal of

Chalcogenide Glasses establishing a similar glass production facility. Funding for this purpose by the Air Force covered the years 1967 through 1974. Also in 1967, a Materials Advisory Panel23 was formed headed by Norbert Kreidl, a noted glass scientist and former director of research at Bausch and Lomb. The author was a member of the panel. One of the recommendations of the panel was that a program be funded to develop zinc selenide as an infrared optical material. The Air Force decided to fund a Raytheon program headed by Jim Pappis.24 The development at Raytheon of the chemical vapor deposition method to produce plates of small-grain zinc selenide and zinc sulfide has been a very important advancement in the production of infrared optical elements. In 1967, the Air Force Production Development Program at TI was transferred to the Semiconductor Production Division under the direction of Charlie Jones, a colleague of the author from the Central Research Laboratory. Joining the effort was Harold Hafner who had just joined TI. His background was in glass science as he had served as deputy research director at Bausch and Lomb under Norbert Kreidl. Hafner made many important contributions including a glass casting process and a glass tempering process. The program concentrated the efforts on a glass from the germanium-arsenic-selenium system. TI results25 agreed with the conclusions of the Russian, U.K., and Servo efforts that the germanium-arsenic-selenium system produced the best glasses for infrared system applications. Don Weirauch at TI conducted a crystallization study on the germanium-arsenicselenium family of glasses and identified a composition in which crystallites would not form. The composition was fully characterized and produced at Texas Instruments as TI 20 glass. No patent could be granted for the glass since the glass system was reported in several places in the literature. One of the accomplishments of the program was to increase the rupture modulus of TI 20 from 3000 to 6000 psi by tempering. In 1972, a window of TI 20 glass was cast 12 in × 24 in × 0.5 in, polished flat and parallel and antireflection-coated.26 The window was installed in a U.S. Navy F4 in front of its FLIR system. The plane on returning to Florida flew into a hailstorm, which shattered the window and damaged the FLIR. Thus started the rain erosion testing of infrared optical materials at the facility at Wright-Patterson Air Force Base. Attempts were made at TI to develop a business selling infrared glass outside the company. Brochures and advertising were employed. Little in sales resulted. The program had reached a production stage and was moved to the Electro-Optics Division, the user division. Production of TI 20 was stopped as well as sales of chalcogenide glasses outside the company. In 1972–1973, TI had to produce the glass in quantity and quality for the Navy P3 system. Their yields were so low that glass blanks began to cost more than the system. In 1974, the author left TI Central

19

20

Chapter Two Research, moved to the TI EO Division, and took over the glass production program. His efforts succeeded and yields improved, leading to decreased cost. Standard production became 7-kg plates 12 in × 12 in of TI 1173. In the late 1960s and early 1970s, passive 8- to 12-µm systems began to be produced in small numbers, mostly for the Air Force or Navy. The numbers were in the hundreds, corresponding to the number of airplanes. Notably was the system for the B52 made by Hughes Aircraft. The potential numbers reached thousands when the customer became the Army. The Army embraced a common module approach whereby different companies could all build from the same design. There would be three programs: the ANTAS for the Infantry, the Tank Thermal Sight, and TADS PNVS for the helicopter. All companies could compete, and the winner’s design would be adopted as the common module. Since the wavelength range was wide, color correction would be necessary which meant that a second optical material would be needed to go along with germanium, by then the industry standard. The TI design used TI 1173 with germanium. TI won the first two programs. The Army became aware of the fact that TI was the only source of the glass used in their common modules. The third program, TADS PNVS, had not been decided. It became obvious to the author that a second source of glass would be needed. Early in 1977, the author gave notice to TI that he planned to leave the company. He was called in and told by TI that he would be allowed to produce the glass. The Army was told that there would soon be a second source. However, the Army awarded the TADS PNVS contract to Martin Marietta in 1977. Thus, for two of the programs the Army was committed to a design that used a patented glass as the second material, not available to competitors. The alternate glass, TI 20, was no longer in production at TI. Clearly a second source of glass was needed to ensure the success of the Army common module approach. The author left TI in 1977 and in May founded Amorphous Materials (AMI). Very soon he found TI had changed its mind and would not license Amorphous Materials to produce TI 1173 glass. The decision was made to produce the TI 20 germanium-arsenic-selenium glass at AMI because its physical and optical properties had been fully studied and published in a government report.25 Besides, TI 20 was a better glass than TI 1173. The glass was not and could not be patented. Next, AMI had to convince the Army that producing this glass would save the concept of the common module approach. It took over a year to persuade the Army to help AMI. The effort was supported through a three-year Manufacturing Methods and Technology Program funded by the Army through the Night Vision Laboratory at Ft. Belvoir. Amorphous Materials renamed the glass composition Amtir 1 and went on to supply Magnavox, Kollsman Instruments,

Chalcogenide Glasses Hughes, Martin Marietta, and Westinghouse in several programs. Amtir 1 is still the major FLIR glass produced by AMI. Standard production is 9-kg plates 8-in diameter. AMI has produced 35 tons of Amtir 1 glass from 1978 to 2007. Later, in 1991 after the TI 1173 patent expired, the Night Vision Laboratory provided a letter contract to qualify AMI as a second source of the glass which AMI renamed Amtir 3. It is interesting to note that in the United States during the period from 1950 to the present, only three glass compositions have been produced in ton quantities: arsenic trisulfide, TI 1173 (Amtir 3), and TI 20 (Amtir 1). No other widely used new compositions have emerged. The reason in part is due to the considerable effort required to identify, produce, and characterize a new glass composition to the state that optical designers, system designers, and corporate management are willing to use it in a new system. Even if a new, better glass emerged, there would be great reluctance to redesign a system once it is in production.

2.2 The Periodic Table and Glass Formation Previously, it was pointed out that efforts to find and develop chalcogenide glasses for infrared systems were most successful using elements from the IVA, VA, and VIA groups of the periodic table. This statement is to point out that the periodic table is not an inexhaustible supply of elemental combinations that should be investigated. The three groups named have fueled investigations of many systems: binary, ternary, or those containing even more elements. A review of other materials transparent in the infrared but from different elemental families may help to explain why some elements are favored more than others. Figure 2.1 presents a shortened version of the periodic table of the elements. Outlined are the families of the elements from which infrared optical materials are formed. As indicated in the chart, the alkali halides form from the IA alkali metal elements Li, Na, K, Rb, and Cs in combination with the group VIIA halogens F, Cl, Br, and I. The alkaline earth halides form from the IIA alkaline earth metal elements Be, Mg, Ca, Sr, and Ba in combination with the VIIA halogen elements F, Cl, Br, and I. Notice also in Fig. 2.1 that a change in Pauling electronegativity27 is indicated as one moves up or down in the chart or from left to right. On the left, the value decreases going from lighter alkali and alkaline earth elements to heavier. Thus, Cs and Ba have the lowest values for the two families. Conversely, Pauling electronegativity is indicated to be increasing with atomic number going across the chart from IA elements to VIIA elements. At the same time on the right of the chart, Pauling electronegativity increases going up the chart from the heavier halogens to the lighter elements. Fluorine in the top right corner has the highest value, 4.0, one unit higher than its next row element Cl.

21

22 +1 –1

0 2

2-1

2-2

Pauling electronegativity

2-8-1

2-3 +2

+1

2-8-3

2-8-2 +1

-8-8-1

+2

-8-8-2 +1

2-4 +3

+2

+3

+2 +3 +4

+2 +3 +4 +5

+2 +3 +6

+2 +3 +4 +7

+2 +3

+2 +3

+2 +3

+1 +2

+2

+3

+1 +2 +3 +4

+2 +4 –4

+3

+2

+5 –1 –2 –3

2-5 +2 +4 –4

–2 2-6

+3 +5 –3

–1 2-7

+4 +6 –2

0 2-8

+1 +3 +7 –1

0

2-8-4 2-8-5 2-8-6 2-8-7 2-8-8 +1 +4 +2 0 +3 +5 +6 +4 +5 –1 –2 –3

-8-9-2 -8-10-2 -8-11-2 -8-13-1 -8-13-2 -8-14-2 -8-15-2 -8-16-2 -8-18-1 -8-18-2 -8-18-3 -8-18-4 -8-18-5 -8-18-6 -8-18-7 -8-18-8 +1 +3 +4 +3 +3 +2 +4 +3 +4 +3 0 +3 +2 +1 +2 +6 +5 +5 +6 +5 +4 +6 +7 +4 –1 –3 –2 +7

-18-8-1 -18-8-2 -18-9-2 -18-10-2 -18-12-1 -18-13-1 -18-13-2 -18-15-1 -8-16-1 -18-18-0 -18-18-1 -18-18-2 -18-18-3 -18-18-4 -18-18-5 -18-18-6 -18-18-7 -18-18-8 +4 +3 +2 +1 0 +1 +3 +5 +1 +2 +3 +3 +2 +2 +1 +6 +4 +6 +4 +4 +3 +5 +3 +4 +4 +4 +2 +7 -18-8-1 -18-8-2 -18-9-2 -32-10-2 -32-11-2 -32-12-2 -32-13-2 -32-14-2 -32-15-2 -32-17-1 -32-18-1 -32-18-2 -32-18-3 -32-18-4 -32-18-5 -32-18-6 -32-18-7 -32-18-8 +2 +3 +1 +4 223.0197 -18-8-1 -18-8-2

Db

-18-9-2

Sg

263.112 262.114 266.1219 -32-10-2 -32-11-2 -32-12-2 -32-13-2 -32-14-2 -32-15-2 -32-16-2

Pauling electronegativity Alkali halides, IA elements Li, Na, K, Rb, Cs with VIIA elements F, Cl, Br, I Alkaline earth halides, IIA elements Be, Mg, Ca, Sr, Ba with VIIA elements F, Cl, Br, I II–VI crystalline compounds, IIB elements Zn and Cd with VIA elements S, Se, Te Elemental crystalline semiconductors, IVA Si, Ge, Sn Compound crystalline semiconductors, IIIA elements Ga, and In, with VA elements P, As, Sb Chalcogenide glasses, IVA elements Si, Ge, Sn along with VA elements P, As, Sb combined with VIA elements S, Se, Te

FIGURE 2.1

Designation of the elements from which infrared optical materials are formed.

Pauling Electronegativity

+1

Chalcogenide Glasses A purely covalent bond, such as exists in amorphous selenium or crystalline silicon, has an even distribution of the bonding electrons between the two atoms, zero percent ionic character. The positive and negative centers for the atom pair coincide midway between. A large value of electronegativity indicates a negative element which tends to attract and hold the bonding electrons closer and away from the positive element. A low electronegativity indicates a positive element which tends to furnish the bonding electrons to the other atom. The positive and negative centers for the atom pair do not coincide. The bond has ionic character. Pauling electronegativity27 values for the important elemental families already mentioned are listed below: Pauling Electronegativity Elemental Values IA

IIA

IVA

VA

VIA

VIIA

Li 1.0

Be 1.5

C 2.5

N 3.0

O 3.5

F 4.0

Na 0.9

Mg 1.2

Si 1.8

P 2.1

S 2.5

Cl 3.0

K 0.8

Ca 1.0

Ge 1.8

As 2.0

Se 2.4

Br 2.8

Rb 0.8

Sr 1.0

Sn 1.8

Sb 1.9

Te 2.1

I 2.5

Cs 0.7

Ba 0.9

Pb 1.8

Bi 1.9

Po 2.0

At 2.2

One should notice the values for oxygen and sulfur are a full unit different which is significant in the fact that oxides and other chalcogenides are very different from one another. Oxygen is a gas at room temperature while sulfur, selenium, and tellurium are solids and in amorphous forms made up of chains and rings in a polymerlike structure. Nitrogen and fluorine are also gases. First-row elements are not important to our chalcogenide glass formation discussion. First, we will look at the percent ionic character in the chemical bonds formed between the elements of the alkali halides and the alkaline earth halides. Using XA and XB as the electronegativity values for elements A and B, in the following table percent ionic character for the A-B bond is found from XA − XB = ∆. ∆ 0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1

2

4

6

9

12

15

19

22

26

30

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

Percent Ionic 34

39

43

47

51

55

59

63

67

70

74

76

∆ 2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

Percent Ionic 79

82

84

86

88

89

91

92

Percent Ionic 0.5 ∆ .13

23

24

Chapter Two Applying these numbers to the alkali halides, we find their bonds average more than 50 percent ionic character. For the often used alkali halide NaCl, ∆ is 2.1 which corresponds to 67 percent ionic character. The same procedure applied to alkaline earth halides averages to about 50 percent. For the often used alkaline earth halide CaF2,, ∆ is 3.0 which corresponds to 89 percent ionic character. Both families are broadband in transmission from the ultraviolet and some into the far infrared. Their refractive indexes are relatively low while their expansion coefficients are large, leading to negative changes in index with temperature. Some can be grown in large single-crystal form but are soft and weak and may cleave. Their melts are not viscous. Most are readily attacked by water. Alkali halides are used mostly in the laboratory. A major exception among the alkaline earth halides for system use is fine-grain polycrystalline magnesium fluoride. The point is that these materials are ionic crystalline solids and as such are not useful in night vision systems used in the field. The same treatment applied to the combinations in the IVA, VA, and VIA elements illustrates the covalent nature of the chalcogenide infrared glasses.

IVA Atom Pairs



Percent Ionic VA Atom Pairs



Percent Ionic

Si 1.8–O 3.5

1.7

51

P 2.1–O 3.5

1.4

39

Si 1.8–S 2.5

0.7

12

P 2.1–S 2.5

0.4

4

Si 1.8–Se 2.4

0.6

9

P 2.1–Se 2.4

0.3

2

Si 1.8–Te 2.1

0.3

2

P 2.1–Te 2.1

0

0

55

As 2.0–O 3.5

1.5

43

Ge 1.7–O 3.5

18

Ge 1.7–S 2.5

0.8

15

As 2.0–S 2.5

0.5

6

Ge 1.7–Se 2.4

0.7

12

As 2.0–Se 2.4

0.4

4

Ge 1.7–Te 2.1

0.4

4

As 2.0–Te 2.1

0.1

Sn 1.7–O 3.5

1.8

55

Sb 1.9–O 3.5

1.6

47

0.5

Sn 1.7–S 2.5

0.8

15

Sb 1.9–S 2.5

0.6

9

Sn 1.7–Se 2.4

0.7

12

Sb 1.9–Se 2.4

0.5

6

Sn 1.7–Te 2.1

0.4

4

Sb 1.9–Te 2.1

0.2

1

Pb 1.9–O 3.5

1.6

47

Bi 1.9–O 3.5

1.6

47

Pb 1.9–S 2.5

0.6

9

Bi 1.9–S 2.5

0.6

9

Pb 1.9–Se 2.4

0.5

6

Bi 1.9–Se 2.4

0.5

6

Pb 1.9–Te 2.1

0.2

1

Bi 1.9–Te 2.1

0.2

1

Excluding oxygen bonds, the IVA elements bonded with VIA elements average 8 percent ionic character, and the VA bonds with VIA elements average only 4 percent. One may ask why ionic character is important in infrared chalcogenide glasses. Covalent bonding has

Chalcogenide Glasses very specific bonding angle requirements to nearest neighbors which resist being changed by force. Myuller28 points out that the deformation of covalently bonded substances in the liquid state during viscous flow requires much more energy than the deformation of materials bonded ionically. Thus, covalent melts are viscous. The bonding requirements for ionic and metallic substances are not rigid with respect to bonding angles. Thus, metallic and ionic melts are not viscous and freeze into a solid when cooled to their melting points. Glass melts are different. Figure 2.2 shows a thermal expansion analyzer29 (TEA) curve for AMI C1 glass measured using a dilatometer. A sample about 2 in long is heated at a controlled rate, and the change in length is measured and plotted as a function of temperature. Note the slope is typical of the expansion of a solid. As the temperature increases, the slope at some point begins to gradually change, taking on a steeper slope more typical of a liquid. The intersection of the two slope lines is called the glass transition temperature Tg for the glass. For this instrument, Tg is also defined in terms of viscosity, Tg ~ 1013 poise. Had this been a crystalline material, the expansion curve would have ended abruptly at the melting point of the solid as it turned into a nonviscous liquid. As the measurement of the glass continues, a point is reached where, under the conditions of the instrument, expansion stops and the sample begins to contract. This point is called the dilatometric softening point Td of the glass. For the conditions of Amtir C1 thermal expansion (annealed, rise 0.5°C/min) 300 2004.06.09 (56.50 mm) Annealed

Td ~ 154°C

250

Expansion (µm)

α(25–75) = 2.27 × 10–5/°C 200 α(25–100) = 2.31 × 10–5/°C

Tg ~ 133°C

150 α(25–125) = 2.43 × 10–5/°C 100

50

0 0

20

40

60 80 100 Temperature (°C)

120

140

FIGURE 2.2 Measurement of thermal expansion and glass transition temperature for AMI C1 glass.

160

25

Chapter Two this instrument, Td is also defined in viscosity terms as 109.5 poise. If the glass temperature curve is approached from the other direction, i.e., cooling from above the softening point toward room temperature, the shape will be slightly different depending upon the rate of cooling (quench). As the glass is cooled into the Tg range, the slope then decreases and begins to level out to a value typical of a solid. Different rates of cooling produce a family of curves slightly separated from one another. The slight differences are reflected in the density and thus the resultant refractive index. For this reason, the thermal history of a glass is important. To stabilize the refractive index from batch to batch, the quenching process and the annealing procedure must be established and consistently followed when the glass is produced. Nucleation and growth of small crystallites in a glass melt do occur depending upon composition and temperature. The process requires movement of atoms to come together to form molecules of exact composition ratios. Such processes are much more difficult in viscous melts and occur slowly if at all. As the temperature increases, the viscosity decreases, making the crystallization process possible. Thus, the crystallization process is time- and temperature-dependent. Figure 2.3 is a differential thermal analysis (DTA) plot29 for AMI C1 glass that shows difference in temperature for a fine powder glass sample referenced against a fine powder of standard aluminum oxide powder when the samples are heated at a controlled rate. Two regions are designated. The first is at a temperature right above the Tg that dips below the reference line, an endothermic process. This change is

Amtir C1 DTA 0.20 2004.06.11 with Rickett 6th order background correction

0.15 Differential temp (°C)

26

194°C Peak exotherm (Crystallization) 172°C Endotherm

0.10 154°C Tg 0.05 0.00 –0.05 –0.10 0

FIGURE 2.3

50

100 150 Temperature (°C)

200

Differential thermal analysis (DTA) plot for AMI C1 glass.

250

Chalcogenide Glasses attributed to nucleation of very small crystallites. The second region, well above the reference line, indicates rapid growth of the crystallites, an exothermic process. After the peak is past, the curve begins to fall, indicating the crystallites are now dissolving in the surrounding low-viscosity glass. AMI C1 is an arsenic-selenium-tellurium glass which has a tendency to crystallize. Figure 2.4 shows microscope photographs of crystals forming on the surface of C1 glass after heating for an extended period. Figure 2.4a shows nucleation at 215°C for 8 h. Figure 2.4b shows much larger crystals grown at 238°C for 15 h. When producing the glass, one must quench (rapidly cool) the glass in a timely manner beginning at a temperature above the crystallization range down to a temperature below the nucleation range. These factors must be taken

(a)

(b)

FIGURE 2.4 Crystallite formation in heated AMI C1 glass. (a) C1 glass heated 8 h @ 215°C; (b) C1 glass heated 15 h @ 238°C.

27

28

Chapter Two into account when casting, molding, slumping, extruding, or drawing a glass into fiber. The rules of Zachariasen30 first pointed out that to form a glass it was important to select substances with a low coordination number (4 or less) for both the cation and the anion. Coordination number is not the only factor. There must be rigid directional requirements for the chemical bonding which is found in covalent solids such as chalcogenide glasses. Position in the periodic table for element A and element B will determine the coordination number for their binary compound AB. According to Mooser and Pearson,31 the average principal quantum number Nx of a crystalline binary AB compound is a measure of the metallic character of the bonds present. The difference in Pauling electronegativity ∆ is a measure of the ionic character of the bonds. A plot of these two factors by Mooser and Pearson31 showed that compounds of the same crystalline structures fell in the same general area of the diagram (Fig. 2.5). In fact, similar crystal structures with the same coordination number (3, 4, 5, 6, or 8) fall in rather specific areas of the plot. We have already dealt with the electronegativity differences for bonds. The principal quantum number of the valence electrons corresponds to the row of the periodic table on which the element is located. The same treatment may be applied to chalcogenide glasses. However, most compositions will not be binary, only two elements. Most will contain three or more elements. So the average principal quantum numbers and average electronegativity numbers must be calculated based on composition percentages for each element. Consider a ternary system with a composition represented by Ax + By + Cz. You calculate an average Nx by multiplying the Nx of each element by its composition fraction and adding for a total. The same procedure is followed for the electronegativity differences. The point for each composition could then be plotted as shown in Fig. 2.5. Multicomponent glasses based on silicon, sulfur, selenium, and tellurium were treated in this manner.32 Note all the chalcogenide glasses lie in the coordination number 4 area. The silicate glasses start in the 4 region but fall in the coordination number 6 region as more metal oxides are added. Note that pure SiO2 glass has a network structure that is open. Pure silica when heated is slightly permeable to helium and to a lesser extent hydrogen. The glass optical properties are altered by adding metal oxides to the composition which fill in the voids in the network structure. The heavy metal oxides are from higher row numbers of the periodic table. Bonding to silicon which already has a coordination number of 4 leads to areas of coordination number 6. Silicate glasses containing metal oxides are not permeable to helium or hydrogen. For chalcogenide glasses formed from a melt, coordination number and bond type as determined by chemical composition are the two most important factors in glass formation.

Chalcogenide Glasses

6 CN = 6 CN = 8 5 (Te)

4 (Se) Pb

2.3

Bi

3

Sr Zn Ca Cd

K

Ba CN = 4

2

SiO2

Mg Li

Na

CN = 3

1

0

FIGURE 2.5

Silicate glasses Sulfide glasses Selenide glasses Telluride glasses

7

N

Average principal quantum number for valence shell of constituent elements

8

0

1

2 ∆X Average Pauling electronegativity difference for constituent elements

3

Coordination numbers for different types of glasses.

Evaluating Possible Glass Forming Systems The discussion to follow describes the methods used and the results of the first exploratory program carried out at Texas Instruments (TI) over the period from 1962 to 1967. After the first program was finished, what was learned led to other programs which are described later. At this point, only one system had just been investigated,13 the Si-As-Te glass forming system. Development of methods and selection of systems to be investigated were just starting. In selecting elements A and B to use in a potential glass forming system, the first question to ask is, do they form a chemical bond with each other? The answer may be found in the library by using a binary compound book such as the one by Hansen.33 If a ternary three-element system is considered, the diagrams for compounds AB, AC, and BC should be found. The diagrams have temperature on both sides as the y axis while the x axis is composition going from

29

30

Chapter Two 100 percent A on the left to 100 percent B on the right. Percentages may be either weight percent or atomic percent with the latter preferred. The results presented represent equilibrium results, i.e., the reactants at a specific concentration held at a specific temperature for periods of time reaching days or even weeks. The purpose is to identify the crystalline compounds formed under the conditions of the experiment. If there is no AB compound formed, the diagram may be essentially two lines from the melting point of A to the melting point of B describing solid solutions of A and B. An example is the diagram for Ge-Si.33 A diagram might show different solid compounds in equilibrium with a liquid phase. Above all the areas outlined will be a line representing a temperature above which A and B mixtures are liquids. The liquidus curve for an AB mixture identifies a melt temperature at each indicated composition point. The same description fits the AC and the BC diagrams. If a compound is found, a straight line will be drawn down from the temperature point to the composition point. Later, we will see that the size of the glass forming area in a diagram is affected by the number of compounds that may form from the specific combination of elements. From the diagrams one may find the temperature required to produce a homogeneous melt to test the ability of the composition to form a single-phase glass when quenched. After all these years, most of the IVA-VA-VIA elements have been extensively investigated in various combinations. The investigator may wish to find a unique combination of elements with a chalcogen or even more than one chalcogen. There may be a desire to revisit previous investigations of a particular combination of elements. This discussion is only meant to serve as a guide for the start of the investigation. Obviously, the first step is to go to the literature to find any previous work that may be pertinent. The qualitative investigation of a glass forming combination of elements requires making many 25- to 50-g small samples. Quartz vials are usually used because of their purity and high-temperature softening points. High-purity reactants are used and weighed accurately with an analytical balance. The tube is evacuated to remove the atmosphere and sealed with a hydrogen-oxygen torch. Samples are then placed in some type of a rocking furnace in a hood and heated to a temperature about the same as the boiling point of the most volatile constituent element. The rocking action is begun to start the reaction of the elements. After some time, the furnace is raised in temperature to produce a homogeneous melt of the reactants. The estimated temperature is based on the binary compound diagrams. Mixing continues for some time (hours) above the melt temperature. Rocking is stopped with the vial in a vertical position. The melt is allowed to cool at the melt temperature. The vial is removed from the furnace, held in a vertical position,

Chalcogenide Glasses and quenched in air. Caution must be exercised. The vial is held by metal tongs. A face mask and protective gloves are worn. The danger of an explosion for some combinations should not be ignored. As mentioned above, the rate of cooling affects the extent of the composition range which is judged to be glass forming. After cooling, the vial is opened and the sample is removed for examination. Usually, a sample can be identified as glass or crystalline by visual examination. Sometimes use of a microscope sensitive to some degree in the near infrared is useful. A glass sample can have two phases, glass and crystal or even two immiscible glasses. If x-ray diffraction is used, a completely blank film demonstrates a singlephase amorphous glass. The glass samples are cylinders with round bottoms. Slices are carefully sawed out, some with different thickness, 2 to 5 mm. The disks are polished on both sides using an optical abrasive such as aluminum oxide. The last sample with the round bottom is saved for reflection measurements. The one flat side is polished in the same manner as the disks. The infrared transmission T is measured using a standard spectrophotometer covering the wavelength range of interest, generally 1 to 20 µm. A reflection attachment, if available, is used to measure the infrared reflectivity R from the flat side of the bottom sample. A qualitative measure of the refractive index n and the bulk absorption coefficient α can be obtained from solving the simple equation

T = (1 – R)2e–αx where x is thickness in centimeters and R ~ (n − 1)2 / (n + 1)2. In the absence of a direct measurement of R, n and α can be calculated from the measured T for the two samples of different thickness. Another number very important to the glass evaluation is an approximate glass softening point. An ASTM method or a dilatometric measurement is impractical for small survey samples. A simple apparatus much like the one shown in Fig. 2.6 may be devised and easily built. One of the polished disk samples is placed in the bottom of the chamber. A thermocouple is placed inside next to the sample. Inert gas may be slowly circulated if needed. As the disk sample is heated and begins to soften, the glass rod in the center drops down, moving the indicator arm and signifying the softening point has been reached. The size of the weight, the weight of the rod, and the thickness of the sample are important variables. Calibration with known glasses should be carried out to support the results. Determining the glass forming compositions for a binary system is of course the easiest since you have only two elements. The results are then plotted on a composition percent straight line with glass or crystalline marked at each composition point on the line.

31

32

Chapter Two Weight

Inert gas

Quartz rod

Heater

Sample

Sample holder

FIGURE 2.6

Simple apparatus for measuring glass softening point.

For a three-component ternary system, many samples are required. Table 2.1 lists over 50 samples14 prepared in the evaluation of the Si-P-Te system, a system evaluated early in the exploratory program at TI. The 39 samples evaluated, identified by number, are plotted in their respective composition points in the compositional triangular diagram shown in Fig. 2.7. The glass forming composition region is designated to lie within the dashed lines. Again, note that the extent of this region is dependent on the quenching procedure as well as the composition. For example, quenching in a cool liquid would enlarge the area. The evaluation results indicated a system that was not promising. The glass forming region is smaller than that of the first system evaluated at TI, the Si-As-Te system.13 Comparison of the sizes of glass forming regions indicates differences in the glass forming tendencies of different element combinations. The conclusions reached

Chalcogenide Glasses

Sample Number 3

Atom % Si

P

Te

Softening Point (°C)

Remarks

20

20

60

190

Stable glass

12

25

25

50

Crystalline

15

40

20

40

Crystalline

16

30

20

50

Unstable glass

19

15

20

65

150

Stable glass, poor IR transmission

20

15

25

60

200

Stable glass, ~10% IR transmission

21

20

25

55

185

Stable glass, ~10% IR transmission

22

25

20

55

325

Stable glass, poor IR transmission

23

30

25

45

24

35

20

45

25

35

15

50

Unstable glass

26

30

15

55

Unstable glass

27

25

15

60

Unstable glass

28

20

15

65

250

Stable glass

29

15

15

70

180

Very stable glass, 10% IR transmission

30

10

20

70

Reacted violently with the atmosphere

31

10

25

65

Reacted violently with the atmosphere

32

10

30

60

Reacted violently with the atmosphere

33

15

30

55

Reacted violently with the atmosphere

34

35

25

40

Crystalline, unstable

35

40

15

45

Crystalline, unstable

36

40

10

50

Crystalline, unstable

37

35

10

55

38

30

10

60

TABLE 2.1 (Continued)

Unstable glass 385

Unstable glass

Crystalline, unstable 400

Unstable glass

Composition of Samples Used in the Evaluation of the Si-P-Te System14

33

Sample Number

Atom % Si

P

Te

Softening Point (°C)

Remarks

39

25

10

65

300

Stable glass, 10% IR transmission

40

20

10

70

200

Stable glass, 10% IR transmission

41

15

10

75

175

Very good glass, 35% IR transmission

42

15

5

80

160

Very good glass, 35% IR transmission

43

20

5

75

200

Very good glass, 20% IR transmission

47

25

5

70

250

Stable glass

48

30

5

65

Glassy

49

35

5

60

Glassy

50

40

5

55

Crystalline

51

30

0

70

Crystalline

52

25

0

75

Glassy

53

20

0

80

Glassy

54

15

0

85

55

10

5

85

Crystalline

56

10

10

80

Crystalline

375

Glassy

TABLE 2.1 Composition of Samples Used in the Evaluation of the Si-P-Te System14 (Continued) Si

50

36 37

49 48

51 52

43

54

42 55

Te

FIGURE 2.7 system.14

34

39

47

53

38

40 41

56

29

35

25

26 27

28

22

19

34 23

16 12

21

3

30

15

24

20 31

33 32

P

The glass forming composition diagram for the Si-P-Te ternary

Chalcogenide Glasses regarding glass forming tendency in the IVA-VA-VIA ternaries were

S > Se > Te As > P > Sb Si > Ge > Sn The reversal between As and P may be due to the fact that As forms bonds with Si and Ge while P does not.33 Efforts to form glasses with Sn were unsuccessful except in very low Sn concentrations.

Qualitative Evaluation of Compositions for Development For the Si-P-Te system, only one-third to one-half produced glasses of good quality, and those had softening points below 200°C. Disks were cut from the glass sample, and polished and evaluated relative to infrared transmission as a function of wavelength, and a qualitative estimate of the refractive index of each was determined. Figure 2.8 shows the results of this effort. Note that at this time, measurements were crude in comparison to today and could only be considered qualitative. Following this procedure developed in the exploratory program, seven ternary IVA-VA-VIA systems were evaluated during the threeyear period from 1962 to 1965. Results of the evaluation are given in Table 2.2. Each system was evaluated with respect to softening point, approximate refractive index, and infrared absorption in the two

60 Absorption coefficient (cm–1)

2.4

40

Si3P3Te14

N = 3.30

Si3P2Te15 Si3PTe14

N = 3.40 N = 3.45

20

0

FIGURE 2.8

(29) (41) (42)

0

4

8 12 Wavelength (µm)

16

20

Measured infrared transmission of some Si-P-Te glasses.

35

36

Chapter Two

Absorption

System

Max. Softening Point

Refractive Index

3 to 5m

8 to 14m

Si-P-Te

180°C

3.4

No

Slight

Si-Sb-Se

270°C

3.3

Yes

Yes

Si-Sb-S

280°C



Yes

Yes

Ge-P-Se

420°C

2.4–2.6

Slight

Yes

Ge-P-S

520°C

2.0–2.3

Very slight

Yes

Si-As-Te

475°C

2.9–3.1

No

Slight

Ge-As-Te

270°C

~3.5

No

Very slight

Ge-P-Te

380°C

~3.5

No

Very slight

TABLE 2.2 General Properties of the Best Infrared Transmitting Glasses from Each of the Ternary IVA-VA-VIA Systems

atmospheric windows of 3 to 5 µm and 8 to 14 µm. The Si-As-Te, Ge-As-Te, Si-P-Te, and Ge-As-Te systems were rated useful in both bands relative to transmission. The Si-Sb-S and the Si-Sb-Se systems produced glasses unstable and reactive with the atmosphere. Glasses with the highest softening points were Ge-P-S, G-P-Se, and Si-As-Te. Sulfur-based glasses begin to absorb strongly at wavelengths beyond 8 µm and are not useful in the 8- to 12-µm thermal window. The conclusion was that none of these systems promised to produce glasses meeting our original goal, with physical properties comparable to those of silicate-based optical glasses. Efforts were made to improve the glasses by blending two systems together over the full composition range. In this case, the system contained four elements rather than three. An example is the blending of the Si-As-Te ternary with the Ge-As-Te ternary forming Si-Ge-As-Te glasses. The only way to evaluate the usefulness of these glasses was to prepare them in high-quality batches up to 1 to 2 kg so that they could be characterized physically and optically in a more quantitative manner. Table 2.3 lists the glasses characterized and their individual results. Note the sulfur glasses are somewhat better physically than those based on Se and Te. However, they are not useful for the thermal window, the goal of the program. Figure 2.9 is a photograph of a large cast Si-GeAs-Te glass plate. Also shown are glass prisms to be used to measure the infrared refractive index quantitatively as a function of wavelength. Figure 2.10 shows an attachment built at TI for the Perkin Elmer 13 U spectrophotometer for performing the prism minimum deviation measurement in the infrared. The results are precise index numbers good to three to four decimal points. We will discuss this method in detail when the instrument used presently at AMI is described in Chapter 4. Figure 2.11 shows results obtained for two

Chalcogenide Glasses

Composition

Thermal Coefficient Softening Deformation of Expansion Hardness [in/(in . °C) ¥ (Knoop Point Refractive Point 106] (°C) (°C) Scale) Index

SiAsTe2

2.93

317

250

13

167

Si3Ge2As5Te10 3.06

320

284

10

179

GeAs2Te7

178

140

18

111

3.55

Ge3PS6

2.15

520

375

15

185

Ge7PS12

2.20

480

360

13

179

Ge2S3

2.30

420

360

14

179

Si6As4Te9Sb

2.95

475

350

9

168

TABLE 2.3 Physical Constants of Chalcogenide Glasses in This Program Prepared in Amounts Sufficient for Detailed Evaluation

FIGURE 2.9 Photograph of a large cast chalcogenide glass plate and four glass prisms fabricated for IR index measurements.

37

Chapter Two Bridgeport rotary table

M4

Slit S1

M5

M2

M3 Slit S2 Off–axis paraboloid

Spherical mirror

Detector M6

M1

Perkin–elmer 301 (or 13) infrared spectrophotometer

FIGURE 2.10 Infrared refractometer attachment for the Perkin Elmer 13 Spectrophotometer.

prisms of a Si-Ge-As-Te glass composition made from separate batches. The precise index measurements were used to calculate the bulk absorption coefficient as a function of wavelength. The absorption coefficient α is shown in the bottom curve and given in units of cm–1. The index differences between the two prisms were 0.0026 at 3 µm dropping to 0.001 at 10 µm. These are not bad results for the first time producing the glasses in large amounts, fabricating the prisms, and 6

Prism A 4

nA

3

Prism B nB

3.05

2

Absorption coefficient (cm–1)

5

3.10

Refractive index

38

1 αA 3.00

2

4

6 8 10 Wavelength (µm)

12

14

0

FIGURE 2.11 Precise infrared index results for two prisms of a Si-Ge-As-Te glass composition made from different melts.

Chalcogenide Glasses making the measurements. With a criterion, at this early stage, of an absorption coefficient of less than 1 cm–1, the Si-Ge-As-Te glass was judged good from 2.5 to 12.5 µm. The Si-As-Te glasses were judged good to only 9 µm, and the Ge-As-Te glasses good from 2.5 to 20 µm. Blending of two ternary systems was carried out for six combinations. The one that produced the most useful results was the Si-As-Te with the Ge-As-Te system. Table 2.4 lists the compositions prepared Sample No.

Composition

Softening Point (°C)

Hardness (Knoop)

239

Si6As8Te26

196

108.4

242

Si5GeAs8Te26

190

126.5

245

Si4Ge2As8Te26

124

126.5

248

Si3Ge3As8Te26

200

136.8

251

Si2Ge4As8Te26

190

127.0

253

SiGe5As8Te26

180

126.5

255

Ge6As8Te26

Crystalline

258

Si6As9Te45

160

108.4

260

Si5GeAs9Te45

136

105.8

261

Si4Ge2As9Te45

148

110.9

262

Si3Ge3As9Te45

146

108.7

263

Si2Ge4As9Te45

148

109.0

264

SiGe5As9Te45

150

113.4

265

Ge6As9Te45

162

113.7

240

Si5As5Te10

310

166.9

266

Si4GeAs5Te10

290

156.5

267

Si3Ge2As5Te10

293

179.0

268

Si2Ge3As5Te10

256

151.2

269

SiGe4As5Te10

Crystalline

241

Si7As5Te8

434

244

Si6GeAs5Te8

380

195.6

247

Si5Ge2As5Te8

394

198.6

250

Si4Ge3As5Te8

379

195.0

251

Si3Ge4As5Te8

Crystalline



— 207.8



TABLE 2.4 Blended Glasses Formed from the Ternary Systems Si-As-Te and Ge-As-Te

39

40

Chapter Two

400

40%

Softening point

Si7As5Te8

50%

300

Si5As5Te10 65%

200

Si6As8Te26 75% Si6As9Te45 100

0

20 40 60 80 Percent substitution (Ge for Si)

100

FIGURE 2.12 Substitution of Ge for Si in Si-As-Te glasses change in softening point.

with the measured softening point and Knoop hardness for each composition. Figure 2.12 shows the change in softening point of the individual Si-As-Te glass compositions as germanium is substituted for silicon. Note the softening points all decline when germanium is introduced. The chalcogenide glass plate in Fig. 2.9 shows the first glass plate cast at TI made from a blended Si-Ge-As-Te glass. The plate was polished and an antireflection coating was later applied.

2.5

General Physical Properties of Chalcogenide Glasses 2.5.1

Softening Points and Hardness

The higher the softening points, the harder the glass. Figure 2.13 shows the plot of measured hardness for about 100 compositions plotted against their measured softening points. Some of the glasses contained

Chalcogenide Glasses

500

Softening point (°C)

400

300

200 As2S3

100

100

200 Knoop hardness

300

FIGURE 2.13 Correlation of softening point and Knoop hardness for chalcogenide glasses.

four elements. Even with a softening point of 500°C, Knoop hardness was less than 250.

2.5.2 Thermal Coefficients of Expansion The higher the softening point, the smaller the thermal expansion coefficient. Results obtained from 30 samples are plotted in Fig. 2.14. The correlation is very general in part because the glasses measured are from different systems some with four elements. Many factors may affect results.

2.5.3

Density

The densities of selenium and tellurium glasses containing silicon, germanium, arsenic, and phosphorus are almost a linear function of the calculated average molecular weight of the glass composition.

41

Chapter Two

500

400

Softening point (°C)

42

300

As2S3 200

100

10 20 30 40 Thermal coefficient of expansion in (in · °C) × 106

FIGURE 2.14 Correlation of softening point and thermal expansion for chalcogenide glasses.

Figure 2.15 plots the results for 28 glass compositions. The densities for Te, Se, S, Si, and Ge are added for reference. Some of the samples were small in mass. The values obtained from large samples, the prisms and the cast plate, were given greater consideration in drawing the straight line. To check the validity of the straight line, densities for 15 samples of Ge-As-Se glasses reported in the literature34 were calculated and compared to reported values and found an average error in agreement of only –3 percent.

2.5.4

Molar Refraction

The apparent linear relationship between density and molecular weight suggests that other properties are additive and can be predicted. One such property is the refractive index. The refractive index is related to the molar refraction and molecular volume of a

Chalcogenide Glasses

Crystalline Te GeAs2Te7 prism

6.0 Crystalline As 5.5 Crystalline Ge 5.0

Density (g/cm3)

SiAsTe2 prism 4.5

4.0

Amorphous Se

3.5 As2S3 glass 3.0 Sulfur glasses Crystalline Si

2.5

Liquid S 2.0

P 0

FIGURE 2.15

20

40

60 80 100 Molecular weight

120

140

Density versus molecular weight for chalcogenide glasses.

substance. From the Lorentz-Lorenz equation,35 molar refraction is given by R=

N2 − 1 N 2 − 1 MW V= 2 N2 + 2 N +2 d

where R is the molar refraction, N is the refractive index at some nondispersive wavelength, and V is the molar volume equal to average molecular weight divided by the density d. For a nonpolar amorphous glass, molar refraction is almost equal to the molar polarization. Molar refraction has the units of volume and can be thought of as the additive sum of the volumes of each atom (or ion) in the molecule. Molar refraction is related to the radius of the individual molecule by R=

4 4 π A α = π Ar 3 3 3

where A is Avogadro’s number, α is the polarizability of the atom or ion, and r is the radius of the conducting sphere formed by the molecule.

43

44

Chapter Two This equation has been applied to the study of bonding in organic and inorganic compounds including oxide glasses.36 For a molecular compound of the form AxByCz, where x, y, and z are the atomic fractions of the constituents A, B, and C, the molar refraction becomes

R = xRA + yRB + zRC where RA , RB, and RC are the atomic (or ionic) refraction values resulting from their presence in the molecule. The approach applies well to the covalent bonded chalcogenide glasses so that single values for each element can be determined and used in many different glass compositions. The atomic refraction values should be close to the cube of their accepted covalent radii. Calculating directly from accepted covalent radii would yield low values because the atomic spheres are loosely packed. Amorphous selenium was chosen as the starting point in calculating atomic refraction values for use with chalcogenide glasses.Using available experimental data. The atomic refraction for selenium was calculated and used as a reference. The index wavelength chosen was 5 µm. The atomic refractions for silicon, germanium, phosphorus, arsenic, sulfur, and tellurium were calculated from the cube of their covalent radii and normalized to selenium. From these atomic refraction literature-derived values, the molar refractions for the 28 glass compositions used in the density plot of Fig. 2.15 were calculated and compared to the measured values. Agreement was ±4.1 percent. The results are given in Table 2.5. Another approach that yielded better agreement was to treat the glass formulas of atomic refraction values for glasses with different concentrations of the same elements as simultaneous equations and solve directly for the experimental atomic refraction values of each constituent element. When the 28 glass compositions were recalculated, the agreement with experimental values was ±1.1 percent. Table 2.6 lists the atomic refraction values determined from the literature and from solving the simultaneous equations. Values from glasses based on S, Se, and Te are given for comparison. An illustration of the worth of the method follows: The refractive index for chalcogenide glasses at 5 µm can be calculated within a few percent by using the density vs. molecular weight plot in Fig. 2.15 and the atomic refraction values in Table 2.6 to calculate molar refraction:

R = xRA + yRB + zRC Then solve for N from R = (N2 – 1)/(N2 + 2) × molecular weight/density. This procedure was applied to 20 As-Se-Te glasses reported by Jerger and Billian at Servo Corporation.5 The accurate values they reported and the values estimated agreed within +3 percent. The results are shown in Table 2.7.

Chalcogenide Glasses

Composition

R Calculated R Calculated Average % Literature R Error % Error Value Measured Value

PS4

7.36

8.49

+15.4

7.36

0

Ge3PS6

8.26

9.23

+11.7

8.27

+0.1

Ge2S3

8.90

9.30

+6.5

8.90

0

As2S3

9.44

9.42

–0.2

9.44

0

Se

11.55

11.51

–0.4

11.55

0

P-Se9

11.17

11.44

+2.4

11.31

+1.3

PSe4

11.35

11.35

0

11.06

–1.7

AsSe9

11.85

11.52

–2.9

11.62

–1.9

AsSe4

11.55

11.54

–0.1

11.68

+1.1

Si-Se9

11.65

11.31

–2.9

11.65

0

Ge16As47.3Se36.7

11.33

11.56

+2.0

11.36

+0.3

Ge15As45Se40

11.45

11.54

–0.3

11.35

–0.8

Ge3P3Se14

10.70

11.36

+6.2

10.70

0

Ge-Se9

11.23

11.49

+2.3

11.23

0

SiAsTe2

13.42

14.55

+8.4

13.53

+0.8

Si2PTe7

16.05

15.96

+0.4

15.21

–5.2

Si3PTe16

16.55

16.76

+1.3

15.77

+1.3

Si3As2Te5

13.70

14.43

+5.3

13.70

0

Si3As3Te4

12.95

13.74

+6.1

13.23

+2.2

Si2As3Te5

13.90

14.66

+5.5

13.90

0

GeAs4Te5

14.07

15.09

–7.3

14.63

+4.0

GeAs2Te7

15.95

16.47

+3.2

15.87

–0.5

Ge3P4Te13

15.83

15.90

+0.4

15.81

–0.1

Ge3As10Te7

13.40

14.03

+4.7

13.58

+1.3

GeAs10Te9

14.30

14.75

+3.1

14.52

+1.5

GeAs12Te7

13.65

14.05

+2.8

13.96

+2.3

Ge3As2Te15

16.25

16.77

+3.2

15.83

–2.6

Ge2As3Te15

16.15

16.79

+4.0

16.02

–0.8

Average

±4.1

TABLE 2.5 Molar Refraction Values of Chalcogenide Glasses

±1.1

45

R Calculated from Literature Element Values

R Calculated from Covalent Radii

Si

9.45

10.1

Ge

13.4

P

11.35 10.6∗

8.8

3.3

9.1

13.8

15.0

As

11.6†

12.5

11.0

12.2

11.6

12.2

17.05

17.8

S

7.95

7.85

Se

11.51

11.55

Te

18.55

18.21

R R Calculated Calculated for S for Se Glasses Glasses 12.5 9.7

R Calculated for Si-Te Glasses

R Calculated for Ge-Te Glasses

9.6

8.3

9.9

8.4 11.55

∗From P-Se4 glass. † From As-Se4 glass.

TABLE 2.6 Atomic Refraction Values for IVA, VA, and VIA Elements When Used in Chalcogenide Glasses

Servo No.

Composition

N at 5 µm

N Calculated

% Error

1

As38.7Se61.3

2.79

2.62

–6.0

2

As27.5Se72.5

2.65

2.59

–2.3

3

As40Se35Te25

2.88

2.90

+0.7

4

As40Se25Te35

3.07

3.06

–0.3

5

As30Se30Te40

3.08

3.11

+1.0

6

As20Se60Te20

2.74

2.80

+2.2

7

As35Se45Te20

2.90

2.71

–6.5

9

As45Se45Te10

2.77

2.75

–0.7

10

As25Se45Te30

2.91

2.93

+0.7

11

As30Se60Te10

2.76

2.71

–1.8

12

As10Se60Te30

2.73

2.89

+5.9

13

As20Se50Te30

2.84

2.94

+3.5

14

As20Se70Te10

2.65

2.68

+1.1

16

As35Se55Te10

2.83

2.72

–3.9

17

As30Se55Te15

2.82

2.76

–2.0

18

As25Se55Te20

2.80

2.81

+0.4

19

As20Se55Te25

2.64

2.84

+7.5

20

As15Se55Te30

2.78

2.92

+5.0

Average ±2.9% TABLE 2.7 Measured and Calculated Refractive Index Values for Servo As-Se-Te Glasses5

46

Chalcogenide Glasses

Dielectric Constant

Glass

Frequency (cps)

Resistivity (Ω . cm)(300K) 5 × 1010

Ge15As15Se70 Si15Sb15S70

9.6 × 107

Ge15P15Se70

9.3 × 1010

Si15Sb35S50

14

100

2 × 109

Si6As9Te45

5 × 105

Ge2As3Te15

2 × 107

Si3Ge2As5Te10

24

1 kc

1 × 108

Ge3P S6

9 × 109

GeAs4Te5

5 × 105

Si4As3Te3

5 × 109

GeAs2Te7

2.8 × 104

TABLE 2.8 Electronic Conduction of Some Chalcogenide Glasses

2.5.5

Electrical Properties

It was mentioned earlier in Chap. 1 that chalcogenide glasses are electronic conductors and their properties have been the subject of intense study, but not in this program. Early on at TI, it was found that some glasses containing Te and Sb could become good conductors with low resistivity but poor infrared transmission. Some electrical measurements carried out on 11 compositions are listed in Table 2.8. From the values, it is clear that the glasses used optically may be called high-resistivity semiconductors ranging in values from 104 to 1010 ohm ⋅ cm at room temperature. The two measured dielectric constants were high. What is not shown in the table is the fact that these glasses are electronic conductors with very low mobility for their electrons or holes involved in the conduction process. The poor mobility is the result of the nature of glass. All glasses are disordered solids.

2.5.6

Physical Strength

At this point in time, the large samples with flawless physical quality required for meaningful measurements were not available. Some attempts to measure the tensile strength breaking fibers were made but with poor results. Most all the fibers had surface flaws. Ultimate tensile strength ranged from 500 to 1000 psi for three samples judged flawless. Later, we will discuss physical strength of glasses based on rupture modulus tests and the determination of Young’s modulus and the shear modulus from acoustical measurements.

47

48

Chapter Two

2.5.7

Softening Points

Softening point decreases with increasing molecular weight.

S > Se > Te P > As > Sb Si > Ge > Sn

2.6

Chemical Bonding in Chalcogenide Glasses 2.6.1

Composition Location in the Glass Forming Diagram

For ternary systems, glass forming compositions are experimentally found to exist within an area designated within a triangular composition diagram. We have not mentioned a factor very important in interpreting the chemical bonding in the different regions—stoichiometry. Figure 2.16 presents the results16 determined for the glass forming region in the Ge-Sb-S system. Note the stoichiometric compound GeS2 is designated as well as the stoichiometric compound Sb2S3. The compounds are stoichiometric because their atomic ratios are correct for Ge with a valence of +4 and S with a valence of −2, while Sb has a valence of +3 with again S with a valence of –2. A line is drawn in the diagram connecting the two stoichiometric compounds. Any glass composition along that line is stoichiometric because the compounds’

Ge

Glass Two phase glass Crystal

GeS2

Sb

S Sb2S3

FIGURE 2.16 The glass forming composition diagram for the Ge-Sb-S system.

Chalcogenide Glasses atomic ratios are correct. Now, chemical bonds Ge-S and Sb-S are thermodynamically favored, from a free energy of formation standpoint, over S-S bonds. On the sulfur-rich side of that line, there is more than enough sulfur to satisfy the bonding requirements of both Ge and Sb. The remaining sulfur is bonded to other sulfur atoms in chains or rings. However, at the stoichiometric line, all the sulfur is bonded to either Ge or Sb. There are no longer S-S primary bonds. Across the line in the metallic rich areas, there is not enough S to go around. The free energy of formation for Ge-S is greater than that for Sb-S. Ge will use up its share of S first. But well away from the line we may expect to find Ge-Sb bonds, Ge-Ge bonds, and Sb-Sb bonds. The Ge-S bond has a high enough energy level that in binary form it can transmit visible light. The Ge-Ge, the Ge-Sb, and the Sb-Sb are all metallic and do not transmit visible light. Figure 2.17 is a diagram16 depicting transmission in the visible band for Ge-Sb-S glasses as a function of sulfur content. When the composition contains less than 55 percent sulfur, visible transmission is lost because metallic bonding becomes appreciable. This type of discussion can be applied to all the IVA-VA-VIA ternary systems regarding the bonds formed. In the chalcogen-rich area, the metallic elements bond to their share of the chalcogen. Chalcogen-chalcogen bonds exist. Across the stoichiometry line, after all the chalcogen is used up, metal-metal bonds will have to form. The change in the bonding accounts for the variation in physical and optical properties for glasses formed within the system. Visible light 80

Atom percent sulfur

70

60

50 1.06 µm YAG designator

40

0 0.2

0.4

0.6

0.8

1.0

1.2

1.4

Absorption edge wavelength location (µm)

FIGURE 2.17 Absorption edge wavelength location as a function of sulfur content location in Ge-Sb-S glasses.

49

Chapter Two

2.6.2

Molecular Vibrations of Constituent Atoms

Some insight into the molecular nature of the chalcogenide glasses may be gained by the use of some standard methods. One method already mentioned in Chap. 1 is far infrared reflection spectroscopy to observe the strong Restrahlen like bands due to the constituent atom pairs. The word like is added because the term is normally used to describe infrared reflection for crystalline materials, not glasses. The greater the ionic character of the bond formed between the atom pair, the more intense the absorption which in turn increases the magnitude of the reflection. From inspection of the shape of the curve, one can deduce the frequency37 of the vibration between the two atoms to a fair degree of accuracy. Of course, if the sample can be ground thin enough and polished again, the absorption frequency may be directly measured through transmission. Absorption results may also be obtained by powdering the material and pressing into a pellet using KBr or TlBr and measuring IR transmission. Another way, and the most accurate, is to use a Raman spectrophotometer which directly measures the frequency of all the intense vibrations. Keep in mind, such instruments were not readily available at the time of the results of the program being described. Figure 2.18, also seen in Chap. 1 as Fig. 1.7, shows the measured reflectivity for several chalcogenide glasses. The curves for the binary glasses As2S3 and Ge2S3 will yield the harmonic oscillator frequencies for the As-S bond and the Ge-S bond. The other two glasses are three 50

Ge15P15Te70

40

% Reflectivity

50

Si10As10Te2O 30

As2S3 20 Ge2S3 10

0

0

10

20

30 40 Wavelength (µm)

50

FIGURE 2.18 Far infrared Restrahlen-like reflection bands of some chalcogenide glasses.

60

Chalcogenide Glasses component glasses and will yield the harmonic oscillator frequency for the dominant pair which in this case comprises Si-Te and Ge-Te. The other bond pairs absorb but not with the intensity required to produce a reflection band. Also, the intensity is affected by the concentration of the element in the glass composition. The optical constants are interdependent. That is, the refractive index is really a complex number N = n – ik, where n is the real part of the refractive index and k is the imaginary part of the refractive index, sometimes called the extinction coefficient. The bulk absorption coefficient α can be calculated from α = 4πk/λ, where λ = wavelength in centimeters. Reflectivity R is calculated from R=

(n − 1)2 + k 2 (n + 1)2 + k 2

In the transparent region, k is very small and is omitted in the calculation. However, in the region of the Restrahlen band, it becomes large, even the dominant term. The curves in Fig. 2.18 show the expected shape. The peak of reflectivity, the maximum absorption wavelength, and the wavelength for the harmonic oscillator do not coincide because of the interrelationship of the optical constants. The wavelength of the harmonic oscillator for each bond pair and the maximum absorption were determined, when possible, by using the inspection method described by Moss.37 The values needed for the calculation are the magnitude of maximum reflectivity, the wavelength of maximum and minimum reflection, and the short wavelength refractive index. The calculated results found from the curves in Fig. 2.18 and for a number of other samples are shown in Table 2.9. In some cases only absorption results were available. From the results, we see that binary glasses are straightforward, yielding their oscillator frequency, As-S, Ge-S, Ge-Se, As-Se. A small change is observed when a third element is present. The absorption of the third element is not intense enough to produce a second band whether due to the concentration or the ionic character of the bond. At the very least, the different mass of the atom when coupled to the primary structure produces a frequency change. As an example, compare the oscillator frequency for the Ge-S binary and in the ternary Ge-S-Te. Tellurium is an atom much heavier than sulfur which lowers the frequency of vibration. The force constant for each atom pair may be calculated from 1/2

νo =

κ 1 ×  2 π C µ 

where νo = wave number of harmonic oscillator frequency C = speed of light κ = force constant µ = reduced mass

51

52

Chapter Two

System

Constituent Atoms Involved

Wave Number of Calculated Harmonic Wavelength Oscillator of Reflection Frequency no (cm–1) Max. (mm)

Wave Number of Calculated Maximum Absorption Frequency nmax (cm–1)

As-S

As-S

32

307

Ge-S

Ge-S

27.5

349

360

[370] T1Br

Ge-S-Te

Ge-S

28

342

355



Ge-P-S

Ge-S

27

358

366



Si-As-Te

Si-Te

31

307

322

[323] T1Br

Ge-P-Te

Ge-Te

50

196

205

[212] T1Br

Si-Se

Si-Se



382



[392] T1Br

Ge-Se

Ge-Se

40

234

250



As-Se

As-Se

44

217



[226] KBr

P-Se

P-Se



350



[363] KBr

P-S

P-S



525



[535] KBr

Ge-As-Te

Ge-Te

50

196

205



Ge-P-Se

Ge-Se

39

244

255



Ge-As-Se Ge-Se

41

233

247



P-S

14.7

675



[710] KBr

P=S

291

[313] T1Br

TABLE 2.9 Wave Number of the Harmonic Oscillator for Glass Bond Pairs and Wave Numbers for Maximum Absorption Calculated from Far IR Reflection and Absorption Measurements

If it is assumed that the vibration between the atoms is a simple diatomic vibration, an estimate of the equilibrium interatomic distance can be calculated from the force constant by using Gordy’s rule.38 3/4

X X  Gordy ’s rule : κ = 1 . 6N  A2 B   d AB  where

+ 0 . 30

κ = force constant (units dyne cm–1 × 10–5) N = bond order = 1 in this case XA, XB = Pauling electronegativities for A and B dAB = equilibrium distance between A and B

The interatomic distances for nine atom pair vibrations identified in the manner described were calculated and compared to the sum of

Chalcogenide Glasses

dÅ from Addition Covalent Radii

D

Bond

no cm–1

dÅ Calculated (Gordy’s Rule)

Ge-S

349

2.29

2.24

+0.05

Ge-Se

234

2.56

2.38

+0.18

Ge-Te

196

2.61

2.57

+0.04

As-S

291

2.87

2.21

+0.66

As-Se

217

2.89

2.35

+0.54

Si-Te

307

2.35

2.46

–0.11

Si-Se

382

2.15

2.27

–0.12

P-S

525

2.02

2.08

–0.06

P-Se

350

2.42

2.22

+0.20

TABLE 2.10 Interatomic Bond Distances Calculated Using Gordy’s Rule Compared to Sum of Covalent Radii

covalent radii for each of the atoms in the bond pair. The results are shown in Table 2.10. Both Ge and Si are probably in tetrahedron structures where bonds are symmetric and equal. The sum of covalent radii agrees quite well with the calculated value when a bond order of 1 is assumed and used in Gordy’s rule. However, the agreement between the calculated and the addition of covalent radii is not as good for As-S and the As-Se. Their structures are probably pyramidal, which does not fit the simple diatomic model. This fact suggests that a more detailed analysis of the infrared vibrations may yield information concerning the molecular arrangements of the constituent atoms. The molecular units may be thought of as individual molecules free to absorb and vibrate independent of their nearest neighbors and surroundings. In the close association of the solid environment, the vibrations will decrease in frequency generally. Since there is no uniform orientation from molecule to molecule, symmetry considerations used in analyzing the vibrational spectra of crystalline materials do not apply. In free molecules all vibrational modes are infrared active if a change in the electric dipole occurs due to the vibration. Some normal vibrations not infrared active can be observed by the Raman effect. The simplest approach is to assume that molecular units may involve three atoms and the structure may be X-Y2 linear or X-Y2 nonlinear. For four atoms, the structure may be X-Y3 pyramidal. For five atoms, the X-Y4 structure would likely be tetrahedral. The equations for the normal mode vibrations of these molecules are found in

53

54

Chapter Two Herzberg.39 The expressions involve atomic masses, bond lengths, bond angles, and two force constants k and kδ. The kδ is a measure of the restoring force opposing a change in the angle between the two valence bonds. The magnitude is about 10 percent of the k value and was assumed to be such in all the calculations. Interatomic distances were taken to be the sum of the covalent radii. With the equations and using Gordy’s rule, the vibrational frequencies for four molecular gases typical of the four molecular configurations considered were calculated and compared with observed frequencies. The four gases were CO2, SO2, AsCl3 and SiCl4. Agreement between observed and calculated was poor except for the AsCl3, X-Y3 pyramidal case. A method better suited for polyatomic force constant prediction was developed by Somayajulu.40 This method utilizes the elemental covalent force constants and electronegativity to predict force constants. The expression used is

KAB = (KAAKBB)1/2 + ∆ where ∆ = (XA − XB)1/2 Tables for elemental force constants are given by Somayajulu.40 Values for single, double, and triple bonds are given including constants for hybridized orbitals such as sp3, the tetrahedral structure. For silicon and germanium two force constants are given, single and sp3 tetrahedral. Both the X-Y2 linear and nonlinear molecules have three vibrational modes. In both cases the ν1 wave number corresponds to the symmetric stretching vibration, ν3 corresponds to the unsymmetric stretching mode, while the ν2 frequency is the bending mode. The ν1 modes are not infrared active because of the molecule symmetry but can be seen in Raman spectra. All four of the pyramidal molecule modes are infrared active. The calculated frequencies for pyramidal molecules in close agreement with observed has been mentioned before. The observed frequencies for Si-Te, Si-Se, Ge-Te, and Ge-S in each case agree very well with the ν1 mode frequency calculated for the nonlinear X-Y2 symmetric molecule. The vibrations for the As-S and As-Se molecules are quite different. They both match the ν1 mode of the pyramidal structure. The absorptions were found in binary glasses but not observed when a group IVA element was present. Surprisingly, the P-S and P-Se vibrations fit the X-Y2 nonlinear configuration rather than the pyramidal configuration. The differences may be related to the chemical differences between arsenic and the other VA elements phosphorus and antimony. The differences were pointed out while explaining glass forming tendencies. Also, we should keep in mind the change in bonding that will

Chalcogenide Glasses occur when compositions move from the chalcogen-rich region through the stoichiometric line into chalcogen-deficient compositions. No doubt, in this investigation or one similar, Raman spectra would have been beneficial in trying to untangle observed frequencies as related to structures. Later investigations using Raman results have been reported.41

2.6.3

Mass Spectrometric Investigation of Bonding in the Glasses

Chalcogenide glasses are made from volatile elements. An investigation using a mass spectrometer equipped with a Knudsen cell will yield information from emitted species concerning the types of bonds present and their relative stability. The Knudsen cell has a small hole in the top which allows vapors, under equilibrium conditions with the heated sample, to flow into the Bendix time of flight (TOF) mass spectrometer for analysis. Ideally, the partial pressure of a constituent follows Raoult’s law35 which states the partial pressure of species A (PA) is equal to the atomic fraction of A (XA) times the pressure of pure A (PA0) at that temperature. Deviation from this value indicates bonding of A in the solid or liquid. Measuring the pressure of a species as a function of temperature yields thermodynamic information that can be related to the binding energy of the species in the solid or liquid phase. The slope of a plot of ln PA versus 1/T yields a differential heat of solution for species A in the solid or liquid. A change in the slope over a temperature range will indicate

Vapor Species

Appearance Temperature (°C)

Si15Te85

Te

386

24 kcal

173

Si15As15Te70

As

278

35

207

Te

377

18

Si15As45Te40

As

300



292

Si30As15Te55







359

Ge10As20Te70

As

262

28

178

Te

386

34



Ge15As45Te40

As

233

36

300

∆H

Softening Temperature (°C)

TABLE 2.11 Detected Vapor Species from Heated Chalcogenide Glasses

55

Chapter Two a change in bonding within the solid or liquid. So the instrument identifies the chemical nature of the vapor species, the temperature at which it appears, and the amount with temperature change. To ensure the Knudsen cell would function as expected, it was calibrated using pure arsenic. The value of ∆HV obtained for sublimation of arsenic was 31.2 kcal which matches the accepted value of 31 kcal.42 The temperature range of operation was 25 to 500°C, low enough to ensure equilibrium conditions inside the Knudsen cell were maintained. The appearance temperature of each species was noted and a heat of vaporization determined when possible. A summary of results is presented in Table 2.11. The heats of vaporization given are based on initial slopes. Note that in the glass Si30As15Te55 there was no vapor species detected up to 500°C, well above its softening point, which is very unusual. The low-silicon high-tellurium glass showed only tellurium at 386°C, well above the softening point. The low-As, low-silicon glass gave off As and Te vapors. The high-As glass emitted As vapor in large amounts. The high softening Si-As-Te glass gave off no vapors. The hightellurium Si-As glass showed As and Te emission. The Ge-As-Te glass emitted only As vapors. Figures 2.19 and 2.20 illustrate the differences between two Ge-As-Te glasses, one high Te and one high As. High heats of vaporization, greater than for pure As, indicate strong bonds being formed in the glass. Only one glass was so stable in its bonding that it emitted no vapors. All the others emitted Te, As, or

100

As

80 Relative intensity

56

As4

60

As2

40

20

As3 Te

0 60

100

140

180 M/E

220

FIGURE 2.19 Mass spectrum of glass Ge10As20Te70.

Te2 260

300

Chalcogenide Glasses

100

Relative intensity

80

As4

As

60

40 AsO

As2

20

0 60

As3

100

140

180

220

As3O4

260

300

As4O6

340

380

M/E

FIGURE 2.20

Mass spectrum of glass Ge15As45Te40.

both. There were no three-component molecules detected in the vapor of any of the glasses. There were no vapors containing Si or Ge. Four forms of As vapor were detected: As, As2, As3, and As4. The equilibrium of As vapor above high-arsenic-containing glasses becomes complicated. It appears that in compositions containing high concentrations of arsenic in the low-chalcogen regions, the arsenic is not bonded in the glass network, only captured. Similar results were observed in Ge-P-S glasses with the evolution of phosphorus molecules on quenching the melt, resulting in explosion of the quartz vials. In studies carried out on Ge-Sb-Se glasses, the major vapor phase species was GeSe between 450 and 550°C. The heat of vaporization measure was 44.5 kcal. At 575°C, GeSe disappeared and Sb appeared at the melting point of Sb2Se3. Also note that the appearance of Te in Si-As-Te glasses and Ge-As-Te glasses corresponds roughly to the melting point of As2Te3. Such data are vital when heating and casting glasses in an open system.

2.6.4

X-ray Radial Distribution Analysis of Chalcogenide Glasses

It is well known that the molecular structure of crystalline compounds may be determined by X-ray diffraction analysis. What is not well known is that application of the method will yield information concerning atomic nearest neighbors sometimes even second-nearest neighbors of amorphous solid materials. Debeye43 pointed out that

57

58

Chapter Two

f1 f1 Si–Si

196

Si-As

462

Si-Te

730

As-As

1040

As-Te

1664

Te-Te

2700

Ge-Ge

1020

Ge-As

1060

Ge-Te

1760

Radial Distribution Areas for Si-As-Te and Ge-As-Te Glasses RI (Å)

RII (Å)

RI: RII

Si Te4

2.62

4.14

1:8

Si15 As15 Te70

2.58

4.12

1:12

Si15As45Te40

2.52

3.95

1:5

Si30As15Te55

2.50

4.12

1:4

Ge15As45Te40

2.50

4.02

1:4

Note: RI and RII are distances for nearest and second-nearest neighbor interactions from the radial distribution function. RI : RII is the area ratio between nearest neighbor peak and second-nearest neighbor peak.

TABLE 2.12

Relative Scattering Power between Various Atomic Interactions

one or two broad, diffuse diffraction bands were produced by liquids, glasses, resins, and unoriented polymers. The method was applied to Si-As-Te and Ge-As-Te glasses. X-ray scattered intensity measurements were taken using a standard Norelco wide-range goniometer. The relative scattering power for possible atomic pairs was calculated and is shown in Table 2.12. The radial distribution functions were calculated and plotted for each of glass systems SiTe4, Si15As15Te70, Si15As45Te4, Si30As15Te55, and Ge15As45Te40. All the radial distribution function curves show maxima at R values less than 2 Å which are necessarily false. The curve for SiTe4 is shown in Fig. 2.21. The area ratios RI:RII yield the most useful information. The results for the glasses studied are found in the lower portion of Table 2.12. In the case of SiTe4 glass, the 1:8 ratio can only be explained if RI consists of as many Si-Te bonds as possible with excess Te forming Te-Te bonds with RII consisting of Te,Te interactions. The Si-Te interactions have only one-fourth the scattering power of the Te-Te. The structural interpretation is that Si-Te bonding in Si-Te glasses is nonlinear consistent with the infrared assignment of X-Y2 molecules for Si-Te and

Chalcogenide Glasses 20.0

4.14

18.0 16.0 14.0 12.0 10.0

4π r 2 ρ0 – 4π r 2 ρ

8.0 6.0 4.0 2.62

2.0 0.0 –2.0 –4.0 –6.0 –8.0 –10.0 –12.0

–14.0 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 5.2 5.6 6.0 R (Å)

Radial distribution function of SiTe4 glass.

FIGURE 2.21

Ge-Te glasses. The X-ray results did not support the existence of Si-Te4 tetrahedral molecules which one would expect to be present.

2.6.5

Conclusions from the TI Exploratory Programs of 1962 to 1965

1. Seven ternary IVA-VA-VIA glass forming systems were investigated in this study. The Si-As-Te, the Ge-As-Te, and the GeP-Te glass systems showed the best infrared transmission in the 8- to 14-µm region. Attempts to form glasses using Sn or containing B failed. Silicon formed an unstable bond with selenium with a tendency to react with water to form hydrogen selenide. Glasses containing four elements were formed by combining the Si-As-Te glasses with the Ge-As-Te glasses. 2. The chemical bonding and thus the properties change with compositions within the glass forming region. The extent of

59

60

Chapter Two the glass forming region is dependent upon which elements are selected and the number of binary compounds they form with one another. 3. The chalcogenide glasses are characterized by covalent bonding. The molar refraction approach can be used to predict the refractive index of a glass using the covalent radius of each constituent atom, its atomic fraction in the glass, and the predicted density. 4. Glasses containing IVA elements Si and Ge are harder and stronger than those based more on VA elements P, As, and Sb. In some areas of the glass forming regions, excess P or As exists as free molecules which are emitted as such when the glass is heated. In ternary systems, no vapor molecules containing all three elements were observed. 5. The goal of finding chalcogenide glass compositions with physical properties comparable to those of oxide optical glasses was not reached and appears unlikely to be attained using the IVA-VA-VIA elements.

2.7

Chalcogenide Glasses Containing Transition Elements44 At this time, it was concluded that the chalcogenide glasses evaluated were never going to meet the window requirements of an airborne infrared optical system. Elements other than those in IVA and VA groups would have to be used in the glass composition. These must be elements with lower electronegativities and which form stronger chemical bonds with chalcogens. These elements can form multibonds, valences of +3 or +4, and form more than one stoichiometric compound with chalcogens. Titanium (Ti) and zirconium (Zr) from group IVB and vanadium (V) from group VB were selected. The crystalline chalcogenide compounds of these elements have melting points in excess of 1200°C. A high melting point ensures a low-viscosity melt and thus a homogeneous mixture. The methods previously used never exceeded 1000°C so a new approach must be developed. Basically, either an open or a closed system may be used for high-temperature compounding of materials that contain volatile constituents. In the open system the reactants are melted so rapidly that a homogeneous melt is obtained before an appreciable portion of the volatile constituent is evolved. The open method is simple and rapid. In the closed system, the reactants are sealed in a vial and slowly raised to a compounding temperature. With this system, the beginning composition is maintained. However, it is difficult to find materials that can withstand the high temperatures and resulting vapor pressure. The open system was tried, first concentrating on placing the reactants in recesses in the water-cooled copper plate and using the

Chalcogenide Glasses

To welder power supply (±)

Glass window

Ar in 1/2 Ar ATM.

Samples Copper plate

Chill water in

H2O

W tip Arc Ti Water out

To welder power supply (±)

FIGURE 2.22

Arc-melter reactor.

arc directly to form a melt. Figure 2.22 shows a diagram of the arcmelter reactor. Notice in the diagram an argon atmosphere was used to prevent oxidation of the reactants. Reactants were badly scattered. Pressing reactants into pellets using organic binders did not help. Next, graphite containers were used to contain the reactants by using graphite lids and then some made of tungsten. Only partial melting occurred. The graphite containers were placed on small graphite rods to thermally isolate the chambers. Complete melting was obtained with long arcing but with great loss of Te as vapors which changed the composition considerably. Mixtures tested were Ti-Si-Se, Ti-Ge-Se, TiGe-Te, Ti-Te-Se, and Ti-Se-S. Formation of Ti-Si2 or Ti-Ge2 from the elements using the arc was easy to accomplish. However, when they were brought in contact with molten mixtures containing S, Se, or Te, a violent evolution of the chalcogen occurred. The extreme stability of Ti-Si and Ti-Ge bonds is believed to be the cause of the excessive loss of the chalcogens. For this reason attention was turned to Ti-V based compositions that had lower melting points than the Ti-Si or Ti-Ge systems. However, attempts with the Ti-V-Te compositions produced similar results. No attempts were made using Zr in place of Ti. The chemistries of the two elements were very similar. The open system was abandoned after 67 attempts with no real success. The last attempt

61

62

Chapter Two failed even though reactants used were known to form a stable glass. The method failed.Attention turned to the closed system. A diagram of the system used is shown in Fig. 2.23. After a few attempts with unsupported quartz vials failed, all samples were placed in evacuated, sealed quartz vials that were supported in chambers made from graphite or BN. The sample was lowered into the bottom chamber to a distance where the thermocouple fit into a recess in the bottom of the BN/graphite support chamber all inside the hollow SiC heating element. After everything is in place, the entire system, upper and lower chambers, is evacuated. When the desired reaction temperature is reached and maintained for a period of time, the sample is ready for quenching. The sample is pulled up into the upper chamber. The flap valve between the upper and lower chambers is closed. The pump valve is closed to maintain the vacuum in the lower chamber to avoid heat shocking the SiC heating element. Air is then let into the upper chamber to aid in the quench of the sample. The quench rate is very rapid, estimated to be 5 to 10°C/s. After cooling the sample is removed through the top of the upper chamber. Using this procedure, melt temperatures of up to 1700°C were reached and held. First attempts concentrated on making a glass from the Ti-V-Te system.

FIGURE 2.23

Closed system reactor.

Chalcogenide Glasses Altogether there were 30 attempts. The composition of Ti15V15Te70 was chosen as the most likely to succeed. Figure 2.24 shows photographs of the results with that composition heated to 1300 to 1600°C. Notice that only at 1600°C were there signs that a melt had formed at the bottom of the vial. Obviously a higher temperature would be required. Raising the temperature to 1700°C and holding it longer produced homogeneous melts that

(a)

(b)

(c)

FIGURE 2.24 Photographs of the results from attempts to form glass from the composition Ti15V15Te70. (a) Reactor temperature 1300°C, (b) reactor temperature 1500°C, and (c) reactor temperature 1600°C.

63

64

Chapter Two cooled to crystalline solids. Photographs of the results are shown in Fig. 2.25. The solid was different in composition because Te vapor condensed on the walls of the vial. The true composition could be calculated by weighing the lost Te. For three runs the final compositions were calculated to be Ti30V30Te40, Ti23V23Te54, and Ti11V11Te78.

(a)

(b)

(c)

FIGURE 2.25 Ti5V15Te70. (a) Sample no. 95 reactor temperature 1700°C, (b) sample no. 96 reactor temperature 1600°C for 2 h, and (c) sample no. 97 reactor temperature 1600°C for 1 h.

Chalcogenide Glasses It was decided to use elements other than V with Ti to reduce the melt temperature. Ni and Ge were used along with Se for Te. The incidence of explosions increased. And still no glasses formed from homogeneous melts. Compositions containing Ti were abandoned. Perhaps Ti glasses did not form because the Ti-Te formation broke down any Te-Te amorphous chain-based structure. The coordination number for Ti is perhaps 6 or 8 Te atoms at the high melt temperatures. Similar considerations exist for the use of V or Zr. The net result is that crystallization occurs because of the decrease in viscosity of the melt. The need for a coordination number of 4 to form glasses is again supported by the results. Attempts to form chalcogenide glasses using Ni and Ge with Se and S were carried out with melt temperatures of 1000 to 1200°C. First appearance of the samples was that of a homogeneous, single-phase glass. A photograph of the results using a Ni-Ge-Se composition is shown in Fig. 2.26. Unfortunately, this was not the case when the

FIGURE 2.26

Results from a Ni-Ge-Se composition.

65

66

Chapter Two

Amorphous glass

Crystalline (metallic-like) solid

(a) Glass outer shell

Amorphous glass Crystalline (metallic-like) solid

(b) Layered glass

FIGURE 2.27

Configuration of two phase samples.

sample was sliced for evaluation. As shown in Fig. 2.27a, the outer shell was an amorphous glass (GeSe) while the inside was a secondphase crystalline (NiSe) solid. Other samples represented in Fig. 2.27b were layered where the amorphous lower-density glass was on top of a denser crystalline phase solid. Similar results occurred with Ni-Ge-Te, Ni-Ge-S, and Ni-Ge-Se. The use of Zn and Mn with Ge in Zn-Ge-Se and Mn-Ge-Se did produce glasses. Compounding temperatures were 1200 to 1300°C. Softening points of the glasses were around 300°C. Their appearance and infrared transmission were similar to those of other Ge-Se glasses. The Te-based compositions Mn-Ge-Te, Ni-Zn-Te, Ni-Ge-Te, and Zn-Ge-Te were prepared and compounded at 1300°C. All had the same metallic luster and were very crystalline inside. Photographs of samples from three of the systems are shown in Fig. 2.28. Table 2.13 summarizes the results obtained for all compositions attempted using the closed system.

2.8

Discussion of Results This effort was based on the assumption that a chalcogenide glass could be formed using elements known to form high melting compounds if the reactants could be heated hot enough to form a melt

Chalcogenide Glasses

(a)

(b)

(c)

FIGURE 2.28 Photographs of tellurium samples. (a) Ni-Zn–Te, (b) Zn-Ge–Te, and (c) Mn-Ge-Te.

67

68

Chapter Two

System

Homogeneous Melt Obtained

Glass

Remarks

Tellurium Compositions Ti-V-Te

Yes at 1600–1700°C

No

Dense, hard, crystalline solid

Mn-Ge-Te

Yes at 1300°C

No

Crystalline solid, metallic appearance

Ni-Zn-Te

Yes at 1325°C

No

Crystalline solid, metallic appearance

Ni-Ge-Te

Yes at 1300°C

No

Crystalline solid, metallic appearance

Zn-Ge-Te

Yes at 1300°C

No

Crystalline solid, metallic appearance

Ti-Ni-Te

No at 1500–1600°C



Porous, crystalline

Ti-Si-Te

No at 1350°C



Porous, crystalline

Selenium Compositions Ni-Zn-Se

Yes at 1225°C

Yes

Some infrared transmission, low softening point

Mn-Ge-Se

Yes at 1300°C

Yes

Low infrared transmission, contains crystallites, softening point ~ 290°C

Zn-Ge-Se

Yes at 1200°C

Yes

Low infrared transmission, contains crystallites, softening point ~310°C

Ni-Ge-Se

Yes at 1200°C

Yes

Two-phase, Gerich glass, Ni-rich crystalline phase

Ti-V-Se

No at 1400°C



Porous, crystalline

Ti-Ge-Se

No at 1400°C



Porous, crystalline

Yes

Ge-rich glass on top of Ni-rich crystalline phase

Sulfur Compositions Ni-Ge-S

Yes at 1000°C

TABLE 2.13 Results of Attempting to Compound High-Temperature Chalcogenide Glasses Using the Closed System Method

Chalcogenide Glasses before quenching. The transition elements titanium and vanadium would be paired with silicon and germanium in sulfur-, selenium-, and tellurium-based compositions. It was found that an open system based on an arc welder would not work because the chalcogens were immediately evolved. A closed system was devised in which the ingredients were sealed in quartz vials supported by cylinders made from BN or graphite. Melt temperatures of 1200 to 1700°C were reached. It was found that Ti-Te, Ti-Se, and Ti-S bonds that were formed were so strong that an amorphous chalcogen chain-ring structure could not form. Homogeneous melts at high temperatures did form and were quenched, but the results were all crystalline. In place of Ti and V, the other elements Zn, Mn, and Ni were used with Ge. Some glasses with low softening points that transmitted infrared did form. In other cases, two-phase glass and crystalline materials formed. No tellurium-based glass was formed. No glass comparable to oxide glasses resulted.

References 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.

18. 19. 20. 21. 22.

R. Frerichs, Phys. Rev. 78, 643 (1950). Rudolph Frerichs, Opt. Soc. Am. 43, 1153 (1953). C. Schultz-Sellack, Ann. Physik 139, 162 (1870). W. A. Fraser and J. Jerger, J. Opt. Soc. Am. 43, 332 (1953). C. J. Billian and J. Jerger, Contract No. Naval Office of Research-3647(00), January 1963. J. Jerger, Contract No. Air Force 33(657) 8560, June 1963. J. Jerger and R. Sherwood, Contract No. Naval Office of Research-4212(00), August 1964. The Structure of Glass, vol. 2, Proceedings of the Third All Union Conference on the Glass State, 1959, Consultants Bureau, New York, 1969. S. Nielsen, Infrared Phys. 2, 117 (1962). J. A. Savage and S. Nielsen, Phys. Chem. Glasses 5, 82 (1964). J. A. Savage and S. Nielsen, Phys. Chem. Glasses 7, 56 (1966). J. A. Savage, Infrared Optical Materials and Their Antireflection Coatings, Adam Hilger Ltd., Bristol and Boston, 1985. A. R. Hilton and Maurice Brau, Infrared Phys. 3, 69 (1963). A. R. Hilton, Naval Office of Research 3810(00), September 1965. A. R. Hilton, N00014-66-C0085, July 1966. A. R. Hilton, Defense Advanced Research Projects Agency (DARPA) Contract No. N00014-73-C-0367, June 1974. Physics and Chemistry of Glasses, vol. 7, 105-126 (1966). Part 1, A. R. Hilton, C .E. Jones, and M. Brau Part 2, A. R. Hilton and C. E. Jones Part 3, A. R. Hilton, C. E. Jones, R. D. Dobrott, H. M. Klein, A. M. Bryant, and T. D. George Valentina Kokorina, Glasses for Infrared Optics, CRC Press, Boca Raton, Fla., 1996. A. David Pearson, Electrochemical Society Meeting, Los Angeles, Calif., 1962. Semiconductor Effects in Amorphous Solids, W. Doremus, ed., North Holland Publishers, Amsterdam, 1969. Amorphous and Liquid Semiconductors, M. H. Cohen and G. Lucovsky, eds., North Holland Publishers, Amsterdam, 1971. R. J. Patterson, 15th National Infrared Information Symposium (IRIS) at Ft Monmouth N.J. (1966), 1967; U.S. Patent 3,360,649.

69

70

Chapter Two 23. Infrared Transmitting Materials, Materials Advisory Board, MAB-243. 24. J. Pappis and B. A. di Benedetto, Chemical Deposition of Multispectral Domes, Air Force Materials Laboratory (AFML), AFML-TR-75-27, 1975. 25. Charlie Jones and Harold Hafner, Final Technical Report, Contract No. AF 33 (615)-3963, 1968. 26. Harold C. Hafner, Final Technical Report, AFML-TR-72-54, 1972. 27. Linus Pauling, The Nature of the Chemical Bond, Cornell University Press, Ithaca, N.Y., 1948. 28. R. L. Myuller, Solid State Chemistry, Consultants Bureau, New York, 1966. 29. Thomas J. Loretz, Computer Engineering Service, Personal communication, 2004. 30. W. H. Zachariasen, J. Am. Chem. Soc. 54, 3841 (1932). 31. E. Mooser and W. B. Pearson, Acta Crystallog. 12, 1015 (1959). 32. A. R. Hilton, Phys. Chem. Glasses 9, 148 (1968). 33. Max Hansen, Constitution of Binary Alloys, McGraw-Hill, New York, 1958. 34. R. L. Myuller, L. A. Bardakov, and Z. U. Borisovaz, J. Univ. Leningrad 10, 94–101 (1962). 35. Samuel Glasstone, Text Book of Physical Chemistry, D. Van Nostrand, Princeton, N.J., 1958, p. 529. 36. W. A. Weyl and E. C. Marboe, The Constitution of Glasses: A Dynamic Interpetation, Interscience, New York, 1962. 37. T. S. Moss, Optical Properties of Semiconductors, Academic, New York, 1959. 38. Walter Gordy, J. Chem. Phys. 14, 305 (1946). 39. Gerhard Herzberg, Molecular Spectra and Molecular Structure: II, Infrared and Raman Spectra of Polyatomic Molecules, D Van Nostrand, Princeton, N.J., 1956. 40. G. R. Somayajulu, J. Chem. Phys. 28, 814 (1958). 41. G. Lucovsky, J. P. De Neufville, and F. L. Galeener, ”Study of Optic Modes of Ge30S70 Glass by Infrared and Raman Spectroscopy,” Phys Rev. 9, 1591 (1974). 42. A. Glassner, “The Thermochemical Properties of Oxides, Fluorides and Chlorides to 2500 0K,” Argonne National laboratories, ANL-5750, U.S. Government Printing Office, Washington. 43. P. Debye, Ann. Physik 46, 809 (1915). 44. A. Ray Hilton, “Titanium Chalcogenide Infrared Transmitting Glasses,” Contract No. 14-66-COOO85, Naval Office of Naval Research, 1967.

CHAPTER

3

Glass Production 3.1

Reactants After a glass composition has been selected for use, a method of preparing the glass in quantity with high quality must be developed. Of first importance is identifying a reliable source of the required elemental reactants in high-purity form. The transport properties, electrical conductance, of crystalline materials may be dominated by small concentrations of impurities in their reactants. Chalcogenide glasses have already been described as poor electronic conductors, so the metallic impurity effect on conductance is of minor consequence. However, their optical properties may be adversely affected by small concentrations of impurities. Because of the great importance of crystalline semiconductor materials, tremendous effort has been spent producing important reactants in high-purity form and developing precise methods to verify the purity of the product. Reactants used in chalcogenide glasses have benefited greatly from these efforts. Most of the elements used to produce what we might call electronic materials are by-products of primary metals production. The most important are copper, lead, zinc, silver, and aluminum. A good example is the production of pure copper at the Asarco Plant in Amarillo, Texas. Plates of 99 percent copper are electroplated on titanium plates in almost 0.5-mi-long electroplating facility. A photograph1 of the tank house is shown in Fig. 3.1. The design goal of the unit is over 400,000 tons /yr of refined copper. The resulting copper is 99.90 percent pure. A slime of waste, less than 0.1 percent of the beginning copper, falls to the bottom of the cell. In that waste are low concentrations of silver, gold, platinum, palladium, antimony, arsenic, cadmium, indium, selenium, tellurium, and thallium. These elements are chemically separated and then purified by chemical means and sold to industry. In similar processes, germanium is a by-product in the production of zinc and gallium, used to make the crystalline semiconductor gallium arsenide, which is a by-product of the production of aluminum. The costs of reactants used in chalcogenide glasses are not stable and may vary greatly. The supply of each depends upon the rate of

71

72

Chapter Three

FIGURE 3.1 The Asarco copper refining electroplating tank house at Amarillo.

production of the primary metals. When primary metal production is down and demand for the by-products exceeds the available supply, the price may rise dramatically, as for any other commodity. Another factor is purity. To be useful in electronic materials production, the purity standards are five 9s at a minimum sometimes reaching purity levels of seven 9s. There has been a tremendous improvement in purification and verification of purity techniques since the start of the semiconductor industry. The production of high-purity chalcogenide glasses has benefited as well from this development. For example, from one supplier the listed impurities in a high-purity six 9s arsenic in parts per million (ppm) are C, 0.09; Na, 0.03; and Cl, 0.08. For five 9s sulfur from a supplier, the impurities listed in parts per million were Ca < 0.2, Cu < 0.5, Fe < 0.5, Mg < 0.2, Si < 1.0, and Ag < 0.2 with the values for the common impurities C and H2O not even mentioned. Residual impurities vary among the sources of the ore used in the production of the primary metal and the production means used. Major impurities affecting optical performance of chalcogenide glasses are gas molecules of water, hydrogen sulfide, hydrogen selenide, and hydrogen telluride. Carbon, silica, and other oxides produce unwanted absorption in wavelength regions of interest. Metals such as iron produce absorption at the short wavelengths near the beginning of transmission. Sulfur glasses and selenium glasses are considered insulators or semi-insulators in their electronic conduction. The impurity iron can dope the glasses, just as if they were crystalline, forming a deep energy level in their forbidden gaps which results in increased absorption in visible or near-infrared light. Unfortunately, the analytical results furnished with the high-purity element may have been developed for other larger, more important applications than infrared glass. The impurities of consequence may

Glass Production not have been measured. The metallic impurities are often covered by routine emission spectrographic analysis. Negative impurities are more difficult and are often neglected. Arc-source mass spectroscopy will measure negative impurities such as chlorine or sulfur. Often, the only way to find out for sure if a reactant meets the need of the glass is to make a batch, perhaps a kilogram of the glass, and evaluate the outcome, usually by measuring infrared transmission through a sample 1 to 2 cm thick. The test is expensive but often necessary.

3.2

Compounding Methods The simple method of compounding a glass is illustrated in Fig. 3.2. Reactants are accurately weighed and placed in a glass tube, preferably a pure silica tube. Semiconductor-grade quartz is extremely pure and can be used without fear up to temperature of 1000°C under vacuum. A cap is provided for the end of the tube so that it can be evacuated after the reactants are in place. The loaded tube is placed in a rocking furnace and heated while pumping so that any moisture can be removed from the chamber. The temperature is raised enough to melt the chalcogen being used to remove dissolved gases. One must keep in mind sulfur melts at 119°C and boils at 445°C, selenium melts at 217°C and boils at 685°C, while tellurium melts at 450°C and boils at 990°C. After a period of time, the pump tube is sealed and removed so that the rocking can begin to form the glass into a homogeneous melt. Temperatures are kept below the boiling point of the volatile chalcogen, allowing time for the metallic elements to react which lowers the volatility of the melt. Sulfur-based glasses require special care because of sulfur’s low boiling point and because reaction with arsenic, as an example, is very exothermic. The heat generated may increase the internal pressure due to the presence of sulfur that has not reacted. Some germanium-containing glasses are reacted for hours to ensure

FIGURE 3.2

Reactants sealed in a tube placed in a rocking furnace.

73

74

Chapter Three a complete reaction of all constituents. With the quartz chamber under vacuum, reaching the boiling point of the chalcogen offsets the atmospheric pressure from outside. Each glass composition is different relative to internal pressure and heating. Care must be taken to avoid excessive internal pressure and quartz failure with the resulting reaction of the molten glass with the atmospheric oxygen. Compounding should be carried out in a closed room or hood with provisions made for exhausting any fumes in case of quartz failure. After the reaction period is over, while still rocking, the temperature is lowered to a point well above the softening point of the glass where the melt is still fluid. At this point, the glass is ready to be quenched. The furnace is placed in a near-vertical position. Prior arrangements have been made to prevent the tube of glass from falling from the furnace. Room air or blown air comes in contact with the surface of the tube. The temperature is monitored to ensure the glass reaches and stays well below Tg. After the furnace has cooled, the glass may be left to cool in room air. After cooling is complete, the quartz tube is vented to air. The quartz tube is carefully fractured and removed from the glass. The result of the operation is a 1- to 2-kg cylinder, sometimes called a boule, of the specified glass composition ready for evaluation.

3.3

Compounding with Reactant Purification In the early period of producing chalcogenide glasses at TI, the rocking furnace method described was used. In the early 1970s, the U.S. Air Force launched a great effort dedicated to developing large windows for highenergy CO2 lasers. TI became involved because in its active program large glass windows had already been cast. Reduction of absorption at 10.6 µm was a top priority. Examination of the glass using an infrared microscope identified the existence of particulate matter in the glass that turned out to be carbon from the selenium. An effort2,3 was made to remove all impurities and oxides by distillation using filters to establish the intrinsic transmission for TI 1173 and TI 20 glasses. The apparatus designed to purify the compounded glasses is shown in Fig. 3.3. H2 in

Compounding chamber

Frit

Oxides H2 out

Oxides H2 out

Se Furnace 1 Frit

FIGURE 3.3

Furnace 3 Furnace 2

Ge

Preparation of high-purity TI 1173 and TI 20 glasses.

As (or Sb)

Glass Production Germanium was considered to be the reactant of highest purity with no particulate matter, so it was loaded in the center chamber, with selenium on one side and arsenic or antimony on the other. All the materials were heated slightly, and hydrogen flowed through the chambers with the hope of reducing surface oxides. The next step was to seal the two side tubes, evacuate the chambers, and seal off the top tube. Then selenium on one side and arsenic or antimony on the other were heated and distilled through the porous quartz filter (frit) to remove particulate matter. It is worth mentioning that the distillation of antimony was extremely difficult and time-consuming. Antimony has only 10 mm of vapor pressure at 1000°C. Particulate matter (C) was not present in the resulting glass. The absorption in both glasses decreased relative to glass produced using the production method current at the time. A definite correlation for both glasses was found between increased silicon levels and absorption at 10.6 and 9.4 µm. The silica contamination, 2 to 5 ppm, probably occurred during the quartz fabrication using the hydrogen oxygen torch. The resulting oxygen concentration for both glasses, 5 ppm, was due to silica and the 8 ppm in the reactant germanium. Addition of 5 ppm Al as an oxide getter reduced absorption at 9.4, 10.6, and 13 µm. Table 3.1 lists the impurity levels found in the glasses. In the table, P refers to glass prepared using the existing production process. Most of the effort was concentrated on the TI 1173 glass which was currently used in existing systems. The reductions for TI 1173 are shown in Fig. 3.4 and compared

Glass

[Si] ppm

[0] ppm ±2

[A1] ppm

b 10.6 mm cm–1

b ~ 13 mm cm−1

1173-P

2.5

4

0.3†

0.06

0.65†

1173–92

1.4

5.5

6.1

0.012

0.19

0.0075

1173–107

2.6

5.5

6.3

0.019

0.25

0.022

1173–109

2.2

4.5

6.1

0.024

0.25

0.025

1173–122

1.1



5.7

0.013

0.22



b ~ 9.4 mm cm–1 —

0.015 †

20–P

2.2

6

0.4

0.056

0.65

20–98

4.4

5

5.3

0.053

0.34

0.045



20–102

3.3



5.6







Ge

N.D.

8

N.D.







Sb

N.D.



N.D.







Se

N.D.



N.D.









No aluminium added. N.D. = not detected.

TABLE 3.1 Impurities and Absorption in TI 1173 and TI 20 Glass Samples Used in Reactant Purification Evaluation. P Designates Standard Production

75

1.0

TI 0.012 cm–1 NRL 0.01 ± 0.005 cm–1 C.U. 0.01 – 0.007 cm–1 Production cast

β (cm–1)

0.1

0.01

0.001

2

4

6

8 10 Wavelength (µm)

12

14

16

FIGURE 3.4 TI 1173 absorption as a function of wavelength comparing standard production glass to glass made with reactant purification. 0.06

β (cm–1) @ 10.6 µm (laser calorimeter)

0.05

0.04

0.03

0.02

0.01

0

0

1

2

3 [Si] ppm

4

5

FIGURE 3.5 Absorption at 10.6 µm in TI 1173 and TI 20 as a function of silicon content.

76

6

Glass Production to results from the standard production. Also shown are results of absorption at 10.6 µm, determined by measuring the heat rise in a sample while transmitting a CO2 laser beam of known intensity. The measurement, termed laser calorimetry, was applied to the same glass by TI, the Naval Research Laboratory, and the Catholic University. Results were from 0.012 to 0.007 cm−1. A correlation between Si content and absorption at 10.6 and 9.4 µm was found for both TI 1173 and TI 20. The 10.6-µm results are shown in Fig. 3.5. The X in the figure is for the one TI 20 glass tested. Obviously, the reactant purification step would substantially improve quality and the transmission if adopted into the production of these two infrared-transmitting chalcogenide glasses.

3.4

Open Casting Methods Early preparations of glass did not involve casting. The first casting method employed at TI was termed a pour caster. A diagram of the unit is shown in Fig. 3.6. All action takes place in a sealed chamber equipped with outside controls and an observation window. The atmosphere inside is controlled flow of inert gas. The glass to be cast is placed in the crucible and moved into the melting furnace where it can be melted and stirred. After mixing and reaching of the proper temperature, the stirring is stopped, allowing any bubbles to

Stirrer

Melting furnace Crucible Mold

Window

Controlled atmosphere chamber

Mold heater

FIGURE 3.6 Diagram of the TI pour glass casting unit.

77

78

Chapter Three rise to the surface. The crucible is moved from the furnace and tilted, and the glass is poured into the mold. The glass is cooled and then annealed. Plates 5 × 5 in up to 5 × 7 in were produced. The homogeneity of glass thus produced was not good because of excess striae. A second casting method was developed in which the melted glass in the crucible was allowed to flow through a bottom hole tube into a mold directly below. This method was referred to as the bottom hole caster. Initially, the bottom hole was plugged by the first glass to melt. When casting time arrived, a heater around the bottom tube was turned on, and the glass plug melted so the glass flowed freely into the mold below. Figure 3.7 shows two photographs comparing the resulting homogeneity of glass cast using the two methods. The photographs are made from a striae scope. Collimated near-infrared light is passed through the glass plate, and the image is photographed. Light phase cancellation occurs when the light passes through striations in the glass, producing an image. The bottom hole casting was a big improvement. Optical homogeneity had become an important performance specification for highresolution infrared optical systems. The positive results from this casting change allowed an upgrade of the required MTF (modulation transfer function) image spoiling test score used to test infrared glass. The measurement required at 10 lines per millimeter an MTF score of

1173 striae standard Cast: April 1971 (old casting method)

Blank: 34173 Cast: 6/11/73 (bottom cast)

FIGURE 3.7 Striae comparison of two 5.5-in-diameter TI 1173 glass blanks cast by different methods.

Glass Production 85 percent. With the new casting method, the MTF score was raised to 94 percent, equal to that of germanium. However, for TI 1173, the bottom glass plug was found to form a large amount of crystallites grown during the glass mixing process prior to casting. When casting occurred, the crystallites flowed out and ruined a sizable portion of the cast plate. The yield of striae free large diameter lens blanks was very low. The author was asked to assume control of the TI glass production in the fall of 1974. The first change made was to implement the element purification process for compounding all the TI 1173 in the production process. It was not necessary to do the same for TI 20 glass since it was no longer in production. In working with the glass blowers, a process was devised so that double-chamber quartz tubes could be fabricated on the glass lathe. The chambers were separated by a porous quartz filter called a frit. One chamber end, the one to hold the finished glass, was left rounded and closed. The other had a wide mouth so the reactants could be easily loaded. The charge in the tube was enough to make 7 kg of glass. About 10 ppm of pure aluminum wire was added to the reactants to serve as a getter for the 5 ppm of oxides anticipated. After loading the cap was sealed, the tube evacuated, heated to melt the chalcogen, and finally sealed off for compounding. After the reactions were believed complete, the temperature was raised and the entire 7 kg distilled through the frit into the glass chamber, where it was rocked and mixed prior to quenching using blown air. The goal was high-purity glass free of particles and oxides. The second major change made was to eliminate the particles caused by the glass plug used to control the flow of glass into the mold. Again, in working with the glass blowers, a procedure was developed by which a ground glass joint was placed in the bottom of the crucible to control the flow of glass into the mold. Thus, the entire cast plate would be useful material. The ball joint was controlled by a long glass tube that reached outside the top of the chamber. After much effort, the standard production became striae-free, high–purity, 12 in × 12 in, 7-kg plates. Part of the TI success was due to vapor pressure and viscosity information supplied by Larry Swink. Figure 3.8 is a diagram of a sealed pressure measuring device produced at that time by TI. In the diagram, TI 1173 or TI 20 glass was sealed in the bottom chamber. When the glass was heated, the resultant vapor pressure produced a twist of the Bourdon tube that deflected the attached mirror. The vapor pressure was measured by the amount of nitrogen pressure applied in the top chamber to return the mirror to its original position. Vapor pressure results of the measurements are shown in Fig. 3.9 covering the elements S, Se, As, and Sb. Notice Sb is only showing 10 mm vapor pressure at 1000°C. Pressures for both TI 1173 and TI 20 are about 20 to 50 mm at 600°C near their casting temperatures.

79

80

Chapter Three N2 pressure gage & manometer system Mirror

Insulation

Heater control thermocouple Heaters Quartz bourdon pressure gage

Thermocouple #2

TI 1173 glass Thermocouple #1

FIGURE 3.8 High-temperature manometer for measuring vapor pressure above chalcogenide glass melts.

The device constructed for direct measurement of viscosity is shown in Fig. 3.10. A double quartz chamber is separated by a tube of known inside diameter and length. An amount of glass is placed in the chamber; then the chamber is evacuated, sealed, and placed in the furnace that has a hole at the center such that a HeNe laser beam can pass through the quartz flow tube. The furnace is mounted so it can rotate about the center hole. In a vertical position, the glass is melted in the bottom chamber and the temperature noted. The furnace is inverted, and the glass flows from the upper chamber through the tube down to the bottom chamber. The time required is measured by noting the time from when the laser light is blocked by the glass to

Glass Production

S

103×

As Se

TI 20 data TI 1173 data

102× Vapor pressure (torr)

TI 20 TI 1173

Sb

101×

100×

10–1× 200

FIGURE 3.9

400

600

800 1000 Temperature (°C)

1200

1400

1600

Measured vapor pressure of elements and glasses.

the time the light reappears. Viscosity then may be calculated from viscous flow fundamentals involving the diameter and length of the tube and the time required for the glass to flow through the tube. Results of the measurements for TI 1173 are presented in Fig. 3.11 and designated as experimental data. Prior extrapolated data are also shown. Later we will show how measured Tg and the softening point are used to form a viscosity versus 1/T plot for glasses. The problem in that method lies in assigning a viscosity number to Tg and the softening point. The casting temperature used in this plot is indicated by an arrow that corresponds to a viscosity value at casting of 500 to 1000 p. One disadvantage of an open casting system is that vapors are constantly escaping from the melt of the heated glass during the mixing process. As has already been pointed out, the vapors are different in

81

82

Chapter Three

Insulation

Heater control thermocouple

Equalization tube

Capillary Heaters Rotation axis

Rotation axis

Dip coil Thermocouple #2

TI 1173 melt

Thermocouple #1

FIGURE 3.10 High-temperature chalcogenide glass viscometer.

composition from the glass, which means the refractive index changes slightly. The question becomes, How slightly? Now as the glass is processed into the form of blanks, one is left with a certain amount of scrap that is valuable because it contains germanium. The desire is to clean up the scrap and reprocess it. When a boule of glass is compounded, scrap may be mixed with fresh elements as a cost-reducing means. A large producer such as TI desires to reduce cost but without degrading the system performance due to index change. The decision was made to measure the change when glass is recast. Three prisms were fabricated from standard glass production. Using the TI infrared refractometer, the index of all three was measured over the range of 2.5 to 14 µm. The values for all three were averaged and found to agree with one another over the wavelength range by ±0.0002. The process was repeated with three prisms made from glass recast once. An average value for the recast glass prisms was calculated and did not agree as well as the standard glass production ±0.0010. When the

Glass Production

103×

102× Viscosity (p)

Experimental data

101× Prior estimate (extrapolated from 107.6 p & 104.7 p data points)

100× 500

700 600 Temperature (°C)

800

FIGURE 3.11 Viscosity of TI 1173 glass measured in liquid range.

two average results were compared, the recast index increased by about +0.0040. The increase was thought to be due to loss of Se and Ge-Se vapors. The optical designer could then decide if glass could be recast once, twice, or even 3 times and used based on the index change and system design parameters such as focus. The dispersion parameters for the glass were left relatively unchanged. Figure 3.12 shows the final configuration of the casting furnace used at TI for TI 1173 glass. The chamber enclosure is round and large with a single door in front. Inside is a large quartz crucible that holds all the glass to be cast. Heaters are provided to melt and control the temperature of the glass. Provisions are made for a powered stirring device controlled from the top. A rod from the top is connected to the ball joint in the bottom of the crucible that allows glass to flow into the mold in the bottom chamber. Provisions are made for heating the

83

84

Chapter Three

FIGURE 3.12 Diagram of an open down hole glass casting unit.

mold and controlling the glass temperature after it has been cast. Using a system like this, TI, and later Raytheon, cast many tons of TI 1173 glass each year.

3.5

Purification, Compounding, Casting—One Closed Operation The changes made by the author in the TI glass casting process before leaving were not major. For one thing, the glass was in production and supplying orders for existing systems. Permission to make more drastic changes proposed by the author was refused on the valid grounds that changes could cause delays in deliveries. When Amorphous Materials (AMI) was started in May 1977, such restraints no longer existed. The fabrication of compounding chambers with porous filters on a glass lathe had already demonstrated improved purity. The drawback of the open casting system where the escape of glass vapors changed the refractive index had been investigated and the effect measured. The decision was made to combine element purification, compounding the glass, and casting in a closed sealed system into one operation. The first requirement was to recruit the most skilled master glass blower available. Glen Whaley was such

Glass Production a person who had been thoroughly trained in the Central Research Laboratories at TI. The author had worked with him many times. The most difficult job they worked on together was the building of a far infrared (95.8-µm) pure He laser. The author felt Whaley was the best person for the job and recruited him as the first employee of Amorphous Materials. He joined the company as a stockholder and a vice president. Whaley developed quartz fabrication techniques that all his former colleagues from TI told him were impossible. The task at AMI was different from the one at TI. It has been previously pointed out that AMI was not allowed to produce TI 1173 and was forced to revert to the Ge-As-Se glass, called TI 20. The glass was renamed Amtir 1. The fact that the glass contained arsenic—not antimony—made it better suited for distillation. Besides, the composition had been carefully selected so that it had no tendency to form crystallites as did the troubled TI 1173. Over a period of months, the system shown in Fig. 3.13 was developed and the glass processing steps worked out that produced high-purity striae-free 8-in-diameter plates weighing 9 kg. In the diagram, the cap covering the mouth of the compounding chamber has been sealed on and then closed after the reactant purification step. The reactants contain about 10 ppm aluminum wire to getter the oxides. The unit is placed in a two-zone furnace that moves in a horizontal plane. The temperature is raised in the compound side, and horizontal motion mixes the reactants compounding the glass. After a period of time, motion is stopped, and the compound tube side is raised in temperature to distill the glass through the filter into the round chamber to form the 8-in plate. After distillation is complete, motion is started again to mix the glass in the

Tc Tc Filter

Reactants

Compounding chamber

Casting chamber 8.00"

FIGURE 3.13 AMI closed glass compounding and casting unit.

85

86

Chapter Three

FIGURE 3.14 Striae scope photograph looking through an 8-in-diameter striae-free Amtir glass plate.

round chamber thoroughly. The glass is cooled to slightly above Tg, the furnace is opened, and air is blown on the chamber to quench the glass. After cooling, the quartz chamber is broken and the glass plate is removed. The plate undergoes a preliminary evaluation and then is placed in an oven to go through its anneal cycle. After annealing, the glass is ready for processing by sawing, core drilling, or slumping into shapes required for blanks to be fabricated into optical elements used in imaging systems. The AMI closed compounding casting glass process has produced from 1978 to 2007 over 35 tons of Amtir 1 glass in 9-kg plates. Figure 3.14 shows a striae scope photograph taken looking through an 8-indiameter striae-free plate of Amtir glass.

3.6

Summary 1. High-purity elements are required to produce low-absorption infrared chalcogenide glasses. The elements used are by-products from the production of primary metals. 2. Glass may be made in kilogram quantities in simple tubes placed in a rocking furnace. Optical quality will not be good. 3. Early TI casting units were open with melted glass poured from a crucible into a mold. Again, optical quality was not good. 4. Quality improved at TI when the glass was allowed to flow through a tube in the bottom of the crucible into a mold below.

Glass Production 5. Improvement in transmission at TI was obtained when glass was distilled through porous filters to remove particulate material and aluminum wire was added to getter oxide impurities. 6. An all-quartz closed system was developed at AMI that combined reactant purification, compounding glass, and casting all into one operation under vacuum. Optical quality was excellent.

References 1. Asarco in Texas, Eng. Mining J., September 1981. 2. A. R. Hilton, D. J. Hayes and M. D. Rechtin “Chalcogenide Glasses for High Energy Laser Applications,” Contract N00014-73-C-0367, June 1974. Sponsored by Advanced Research Projects Agency (ARPA), ARPA N0 2443. 3. A. R. Hilton, D. J. Hayes, and M. D. Rechtin, “Infrared Absorption of Some High Purity Chalcogenide Glasses,” J. Non. Cryst. Solids 17, 319 (1975).

87

This page intentionally left blank

CHAPTER

4

Characterization of Glass Properties

A

glass composition has been selected for development based on a qualitative evaluation. Now the glass has been prepared in quantity and in quality so that quantitative measurements may be made to fully evaluate the potential usefulness of the glass. Considerable effort is required. AMI started with one glass and presently produces seven. AMI thus has gone through this process a number of times. The AMI established method for preparing a glass for sale in the marketplace is a major part of the company quality control plan. Others may develop a different approach while emphasizing other properties and other methods.

4.1 Thermal Expansion, Glass Transition Temperature, and Softening Point Earlier, it was pointed out that the thermal expansion measurement defines the difference between a crystalline solid and a glass. Now it is nice if you are in possession of a sophisticated piece of equipment capable of carrying out the measurement automatically and then producing the data plotted in a nice color slide similar to some reproduced in this book. But if you are not so fortunate, you may build and use a simple device such as the AMI system shown in Fig. 4.1. A quartz glass tube inside a circulating air furnace has a quartz glass rod inside which rests on a vertical 2-in sample of the chalcogenide glass to be measured. The glass sample is in a chamber that has two sides open so that air flows freely through and around the sample. A thermocouple is placed in the chamber next to the sample, and the temperature is read from the meter on top of the furnace. Also on top, the rod is pushing against a linear in length, mildly spring loaded transducer which is monitored by an indicator. The display is set to show numerical readings in this case ±20,000. Before it is used, the transducer is calibrated in linear sensitivity to determine the numerical change per 0.001-in movement. The transducer is calibrated using a good micrometer.

89

90

Chapter Four

FIGURE 4.1

Photograph of the AMI glass thermal expansion apparatus.

The door is shut and the temperature started up in a slow, programmed manner. Numerical data are taken from the display at indicated temperatures. The sample expands linearly as a solid does, as the temperature increases to a point where it begins to expand much more rapidly. The slope changes to a greater expansion typical of a liquid. When the data are plotted, where the two slopes intercept is the glass transition temperature Tg. As the temperature continues to increase, the transducer slows its numerical increase, stops, and then decreases. That indicates the glass is being compressed by the force of the transducer. This temperature point is taken as the softening point Td (dilatometer soft point) for the glass. The data for Amtir 3 are shown plotted by hand on linear graph paper in Fig. 4.2. Such data are a good starting point. However, for more accurate data, the material should be measured again using an instrument specifically designed for this purpose as in the results shown earlier in Fig. 2.2 obtained from Tom Loretz1 of CES. Also shown earlier, CES is equipped to carry out differential thermal analysis (DTA) on powdered samples. The crystallization range may be accurately determined in this manner, also shown in Fig. 2.3. Both Tg and Td are information vital to the production of the glass composition and its use in molding, extrusion, and drawing fibers. However, the dilatometer measurement does not determine the absolute viscosity for the glass at these two points. A general value is assumed. The viscosity of a glass increases exponentially with temperature. Thus a plot of log to base 10 of viscosity versus 1 over absolute temperature will yield a straight line.

Characterization of Glass Properties 9.0

8.0

7.0

Expansion mils (0.001 in)

6.0 Tg 5.0

4.0

3.0

2.0

1.0

0 50

FIGURE 4.2

100

150 200 Temperature (°C)

250

300

AMI dilatometer measurement performed on Amtir 3 glass.

Earlier, it was mentioned that Robert Patterson2 in the TI Air Force Development Program developed the Ge-Sb-Se glass designated as TI 1173. Patterson decided to develop a device for use with chalcogenide glasses that would measure the softening point, strain point, and glass transition temperature in the absolute terms of viscosity. A diagram of this device is shown in Fig. 4.3. The device used a pointed spring-loaded (70-g) quartz rod against polished glass samples of standard size and thickness placed in a heated enclosure. Sample temperature was measured by a thermocouple placed underneath. When the penetration depth in the heated sample reached 0.05 mm, the temperature was recorded as the softening point by method A. Method B, with identical procedures, was performed except the penetration depth was increased to 0.45 mm. Softening by method B was recorded. A third ASTM softening point method sometimes used involves

91

92

Chapter Four

Dial indicator

α

Spring loaded

Quartz tube

Pointed quartz rod (90° included angle)

Sample holder (insulating) Heater Thermocouple Sample

FIGURE 4.3 Device used to standardize softening point measurements of chalcogenide glasses used by Harold Hafner at TI.

a glass fiber of specified length and dimensions heated while in a vertical position until its length begins to increase. The viscosity for this method of measuring the softening point was set at 107.6 poise (p) by Littleton.3 Three viscosity-temperature points certified by the National Bureau of Standards (NBS) for glass 712 are plotted by Patterson2 on the 1/T straight line shown in Fig. 4.4. The measured points using method A and method B performed on glass NBS 712 have been added to the plot thus calibrating these methods in absolute viscosity terms. The methods were then used to specify the strain point viscosity as 1014.6 p. The strain point is thought of as the upper use temperature for a glass. The anneal point corresponds to Tg and is specified as 1013.4 p. The softening point using the ASTM method occurs at 107.6 p. Two of the TI glasses, TI 1173 (Amtir 3) and TI 20

Characterization of Glass Properties 16

Strain point 14

Log viscosity (p)

Annealing point

12

Method A 10 Method B NBS no. 712

8 Softening point 528°C 491°C 6 1.0

1.2

439°C 1.4

386°C 352°C 1.6

1/T × 103 (K)

FIGURE 4.4 Log viscosity versus reciprocal absolute temperature for NBS glass no. 712.

(Amtir 1) were measured using method A and method B and their strain points, their anneal points Tg certified long ago. Now AMI makes both of these glasses and has dilatometer results for only Amtir 3, shown in Fig. 4.2. Combining the TI results with AMI results allows us to be able to convert the AMI data to a viscosity scale. Figure 4.5 shows a plot of several AMI glasses in a viscosity versus 1/T plot. Notice Amtir 1 and Amtir 3 have three points determined early by TI: strain point, Tg , and ASTM softening point. However, Amtir 3 has an extra point, an AMI Td softening point from a dilatometer measurement corresponding in viscosity to a value of 1011.6. The data for Amtir 6 and C1 glass were dilatometer only. Now armed with the Td viscosity number, we can make a valid viscosity versus 1/T plot for any of our glasses that can be used as a guide in using the glass. Only the two dilatometer points are needed to determine the 1/T straight-line plot for the glass. In Fig. 4.5, the temperature required to draw C1 fiber places a mark on the line corresponding to 15,850 p. Notice that the mark for Amtir 6 drawing fiber corresponds to the same viscosity. An extrapolation, not shown, for the 1/T line for Amtir 4 for fiber drawing agreed exactly with the viscosity value and temperature of C1 core glass. The bottom hole casting temperature for striae-free Amtir 3 glass determined at TI was 575°C. The intersection on the Amtir 3 line corresponds to a low viscosity value of around 10 p.

93

94

Chapter Four

Amtir 1

Amtir 3

Amtir 6

C1 core

16 15

Str. Pt.

14

Tg

13 12

Td SP.

Log viscosity (p)

11 10 9 8

ASTM SP.

7 6 5

Fiber

Fiber

4 3 2 Cast

1 0

1.0

1.5 500°C 600°C 400°C

2.0 300°C

200°C

2.5

3.0 100°C

1/T × 103 (K)

FIGURE 4.5 Log viscosity versus reciprocal absolute temperature for some AMI chalcogenide glasses.

The experimental direct measurement of the viscosity of Amtir 3 described in Chap. 3 is shown as a dashed line close to the 1/T line for Amtir 3. The viscosity data of the dashed line at 575°C indicate a value of 150 p for casting. Treatment of dilatometer data in this manner provides a useful guide when using a glass for new applications or considering the use of a new glass.

4.2 Transmission, Precise Refractive Index, and Thermal Change in Refractive Index Transmission and absorption are measures of quality and are therefore evaluated on each glass plate and recorded. In order for a glass composition to be used by designers in production of systems, much more information concerning the optical and related physical properties must be carefully measured. Complete characterization is a long and difficult task.

Characterization of Glass Properties Early infrared spectrophotometers were designed to be doublebeam with one used for reference I0 and the other for the sample I. Optical paths were equal in length and intensity so that the detected output signals were always I/I0. Some instruments used the ratio of the infrared detected electric signals while others, termed optical null instruments, had a wedge or comb placed in the reference beam to balance the two signals during the scan while recording the I/I0 ratio continuously based on the position of the wedge or comb. The transmission accuracy of commercial instruments under ideal conditions was usually considered 1 to 2 percent. For absorbing materials this may be fine. But for low-absorbing, transparent materials, it means thicker samples 2 cm or more are required for better accuracy. Unfortunately, a thick sample with a large refractive index increases the optical path in the sample beam, leading to loss in accuracy. The instruments in this generation were designed to work with organic compounds that were thin and had low refractive indexes. The appearance of Fourier transform instruments was a great step forward. In this instrument, there is only one beam and it is polychromatic. The beam transmitted through the sample is made to interfere with itself optically by using a scan mirror producing a pattern that when analyzed mathematically (Fourier transforms) reveals the variation in transmitted energy as a function of wavelength. Multiple scans are used to increase signal-to-noise results. The outcome is compared to a previously recorded, no-sample same-number-of-scans reference outcome. The results are displayed in transmission or absorption terms and printed out after desired additions to the display. Each scan takes only a few seconds. For poorly transmitting samples, increased signal-to-noise accuracy may require 50 to 100 scans and the results averaged, eliminating the influence of noise. The instruments are very versatile and useful, a real advance in the state of the art. Fourier transform infrared (FTIR) instruments used at AMI are a Perkin Elmer Paragon 1000 and a Nicolet AVATAR 320 utilized in the production area. The wavelength range generally used is 2 to 14 µm although the scan range may be changed for slightly shorter wavelengths than 2 µm or longer than 14 µm, out to 20 µm. Figure 4.6 shows a Perkin Elmer FTIR transmission scan for an Amtir 1, 8-in-diameter 9-kg plate 6 cm thick. The scan is used with the standard QC documentation preserved for each plate produced. Notice the two narrow absorptions at 4.9 and 4.5 µm due to dissolved H2Se molecules in the glass that couple to the Ge atom (4.9) and the As atom (4.5). The magnitude of absorption for the gas is low, 0.04 to 0.05 cm−1, of little consequence for lenses less than 1 cm thick. The glass tested is considered low-absorbing and has flat parallel faces so that the full expression given below for transmission should be used to calculate absorption, assuming multiple reflections. T=

I (1 − R)2 e - αx = I0 1 − R 2 e -2αx

95

96

Chapter Four

1000

1500

2000

2500

5000 4000 3500 3000

Perkin Elmer cm–4

10.0000; 57.84%T

4.0000; 59.65%T 4.4871; 47.00%T 4.9423; 43.27%T 4.000

8.0000; 59.71%T

3.0000; 58.39%T

%T

3.000

100.00

14.000

13.000

12.000

11.000

10.000

9.000

8.000

7.000

6.000

5.000

2.000

0.00

µ 08/07/03 10:44 X: 10 scans, 8.0 cm–1, apod none Amtir 16 cm thick

FIGURE 4.6 Perkin Elmer FTIR transmission scan for Amtir 1 plate 08-28.

where T = transmittance R = Fresnal reflection coefficient calculated from R = (N − 1)2/ (N + 1)2 α = absorption coefficient, cm−1 x = thickness, cm Computer programs can be written to solve for α as a function of wavelength from transmission values of plates of known thickness. For QC, computer programs are written setting minimum transmission values required for plates of known thickness as a function of wavelength. Sometimes the absorption values are set as a specification by the user. An example of how this procedure has been used is shown in Table 4.1. The specified values for Amtir 1 were set by the Army. Required transmission values for different thicknesses and wavelengths are given in the table. Conversely, a program can be written to calculate transmission as a function of thickness based on the precise infrared refractive index as a function of wavelength,

Wavelength (mm)

R

(1−R)2

R2

Tx = 0

3

0.186

0.6626

0.0347

0.6864

4

0.186

0.6626

0.0344

0.6862

5

0.185

0.6642

0.0343

0.6878

6

0.185

0.6642

0.0342

0.6877

7

T.x = 0.25"

Tx = 0.37"

Tx = 0.5"

0.75"

7.0"

0.184

0.6659

0.0340

0.6893

−1

0.184

0.6659

0.0339

0.6893

0.6800

0.6756

0.6708

0.6617

0.6529

−1

0.184

0.6659

0.0338

0.6892

0.6807

0.6763

0.6715

0.6624

0.6536

10 (.02 cm )

0.183

0.6675

0.0336

0.6907

0.6814

0.6770

0.6722

0.6631

0.6543

11

0.183

0.6675

0.0335

0.6907

0.182

0.6691

0.0332

0.6921

0.6049

0.5674

0.5296

0.4638

0.4075

0.181

0.6708

0.0328

0.6935

0.5308

0.4680

0.4085

0.3147

0.2439

8 (.02 cm ) 9 (.02 cm ) −1

12 (.2 cm−1) −1

12.8 (.4 cm ) TABLE 4.1

Calculated Transmission Requirements as a Function of Thickness for Amtir 1 to Meet Specifications

97

98

Chapter Four Calculated IR Transmission for Amtir 4 Refractive IR Index

Absorption Coefficient (cm−1)

1.00

2.7788

0.04

1.50

2.6995

2.00

2.6778

2.5 3.00

Wavelength (µm)

Thickness (cm)

Reflectivity

Transmission

2.6

0.221588

0.568757

0.005

2.6

0.211036

0.642296

0.003

2.6

0.208115

0.649923

2.6686

0.003

2.6

0.206873

0.651618

2.6637

0.002

2.6

0.20621

0.654372

4.00

2.6588

0.002

2.6

0.205547

0.655281

5.00

2.6561

0.002

2.6

0.205181

0.655783

6.00

2.6541

0.001

2.6

0.20491

0.658012

7.00

2.6524

0.001

2.6

0.204679

0.658329

8.00

2.6508

0.001

2.6

0.204462

0.658628

9.00

2.6491

0.009

2.6

0.204231

0.644245

10.00

2.6472

0.012

2.6

0.203973

0.639178

11.00

2.6452

0.014

2.6

0.203702

0.635961

12.00

2.643

0.024

2.6

0.203403

0.618777

13.00

2.6407

0.35

2.6

0.20309

0.257349

14.00

2.638

0.47

2.6

0.202723

0.187959

Fiber Results

TABLE 4.2 AMI Program to Calculate Transmission of Amtir 4 as a Function of Thickness and Wavelength

incorporating absorption coefficient results calculated from the plate scan. Table 4.2 illustrates this procedure when applied to Amtir 4. Specifications for wavelengths less than 2 µm (NIR) require the use of a different kind of an instrument. In this case, the AMI Beckman UV 5240 spectrophotometer covers the wavelength range of 0.5 to 2.5 µm. AMI uses a reflection attachment specifically designed for the instrument to evaluate antireflection coating results. The attachment mounts inside the sample area that may be closed when it is necessary to keep light out of the instrument. In double-beam operation, the instrument is an electronic null instrument not designed for highindex solid materials. Care must be exercised in taking measurements, and the results must be carefully evaluated. The fundamental absorption edge, where the glasses begin to transmit, cannot be measured using either of the FTIR instruments. The Beckman instrument must be used. As an example, a plot of the transmission edge for an 8-in-diameter Amtir 4 glass plate is shown in Fig. 4.7. Notice the plate is 2.6 cm thick.

Characterization of Glass Properties

1.0 µm 70 0.9 µm

1.25 µm

1.5 µm

1.75 µm

2.0 µm 70

0.8 µm

60

50

50

40

40

30

30

20

20

10

10 Amtir 4 absorption edge transmission (2.6 cm thickness)

0

FIGURE 4.7 edge.

0

Measured NIR transmission of an Amtir 4 plate at the absorption

For optical designers, the most important information in designing a lens is accurate, precise refractive index numbers covering the wavelength range of operation along with the sign and magnitude of the thermal change in index. The attachment to the Perkin Elmer 13 spectrophotometer used to measure the infrared refractive index at TI is shown in Fig. 2.10. The Perkin Elmer spectrophotometer serves as a monochromatic source of light. Later at TI, the attachment was changed so that the thermal change in refractive index ∆N/∆T for infrared optical materials could be measured. A diagram of the equipment is shown in Fig. 4.8. The Bridgeport Rotary Table with 5 seconds of arc accuracy turns a hollow copper chamber with a vertical flat mirror side where the glass prism is placed. The chamber may be filled from outside with coolant. The chamber is surrounded by a heat shield and an outer wall sealed to the base. Flat NaCl windows are provided to transmit the monochromatic infrared light needed to perform the minimum deviation measurement. The enclosure is evacuated, the coolant is added, and the heat shield helps maintain the reduced temperature. The temperature of the prism is measured by a thermocouple. Measurements are made at room temperature and at lower temperatures brought about by using dry ice or liquid

99

100

Chapter Four M2 Thermocouple leads

PE 301

To pump Heat shield ∗ M4 M1 Optical wedge NaCl plates 1st slit ∗

Sample dewar

30 seconds of ARC indexing table

M5 2nd slit Thermocouple detector M6 M3

FIGURE 4.8 Diagram of the equipment used at TI to measure infrared refractive index and the changes with temperature.

nitrogen as coolant. The ∆N/∆T is calculated from the results for the two temperatures. The value calculated is from room temperature down. However, in systems the materials are usually used from room temperature up. Howard Kennedy, an optical designer at TI, told the author the value listed in the literature for germanium was much too low. Those reported in the literature were also measured from room temperature down. The designer said he could demonstrate he was correct by taking a germanium lens and measuring change in focal length as the temperature increased. The author decided to test his opinion by remeasuring several materials from room temperature up, using the same equipment. All that was necessary was to pour oil in the chamber instead of liquid nitrogen. Heating elements were inserted, and the results for several materials are shown in Table 4.3. Earlier values for room temperature down are included for comparison. The data show Kennedy was right. AMI performs the minimum deviation measurement on a prism made from any infrared optical material. The method is sometimes called the Litrow mount deviation angle method because the prism is placed against a rotating mirror. The procedure followed for each

Characterization of Glass Properties l (mm)

Ge

Si

Low

High

3

330

455

5

312

428

8

307

426

10

304

12

302

Low

TI 1173

GaAs

High

Low

High

Low

High

190

58

98

161

206

184

57

92

159

216

186

55

87

157

208

427

187

56

91

148

203

424

177

56

93

153

210

162

All values in 10−6/°C; low = 25 to −197°C, high = 25 up to 100 to 150°C

TABLE 4.3

Thermal Change in Refractive Index for Ge, Si, TI 1173, and GaAs

wavelength point is demonstrated in Fig. 4.9. In this method, the monochromatic light is refracted at the surface so that it strikes the mirror at a perpendicular angle and retraces itself, forming an inverted slit image with intensity varying with the measured angle of rotation across another slit. An advantage of the method is that the light is refracted twice, in and out, while passing through the prism. The prism angle is not as large as with other methods. The method was used at TI to study the change in index with temperature for a number of materials.4 A conclusion reached in the study was that it could be possible to select a chalcogenide glass composition that would have a zero thermal change in index in the wavelength range of interest. The instrument was also used to measure TI 20 (Amtir 1) and IRTRAN IV (ZnSe). Right after AMI started into operation, an infrared refractometer similar to the one used at TI was built. A photograph of the instrument

Precise refractive index measurement procedure

D O N Mirror normal N = Angle to 3 sec

FIGURE 4.9

M Prism angle A M angle to 3 sec Apex angle A = M – N

Deviation angle O angle to 3 sec D=O–M Refractive index = sin D/sin A

The Litrow mirror procedure for measuring refractive index.

101

102

Chapter Four is shown in Fig. 4.10. It was used to verify and monitor the refractive index of Amtir 1. Later, when the Army supported the effort for AMI to become a second source of TI 1173 (Amtir 3), the instrument was used to verify that the AMI glass met the refractive index standards. The instrument was also equipped to measure ∆N/∆T. As before, a hollow copper chamber was mounted with a flat vertical aluminum mirror attached. But this time, the chamber temperature was controlled by the flow from a Neslab temperature bath. The ∆N/∆T measurements were carried out beginning as low as possible without frost or fogging and up as high as 60 to 70°C.

FIGURE 4.10 Photograph of the AMI refractometer combined with the Perkin Elmer 13 spectrophotometer.

Characterization of Glass Properties Measurements were made at AMI and published5,6 in 1990 to 1991 concerning the possible variation in refractive index during production for infrared materials available in the industry. Three prisms were made from different plates of Amtir 1 and measured. Three prisms of zinc selenide from different sources were made and measured. Six prisms were made from three sources of poly- and single-crystal germanium. The accuracy of the AMI method is demonstrated by comparing the results for the zinc selenide prism obtained from Raytheon to the previous results for the Raytheon zinc selenide published by Marilyn Dodge of NIST7 (then the National Bureau of Standards). Table 4.4 presents the results. Keep in mind that such measurements carried out at NBS took months, time that could not be spared at AMI. The AMI measurements for a glass prism covering 1 to 12 µm are carried out in 2 to 4 weeks. Again, the accuracy of the method is demonstrated in Table 4.5. AMI results for arsenic trisulfide glass agreed with the 1958 published NBS results by the average ±0.0002 measured from 3 to 11 µm. AMI believes the limit of the Litrow mount minimum deviation method when used on infrared materials is accurate and is reproducible to about ±0.0002. One of the problems with the infrared (IR) refractometer at TI and AMI was using the Bridgeport Rotary Table for measurements. The unit was heavy and difficult to rotate. All measurements were taken in the same direction of rotation. Measurements were slow and tedious. It was decided at AMI to build a computer-controlled unit that used a stepping

Wavelength (mm)

Average

NBS (M. Dodge)

Difference

3

2.4371

2.4376

–0.0005

4

2.4336

2.4332

+0.0004

5

2.4294

2.4295

–0.0001

6

2.4259

2.4258

+0.0001

7

2.4218

2.4218

0

8

2.4173

2.4173

0

9

2.4123

2.4122

+0.0001

10

2.4067

2.4064

+0.0003

11

2.4003

2.4001

+0.0003

2.3930

2.3928

+0.0002

12 Variation

± 0.0007

±0.0002

TABLE 4.4 Comparison of AMI and NBS Refractive Index Results for Raytheon Zinc Selenide: Zinc Selenide IR Refractive Index Measurements, Minimum Deviation, Average Results for Four Measurements, Corrected to 20°C, in Air Sample—Raytheon

103

104

Chapter Four

Refractive Index Values for As2S3 Glass AMI Results Two Samples 1991*

Malitson, Rodney & King, 1958†

3

2.4152

2.4155

0.0003

4

2.4116

2.4112

–0.0004

5

2.4074

2.4073

–0.0001

6

2.4034

2.4032

–0.0002

7

2.3989

2.3988

–0.0001

8

2.3937

2.3937

9

2.3883

2.3881

–0.0002

10

2.3810

2.3814

–0.0004

11

2.3736

2.3738

0.0002

Wavelength (µm)

D

0

∗Batch-to-batch variation ±0.0015. †

Values interpolated to the wavelengths of AMI.

TABLE 4.5 Comparison of AMI and NBS Refractive Index Results for As2S3 Glass

motor to replace the indexing table. The diagram of the current AMI IR refractometer is shown in Fig. 4.11. A computer-controlled stepping motor mounted in a vertical position supports the base on which the mirror is mounted. The motor requires 655,360 steps per rotation which means one step is 2 arc seconds. The monochromatic light source is the same prism monochromator originally part of the Perkin Elmer 13. It is equipped with a fused quartz prism which works well over the wavelength range of 1 to 2.5 µm and a sodium chloride prism that covers the range of 3 to 14 µm. The wavelength of the monochromatic light is changed by accurately rotating (drum turns) the mirror behind the quartz or sodium chloride prism. The monochromator is wavelengthcalibrated in drum turns versus wavelength for each prism from spectral absorption bands. Polystyrene is used for 3 to 14 µm while didymium glass and a mercury arc are used for 1 to 2.5 µm. The light source for the NIR is a high-intensity light. The MWIR and LWIR use a globar source. The globar light is chopped at the source before entering the slit of the monochromator. A signal from the chopper is furnished to the phasesensitive amplifier. The detector is a cooled HgCdTe detector for the NaCl prism and a Dexter thermopile detector for the NIR. Experience has shown that no fabricated prism is perfect. AMI results have shown that making four measurements of each prism averages out any errors. Each prism is measured facing the light right and left, up or down. The mirror is adjusted perpendicular to the horizontal plane of

Characterization of Glass Properties Digital voltmeter

Par phase sensitive amplifier

Stepping motor 655, 360 steps/360° Hg Cd Te detector

Eason computer control 1 step = 2 arc seconds

Optical 100 cycle chopper

FIGURE 4.11

AMI computer-controlled infrared refractometer.

the instrument. A HeNe laser beam is reflected from the mirror to a wall 25 ft away. A spot is marked. Alignment of the prism in each of the four orientations is accomplished by reflecting the HeNe beam from the prism face and adjusting the prism to the wall spot 25 ft away. The mirror is rotated clockwise until a switch detects a small magnet attached to its side. The computer records this step as zero. For any angle designated, the computer calculates the number of steps required and sends them to the stepping motor. A single angle input is made to the computer based on the expected angle for maximum intensity. As the mirror is rotated, a slit image of refracted monochromatic light will sweep the external slit, and the detected signal will vary with the angle. From that single initial point, the angle is increased by a specific designated increment, 0.02 degree for instance, and stops at each time so an intensity reading from the millivolt meter can be recorded for each angle. The process is repeated so 10 data points in a row are recorded. The process is adjusted and

105

106

Chapter Four repeated until the approximate maximum intensity angle is located. The computer-controlled process locates the approximate angle producing the greatest signal. A scan is then made in exact angle increments three stops on each side of the peak intensity with one near the peak. A drawing of the scan process is shown in Fig. 4.12, marking ∆θ = 0.05°

I4 I5

I3 I I6

I2 I1

I7 1 2 3 4 5 6 7 Solving for angle at maximum intensity using 7 sets of data.

Intensity – 3

5

Angle – 3

0.33 angle – 3sq

0.1089

Intensity – 2

32

Angle – 2

0.38 angle – 2sq

0.1444

Intensity – 1

109

Angle – 1

0.43 angle – 1sq

0.1849

Intensity 0

123

Angle 0

0.48 angle 0 sq

0.2304

Intensity + 1

107

Angle + 1

0.53 angle + 1sq

0.2809

Intensity + 2

38

Angle + 2

0.58 angle + 2sq

0.3364

Intensity + 3

7

Angle + 3

0.63 angle + 3sq

0.3969

Sum 1

146

= Bx

1.14

Ax

0.4382

Sum 2

152

= Bx

1.74

Ax

1.0142

3xlo-sum 1

369

= Bx

1.44

Ax

0.6912

3xlo-sum 2

223

= Bx

0.3

Ax

0.253

217

= Bx

–0.3

Ax

–0.323

440

= Bx

0

Ax

–0.07

–6265.714286

2A=

Add

A equals 210-sum 2

217

= Bx

0.03B = B= Angle = B/2A

–12,571.4

–0.3

2030.286

–1813.29 6044.286 0.480795

91

91.4808

FIGURE 4.12 A drawing representing the collection of seven sets of intensity-angle data points using equal angle increments.

Characterization of Glass Properties the intensity at each angle point. The seven sets of data points are input to the computer program to calculate the deviation angle. The increments are equal. The seven sets of data are expressed as seven quadratic equations with intensity I and angle as the variables: I = Aθ2 + Bθ + C A derivative of intensity with respect to angle is taken and equated to zero for maximum intensity: dI = 0 = 2 Aθ + B dθ

or

θ=−

B 2A

With all angle differences the same, the seven equations are added and subtracted to solve for the angle of maximum intensity. The solution is a fraction of 1°. The deviation angle as shown in the diagram is composed of the initial angle, in this case 91, added to the fraction to become 91.4808. The value is then recorded in the proper place in the computer program, so the refractive index is calculated and recorded for that specific wavelength point. An example of how the method was applied to measure the refractive index for a new AMI glass, Amtir 4, is shown in Table 4.6. The orientation is designated LD for left and down. Notice that NIR and numbers 3 to 12 are together. Such data are combined with the results from the three other orientations (LU, RD, and RU), averaged, and then fit by Bill Thompson8 to a Sellmeier equation or to a Hertzberger equation.

Mirror normal 75.72893 Material Amtir 4 Number Wavelength Ref. Angle P Normal 1 1.064 1.25 1.5 1.75 2 3 4 5 6 7 8 9 10 11 12 13 14

92.94464 92.81109 92.52313 92.29906 92.17473 92.09728 91.91464 91.86354 91.83104 91.80147 91.77626 91.74275 91.71588 91.67937 91.64149 91.59983

65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428 65.69428

Prism Normal Apex Angle NIR Date 65.69428 Apex Angle 10.03465 Amtir 4 #1 Orientation LD A + D Angle Sin A + D 4/10/2006 Sin A Index 27.25036 27.11681 26.82885 26.60478 26.48045 26.403 26.22036 26.16926 26.13676 26.10719 26.08198 26.04847 26.0216 25.98509 25.94721 25.90555

10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465 10.03465

0.45788 0.455806 0.451327 0.447834 0.445892 0.444682 0 0.441825 0.441024 0.440515 0.440052 0.439657 0.439131 0.43871 0.438137 0.437543 0.436889

0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244 0.174244

2.627811 2.615911 2.590205 2.570157 2.559016 2.55207 0 2.535671 2.531078 2.528156 2.525496 2.523229 2.520213 2.517795 2.514508 2.511097 2.507344

TABLE 4.6 AMI infrared refractive index results for Amtir 4, wavelengths 1 to 12 µm, prism orientation LD.

107

108 4.3

Chapter Four

Physical Properties Important for Optical Use 4.3.1

Hardness

Hardness is a property important in fabrication of a glass. To produce good optical surfaces, some degree of hardness is required. It has already been mentioned that some physical properties are interdependent. As shown in Chap. 2, the higher the softening point of a glass, the harder its surface. A photograph of the Leitz Miniload Hardness Tester used by AMI is shown in Fig. 4.13. The instrument has an arm with a Knoop pyramid diamond tip that is slowly pressed into the surface of the specimen under a specified load determined by added weights. The load weights may vary from 15 to 2000 g depending upon the material to be tested. For these soft materials, AMI usually uses the 50-g load. The diamond penetrates the surface, leaving a distinctive long diagonal mark

FIGURE 4.13 Photograph of the Leitz Miniload Hardness Tester instrument used by AMI to measure Knoop hardness of chalcogenide glasses.

Characterization of Glass Properties that is observed, and the millimeter length is measured using the scale in the microscope of the instrument. Several measurements may be made and averaged. The Knoop hardness (KH) is calculated from the standard formula.

KH = 14.23 × 103 ×

P L2

where P = load in g L = indention length in mm

4.3.2 Young’s Modulus, Shear Modulus, and Poisson’s Ratio These data provide information to mechanical engineers concerned with the physical strength of each component in their systems. AMI uses simple sound velocity measurements to measure Young’s Modulus E, shear modulus G, and Poisson’s ratio ν. Figure 4.14 shows a photograph of the simple device AMI used to measure sound in glass, the Panametrics 25-hp Plus Ultrasonic Thickness Gauge. Also in the photograph, right next to the gauge, is the Thermal Comparator, the instrument used by AMI to measure thermal conductivity of the glasses to be discussed in a later section. The thickness gauge instrument is equipped with a sensing head that uses transducers suited for longitudinal sound wave measurements or a transducer suitable for shear sound wave measurements. The velocity of each wave in the glass is directly measured, and along with the density ρ of the glass, Young’s

FIGURE 4.14 The Panametric 25-hp Plus Ultrasonic Thickness Gauge and the Thermal Comparator.

109

110

Chapter Four modulus E, the shear modulus G, and Poisson’s ratio ν may be calculated from the following equations:

νS = sound velocity, shear νL = sound velocity, longitudinal ν = Poisson's ratio = ρ = density G = ρνS 2

1 1  vS2  − 2 2  vL 2 − vS2 

E = (1 + ν)

Perhaps the first application of acoustical methods to chalcogenide glasses was reported from Bell Labs by Krause et al.9 when they studied sound velocity and acoustical attenuation in TI 20 (Amtir 1) glass. The application of this technique to chalcogenide glasses made at TI and at AMI was the result of efforts by Don Hayes while at TI.10 Hayes applied this method to characterize some of the TI sulfur and selenium chalcogenide glasses shown in Table 4.7. Later, he published a more complete treatment11 for Ge-Sb-S glasses. He was the one who selected the equipment used by AMI.

4.3.3

Rupture Modulus

The rupture modulus is an experimentally determined value related to the ability of the glass to resist fracture under the stress of force. E (106 psi)

G (106 psi)

n

Se

1.43

0.545

0.315

Ge17.5Sb7.5Se75

2.35

0.92

0.279

Ge21Sb9Se70

2.56

1.00

0.278

Ge28Sb12Se60 (1173)

3.16

1.26

0.265

As2Se3

2.65

1.03

0.289

#20

3.17

1.26

0.266

#20 (Bell Labs12)

3.29

1.31

0.261

Ge15S70As15

2.01

0.776

0.295

Ge36S60As4

3.05

1.22

0.250

Ge37S60As3

3.37

1.38

0.244

Ge40S50As10

4.26

1.70

0.251

Ge35S25As40

6.08

2.39

0.271

Ge30Se30S30As10

2.72

1.02

0.274

Ge20Se25Te30As25

3.00

1.18

0.270

TABLE 4.7 Elastic Moduli of Sulfur- and Selenium-Based Glasses

Characterization of Glass Properties T P

P

where P = T /2 (T = total applied load) L = distance between suspension points b = width of test specimen Glass h = thickness of test specimen

L MR = 3 PL 2 bh 2

FIGURE 4.15

Diagram depicting the rupture modulus apparatus.

The procedure takes time and money in that a lot of good material must be polished first and then destroyed. AMI uses four-point loading on polished bars. The bars must be thick enough to provide good data and long enough to stretch across the apparatus not close to the ends. The bars must be polished carefully with edges beveled and polished. A minimum of 10 bars should be broken. A diagram of the apparatus used is shown in Fig. 4.15. The formula used in the calculation is also given. The preparation for the measurement takes much longer than the actual breaking of the bars. Results obtained for Amtir 4 are given in Table 4.8. Note there are only nine data points. That is

Breaking Force (lb)

Rupture Modulus (psi)

Bar No.

Width (in)

Thickness (in)

1

0.723

0.434

60

2644

2

0.720

0.416

58.5

2817

3

0.725

0.432

57.5

2550

4

0.956

0.414

57.5

2106

5

0.892

0.431

71.5

2589

6

0.894

0.432

56.5

2032

7

0.955

0.433

57.5

1927

8

0.888

0.413

58.5

2317

9

0.890

0.412

56.5

2244

Average = 2358 ± 259 TABLE 4.8

Amtir 4 Rupture Modulus

111

112

Chapter Four so because a bar or two were rejected when examined close to the beginning of the process. All chalcogenide glasses measured at AMI have had a rupture modulus greater than 2000 psi but less than 3000 psi. The highest has been Amtir 1, as you would expect, at about 2700 psi. The value was confirmed twice in a Navy study. A different approach was taken at TI; plates were broken instead of glass bars. A set of metal concentric rings was used in place of bars in determining the rupture modulus. Also, the smaller-diameter upper ring was connected using a swivel joint to ensure force was applied evenly to the surface of the plate. Figure 4.16 shows photographs of a two 5.5-in-diameter plates of TI 1173 after being broken. One was 0.5 in thick and the other 0.25 in. The fracture patterns are clear in the photographs.

4.3.4 Thermal Conductivity The absolute measurement of thermal conductivity for a solid is no easy task. Such a statement applies strongly for materials with low values. All glasses are considered poor thermal conductors because they are disordered solids. Chalcogenide glasses are even worse than oxide glasses. For many years, AMI has used the Thermal Comparator instrument developed by the Thermophysical Properties Research Center at Purdue University. A photograph of the instrument is seen in Fig. 4.14. The controls and microvoltmeter are the main unit while the thermal probe unit is on the right side. Also shown in the photograph is the acoustical thickness gauge unit to the left. The thermal probe has a thermal reservoir heated to 10 to 30°C above room temperature. The voltmeter is zeroed. A sample is placed over the hole in the sensing unit, and the lever is pushed down, which mechanically brings the probe in contact with the bottom of the sample and the Constantan tube leading from the heat reservoir. Heat begins to transfer from the reservoir to the sample. Chromel thermocouples on top of

Picture taken immediately after fracture, 5.5 in diameter, 0.5 in thick

FIGURE 4.16

With top plate removed, 5.5 in diameter, 0.25 in thick

Rupture modulus measurement of TI 1173 glass plates.

Characterization of Glass Properties the heat reservoir and ones in the tip of the sensor tube begin to develop a voltage difference. When the voltage becomes steady, the reading is taken as a data point. The instrument comes equipped with six samples of known thermal conductivity values certified by NBS. The readings are taken using the standards and plotted on linear 4 log paper as a calibration curve shown in Fig. 4.17. The unknown sample is measured in the same way, and its place on the curve establishes its thermal conductivity value.

4.3.5

Electrical Resistance

Chalcogenide glasses are covalently bonded and show none of the ionic conductance that you may find in oxide glasses. Those based on sulfur are generally insulators, some transmitting visible light which

0 10 8 6 5 4 3

Copper

Thermal conductivity [W/(cm·°C)]

2

BeCu 25

10 8 6 5 4 3

Armco iron

2 316 Stainless steel 10–1 8 6 5 4 3

A 110 AT

2

Pyroceram Fused quartz Pyrex (corning 7740)

10–2 8 6 5 4 3 2

Ebonite

10–3 40

80

120

160

200

240

Thermal comparator reading (µV)

FIGURE 4.17

Calibration curve for Thermal Comparator.

280

320

113

114

Chapter Four demonstrates an electronic bandgap >1 eV. The bandgap indicates an average bond energy for the solid. Most all selenium-based glasses are semiconductors with bandgaps of 1 eV or less. Just like crystalline semiconductors, they are electronic conductors with electrons and holes but with extremely low carrier mobility. Their resistance is classified as semi-insulating. When they are heated, free carrier absorption in the infrared, as in crystalline semiconductors, if it occurs at all, is too weak to be observed. Glasses containing or based on tellurium may show much higher conductance than selenium-based glasses. Greater metallic character is due to the presence of tellurium. Radiation damages the lattice of crystalline semiconductor materials, knocking atoms out of place and creating defects. For visible light-transmitting solids, color centers may result as impurity metallic elements become activated. For crystalline semiconductors, the conductivity may change due to defects decreasing the carrier mobility. Chalcogenide glasses are already disordered solids. A large amount of radiation would be required to make the solid much more disordered than it is already. Also, most do not transmit visible light, so color centers would not be observed. Carrier mobility is already very low.

4.4

Resistance to Chemical Attack Glasses generally are less chemically active than crystal materials. Chalcogenide glasses are chemically inert to most common substances with the exception of strong alkaline solutions. Chalcogenide glasses are inert to most common organic liquids such as acetone and alcohol. Exposure for weeks to nonoxidizing acids such as hydrochloric, hydrofluoric, and sulfuric acids at 5N concentration has no effect. Amtir 1 was tested by the Navy in San Diego Bay with flowing seawater with no effect after 3 months. Still, it is always best to test. Glasses based on different elements may show different chemical reactivity. For example, Si-Se glasses are very reactive with water, evolving H2Se gas, while Ge-Se glasses are stable to water. One test method to follow is to cut and polish a number of small disks, with about 1 in diameter and 0.2 in thick. Weigh each one, identify them, and measure the transmission of each. Expose each one to a chemical to be tested, varying the conditions such as time and temperature. At the conclusion, weigh and run the transmission. Comparison before and after will indicate the resistance to each chemical tested.

4.5

Final Production Procedure Once the chalcogenide glass composition has been selected, the related physical properties and optical properties are measured accurately, and the decision is made to produce the glass, the process begins to produce the glass in quantity and verified quality. In the AMI process, the reactants are weighed out accurately to 0.1 g using an electronic

Characterization of Glass Properties balance. Sealed in the quartz containers, the finished composition is guaranteed. Each step of the compounding casting process is controlled by a computer program. A unique program in temperature and time is developed and stored for each glass composition produced. Generally, the process, start to finish, takes 48 h. After the process ends, the quartz container is broken and the plate is removed. Preliminary evaluation consists of an FTIR scan and examination for particles, bubbles, and fractures using an infrared microscope. If the plate is judged good, the anneal cycle is next. The anneal furnace is large with a good circulation of air. The plate is heated up to an anneal point near the Tg and then held at this temperature for several hours. Cooldown is slow, perhaps 1° per hour for the first 20° then faster to room temperature. Anneal cycles vary for each glass, lasting from 3 to 5 days. The thermal history of the glass has an effect on the refractive index in the last three to four decimals. The process should be fixed before the final refractive measurements are made and the numbers distributed. Once established, the anneal process should not be changed. After anneal, the plate is ground flat and parallel and is polished; transmission is measured and checked against standards and examined again for particles. Results are recorded on the QC sheet for the plate. Each plate has a number assigned in the beginning, and the sheet is kept on file for future reference. The plate is then examined for the presence of striae using the AMI “striae scope.” a diagram of which is shown in Fig. 4.18.

GaAs light emitter Mirror

Mirror

8" Aperture

8" Dia Amtir plate

Micrometer viewer model 7290

Monitor

FIGURE 4.18

Diagram of the AMI striae scope.

115

116

Chapter Four A 1-µm-wavelength gallium arsenide light emitter is placed off-axis at the focal point of a 10-in telescope mirror. Focal lengths of both mirrors are 48 in. The mirrors are aligned facing each other. A NIR camera is placed off-axis in the opposite direction at the second mirror’s focal point. The result is a beam of parallel light passing through an aperture and focused on the camera with the image shown on a TV display. The polished plane parallel plate is placed against the aperture. Any regions in the plate where the refractive index is varying will show up in the image darker than the rest of the plate due to phase cancellation in the parallel wavefront. Also, cracks or large bubbles or particles will be visible. The process is carried out in a darkened room. The operator may mark on the plate with a grease pencil any areas that are not homogeneous and should be avoided. When the plate is sawed or coredrilled for blanks, these marks are used to guide the operator. In the 1980s, AMI used an image spoiling test as ordered by the Army to verify the optical quality of each lens blank produced. The process was used to measure the modulation transfer function (MTF) in the 8- to 12-µm range of a high-performance FLIR test module and then to remeasure the module with the blank in the optical path. The decrease of the MTF score was used to pass or reject the blank. The process was time-consuming and expensive. Some blanks failed because of the quality of the polish, not striations. After a period of time, AMI was able to demonstrate to the Army that the AMI striae scope method was better than the image spoiling test and the MTF test should be discontinued. The cost of the lens blanks was reduced by 20 percent. To emphasize the usefulness of this technique, two striae scope photographs are shown in Fig. 4.19. The top photograph is taken of an early Amtir 5 plate, number 10. One can clearly see the variation in index in the plate, striae. The second photograph is plate number 19, showing a striae-free plate due to the success of the process adjustments. Use of the striae scope is somewhat subjective and yields no absolute number useful for comparing the homogeneity of different infrared optical materials. The classical method is to use an interferometer to measure the optical wavefront distortion (OPD) when light is transmitted through a plate of the material. Rosberry12 reported perhaps the first homogeneity results for infrared optical materials. The materials tested were silicon, zinc sulfide, magnesium fluoride, and calcium fluoride. Although other companies continued using MTF image spoiling tests, AMI decided it would be a good idea to have AMI materials evaluated by an interferometer test. A plate of Amtir 1 was sent to R. M. Ranat of Pilkington. A MTF image spoiling test as well as the interferometer showed that Amtir 1 was about 2 times as homogeneous as single-crystal, annealed germanium. Bill Spurlock of Exotic Materials found a similar value for Amtir 1. Later Spurlock measured Amtir 3 and Sullivan of Exotic Materials measured gallium arsenide for AMI. The results

Characterization of Glass Properties

FIGURE 4.19

Striae scope photographs of Amtir 5, 8-in plates.

are presented in Table 4.9 for AMI materials along with other widely used infrared materials for comparison. Also included are approximate values of ∆N/∆T for the materials. The homogeneity numbers are given as ∆N/N in units of 10−6. Amtir 1 has the lowest value except for ZnSe which was not a three-dimensional test. One explanation for the low value for Amtir 1 is that all three constituent atoms, Ge-As-Se, are on the same row of the periodic table and next to one another. Thus, since the refractive index primarily reflects atomic mass and these three atoms are almost the same, compositional variation is not a factor for this glass. To carry this argument one step further, Amtir 5 is an As-Se glass. Therefore, Amtir 5 should be more homogeneous than Amtir 1. Using a Wyko Interferometer, AMI evaluates the homogeneity of every Amtir 5 plate for use in the Lockheed Martin JSF Fighter. Averaging the results for five plates, the Wyko results showed a value for ∆N/N for Amtir 5 of 6.1, lower than the 8 value for Amtir 1.

117

118

Chapter Four

IR Refractive Index

Index Homogeneity DN/N × 10–6

Thermal Change Index DN/DT ¥ 10–5/°C

Germanium (single crystal)

4.0

17∗

43

Gallium arsenide (poly)

3.3

20†

20

Zinc selenide (poly/ cvd)

2.4

3‡

6

Ge33As12Se55 (Amtir 1)

2.5



7

Ge2Sb12Se60 Amtir 3

2.6

19¶

10

As40S60 (As2S3 glass)

2.4

N/A

±0.9

Material

∗UK Rarde Results, 1984; Spurlock Exotic Materials, 1990. †

Sullivan Exotic Materials, 1991. Raytheon number for plane perpendicular to the growth axis. Does not include gradient in growth direction. § Ranat Pilkington, 1991; Spurlock Exotic Materials, 1990. ¶ Spurlock Exotic Materials, 1991. ‡

TABLE 4.9

Optical Homogeneity of Some Infrared Optical Materials

References 1. Thomas Loretz Computer Engineering Services, private communication. 2. R. J. Patterson, “Research on Infrared Optical Materials,” TI Report No. AFALTR-66, Texas Instruments, November 1966. 3. J. T. Littleton, J. Amer. Ceramic Soc. 10, 259 (1927). 4. A. R. Hilton and C. E. Jones, “The Thermal Change in the Nondispersive Infrared Refractive Index of Optical Materials,” J. Appl. Phys. 6, 1513 (1967). 5. A. R. Hilton, “Precise Refractive Index Measurements of Infrared Materials,” SPIE 1307, 516 (1990). 6. A. R. Hilton, “Infrared Refractive Index Measurement Results for Single Crystal and Polycrystal Germanium,” SPIE 1498, 128 (1991). 7. Albert Feldman, Deane Horwitz, Roy M. Waxler, and Marilyn J. Dodge, NBS Technical Note 993, Optical Materials Characterization (1978). 8. Bill Thompson, Optical Services Co., Lucas, Texas. AMI Optical Science Consultant. 9. J. T. Krause, C. R. Kurkjian, D. A. Pinnow, and E. A. Sigety, Appl. Lett. 17, 367 (1970). 10. A. R. Hilton, D. J. Hayes, and M. D. Rechtin “Chalcogenide Glasses for High Energy Applications,” Contract No. NOOO14-73-0367,DARPA Order No. 2443 (1974). 11. D. J. Hayes et al., Proceedings of the Ultrasonics Symposium, 502 (1974). 12. F. W. Rosberry, “The Measurement of Homogeneity of Optical Materials in the Visible and Near Infrared,” Appl. Opt. 5, 961 (1966).

CHAPTER

5

Conventional Lens Fabrication and Spherical Surfaces

A

glass composition has been selected for development. The optical and related physical properties have been determined, and the glass has been selected for fabrication into lenses. A plate of the glass has been compounded, cast, and annealed. The plate has been ground flat and parallel using a Blanchard Mill and polished for final inspection. A serial number is assigned and inscribed on the outside edge of the plate and transferred to the quality control sheet along with all the evaluation data. The plate is turned over to production for lens blank fabrication.

5.1

Lens Blank Preparation In this particular instance, the plate is a 9-kg plate of Amtir 1, with 8 in diameter and 2 in thickness. The plate will be blocked in an oven on a silicate glass plate using blocking wax. After cooling cylinders of glass, the correct diameter for the lens will be diamond cored drilled out of the plate as shown in Fig. 5.1. The plate is shown along with a glass cylinder. The cylinders have a piece of ceramic epoxied the length of the core to serve as the last material to be sawed through, which prevents chipping of the edge of the lens blank. In Fig. 5.2, we see glass cylinders glued together with epoxy end to end to increase the number of blanks sawed at one time. For greater efficiency, other end-to-end cylinders may be added side to side to increase the number of blanks produced at one time. Figure 5.2 is a photograph of blanks being sawed. Notice the white ceramic glued to the bottom of the cylinder. The controls on the saw are set so that the thickness of each blank is the same. The hole in the ID saw is large, with a 3.5-in diameter which allows use on larger blanks or more ganged together. After the sawing is complete, the sawn parts are placed in a container and soaked in acetone to remove the ceramic and epoxy. Most of the lenses

119

120

Chapter Five

FIGURE 5.1 Core drilling a glass cylinder from a plate.

produced at AMI are small and simple, planoconvex, with 1 in diameter. Production rates as high as 2000 per month have been maintained over long periods. The lenses produced are inexpensive, used mostly for thermal sensing. Total production by AMI since 1984 is well over 250,000. The lenses can be used to form images but are not considered good quality.

FIGURE 5.2 Sawing individual lens blanks with the ID saw from end-to-end glass cores.

Conventional Lens Fabrication and Spherical Surfaces

5.2

Generation of Spherical Surfaces Until recent years, almost all lens optical surfaces were spherical. The generation of a spherical surface with the correct radius of curvature was an important step in the production of any lens. Figure 5.3 shows a diagram depicting the process of generating a spherical surface. The blank of glass to be generated is mounted on the lower vertical spindle. The generating tool is mounted on a spindle at an oblique angle to the vertical spindle. Both spindles are spinning. The generating tool is hollow with both its outside and inside edges covered with diamonds. In the diagram, a convex surface is being generated. The inside-diameter edge W is being used. The outside-diameter edge is used for concave surfaces, and W is slightly larger than the inside one. Both of these edge diameters must be greater than one-half the diameter of the part being generated. One may think in terms of the points of edge contact forming a cord on a circle of radius of curvature R of the lens. The angle θ between the axis of rotation for the tool and that of the part being generated can be calculated by

θ = sin−1 (W/2R) (180/π) where W is the inside diameter in this case and R the desired convex radius of curvature. In practice, the operators are furnished tables covering the settings for standard tools and desired curvatures by the company that manufactures the generator. This method is practical and has been used for many years.

FIGURE 5.3

Diagram depicting the generation of a spherical surface.

121

122 5.3

Chapter Five

Polishing AMI has 22 spindles in operation, a small number in comparison to an optics fabrication shop. The spindles are used mostly for polishing. The polishing slurry used is mostly based on aluminum oxide with some silica and zirconium oxide. The slurry is pumped and circulated over the parts during polishing. Single-spindle operation requires a lot of attention by the technician and thus is not very efficient. AMI developed a multiblocking technique to increase production of the small 1-in- diameter planoconvex sensor lenses. First, one side of each blank is polished and then covered with a protective coating of paint. Next, they are mounted in their respective tool using a soft blocking wax. Figure 5.4 shows two spindles with multiple lens blanks blocked in the recesses on the spherical convex surface of the tool. The smaller tool is for lenses with shorter focal lengths and thus a smaller radius of curvature. Fewer lenses may be made at one time than with the other tool used for longer focal length lenses. Here the radius of curvature is larger, requiring a larger convex sphere. These two tools are placed on the bottom vertical spindles. Not shown is the top concave tools with the exact radius of curvature for their respective lenses. The bottom spindles are rotated and the top spindles moved back and forth while the bottom tools are spinning. Of course a polishing solution is sprayed on all the parts at the same time. After the polishing is finished, the lenses are unblocked in an oven. After cooling, they are placed in an ultrasonic cleaner with a solution that removes all the wax and paint. Each lens is then checked for curvature and center thickness.

FIGURE 5.4

Multiblocked Amtir 1 planoconvex 1-in lenses.

Conventional Lens Fabrication and Spherical Surfaces

5.4 Testing Now that the spherical surface has been generated and polished, how to check it? Again, a simple and practical way is to use a “bell,” as illustrated in Fig. 5.5. A linear dial indicator is placed inside a bell that has an opening with a known diameter. The bell with indicator is first placed on a flat to zero the indicator. When it is placed on a part, a sag reading is made. The absolute value may be used to evaluate the radius of curvature, or a reading from a standard may be used for comparison. Concave surfaces may be evaluated in a similar manner. The method is fast and effective for many small lenses. Many lens fabrication operations use test plates fabricated from optical glass for a specific radius of curvature needed for many parts. The curvature is tested by placing the part in light contact with the test plate under a light source with a specific light emission. Interference fringes results are counted in number and shape to evaluate the finished surface. Others have an instrument capable of measuring the

0.0000

Bell

Flat Standard

FIGURE 5.5

Part

Mechanical spherometer for measuring radius of curvature.

123

124

Chapter Five modulation transfer function (MTF) of the lens using collimated monochromatic light. The focal length of the lens is confirmed, and the quality of imaging in terms of line pairs per millimeter is resolved on and off axis and is calculated and tabulated. In the early years of AMI, the Night Vision Laboratory at Ft. Belvoir (NVL) required AMI to run an image spoiling test on each Amtir 1 blank before shipping. NVL provided the funds for AMI to purchase from Lou Fantozzi of Diversified Optics, a computer-controlled MTF instrument. In the test, the instrument measured the MTF of a high-performance three-element infrared lens designed by Fantozzi and fabricated at Diversified Optics. A carefully polished Amtir 1 blank was then placed in the optical path, and the MTF of the lens was remeasured. The relative MTF score at 10 line pairs per millimeter had to be 94 percent or better for the blank to pass. AMI used the instrument for this test several years until the test was deemed costly and unnecessary because the pass rate was 99 percent. Eventually the instrument was no longer functional and was not replaced by AMI. In 2000, AMI began molding chalcogenide glass lenses in a joint program with Lockheed Martin in Orlando, Florida. The molds used were of very high quality, and as the work progressed, it became important to have a method to verify the accuracy of the molding process. AMI purchased a ZYGO interferometer instrument, shown in Fig. 5.6 mounted on a stabilized optical table. Not visible in the photograph on the right-hand side of the table is a WYKO interferometer used to evaluate the optical homogeneity of each Amtir 5 plate produced by AMI to be used in the Lockheed Martin JSF Fighter. Figure 5.7 shows a ZYGO evaluation sheet

FIGURE 5.6 Photo of the AMI ZYGO interferometer.

125

FIGURE 5.7 ZYGO evaluation sheet for a molded Amtir 5 lens.

126

Chapter Five for a small Amtir 5 molded part. The results on the sheet show a PV of 0.427 wave, an rms of 0.067 wave, and a power of –0.271 wave. The Instrument uses a He-Ne laser emitting at 0.6328 µm. Also not shown in Fig. 5.7 is a mechanical device used to measure the wedge of the molded lens. Each molded lens is evaluated in this manner, and the results are used in improving the molding process. AMI now molds four of its glasses.

5.5 Antireflection Coatings Previously it was pointed out that glass surfaces are generally more inert than crystalline surfaces. Glasses are more resistant to chemical attack. In applying antireflection coatings, inertness becomes a handicap. Coating designers then have to revert to what they generally call glue layers. Each develops her or his own favorite for different materials. The purpose is to apply a very thin layer, too thin to be optically significant, to provide a surface to which the first coating layer will adhere. High melting oxides such as aluminum oxide or magnesium oxide are examples that are favored by some. AMI for many years was not involved in coatings. The situation changed when in 1997 AMI began a SBIR Phase II program with the Navy to fabricate an infrared imaging bundle from As2S3 glass fibers 10 m in length. The program goal was an overall transmission of 50 percent in the 3- to 5-µm band. With an optical path of 10 m to contend with, it seemed obvious that an antireflection coating to reduce Fresnel reflection losses would be required to meet the transmission goals. Ed Carr, a former colleague of the author at TI, was recruited. Carr, although retired, had almost 40 years’ experience at TI and other companies in the area designing and producing coatings for infrared optics. He joined the program. From a local company, a rebuilt Temescal unit was purchased with one special modification. Two flanges were welded on top of the chamber. The ends of the flanges were fitted with O-ring seals such that fiber ends could be inserted through the seals to be coated without contaminating the chamber. All coatings designed by Carr used mixed fluorides in place of the radioactive thorium fluoride used by many in the industry. The results of the three-year effort to produce the 10-m bundle have been reported in the literature.1 It turns out that the antireflection coatings were not used on the bundle ends because they caused crosstalk problems between the fibers with a loss in contrast of the image. After the SBIR program ended in 1999, efforts turned to providing coatings for all the glasses produced by AMI with special interest in the low-temperature glasses Amtir 4 and 5 developed for use in molding. It became important to be able to coat the lenses after they were molded. New coating designs were developed. A new larger, computercontrolled, more up-to-date coating chamber was purchased. The Cryo pump was backed by a turbo pump so that ion beam assisted deposition could be used to improve coating quality. After deposition, the coatings must be evaluated relative to reflectivity and tested for

Conventional Lens Fabrication and Spherical Surfaces resistance to humidity, adherence, and resistance to abrasion. All AMI films are tested according to MIL-PRF 13830B, Appendix C 3 8.2, the 24-h humidity test, 3841 the severe abrasion test, 3842 the moderate abrasion test, and 385 the adhesion test. The humidity test is carried out in a commercially available environmental chamber. Adhesion is a tape pull test using a designated tape. Both abrasion tests are surface rubs under exact conditions observing damage. During the coating operation, extra pieces are included to serve as witness samples. Quality tests are performed on these. If the witness samples pass, the coated parts may be approved for delivery. The first step is to verify the reflection from the surface conforms to the design. The Beckman Vis-NIR spectrophotometer has a special reflectance attachment designed for the instrument. Some coatings must be evaluated in the NIR even close to the visible light. Most are confined to the infrared well within the range of the Perkin Elmer FTIR. Figure 5.8 shows the reflection attachment for the FTIR. Notice the sample used is a crystal of high-purity silicon. The reflectivity of silicon is flat at 30 percent throughout the 2- to 14-µm range and is used as a reference. An aluminum, gold, or silver mirror would show much higher reflectivity than silicon, but is not stable with time and offers no sensitivity advantage. When the reference or background scan is silicon, a gain in sensitivity occurs. Since an indicated 100 percent reflectivity is only 30 percent, a horizontal 10 percent line on the scan is in reality only 3 percent reflectivity. Figure 5.9 shows an actual FTIR scan of a 3- to 5-µm coating on Amtir 4. The 10 percent line represents only 3 percent reflectivity. The point at 5 µm reading 3 percent then is only 1 percent actual reflectivity. Figure 5.10 shows a FTIR reflection scan for an 8- to 12-µm coating

FIGURE 5.8

Reflection attachment for Perkin Elmer FTIR.

127

1000

1500

2000

2500

5000 4000 3500 3000

PERKIN ELMER cm–4

Hcursor

100.00 %R

3.5000; 1.13%T 4.0000; 1.16%T

5.0000; 3.05%T

4.000

5.000

10.00

03/12/10 08:34 X: 10 scans, 4.0 cm–1 03–83 coated Amtir 5 wedge vs SI backg.

14.000

13.000

12.000

11.000

10.000

9.000

8.000

7.000

6.000

3.000

2.000

0.00

µ

FIGURE 5.9 FTIR reflection QC scan for 3- to 5-µm coating on Amtir 4.

2000 5.000

1000

2500 4.000

1500

5000 4000 3500 3000 2.000

PERKIN ELMER cm–4

8.0000; 2.03%T

9.0009; 1.32%T

10.0000; 1.20%T

10.9999; 1.20%T

12.0005; 2.23%T

9.000

10.000

11.000

12.000

10.00

8.000

Hcursor

100.00 %R

03/07/03 06:36 X: 10 scans, 4.0 cm–1 03–58 coated Amtir 4 wedge vs SI backg.

FIGURE 5.10

128

µ

FTIR reflection QC scan for 8- to 12-µm coating on Amtir 4.

14.000

13.000

7.000

6.000

3.000

0.00

Conventional Lens Fabrication and Spherical Surfaces

1000 10.0000; 98.16%T

10.9999; 97.18%T

10.000

11.000

12.0005; 94.56%T

9.0009; 98.23%T 9.000

cm–4

8.0000; 97.74%T

2000 5.000

Hcursor

100.00 %T

8.000

2500 4.000

1500

5000 4000 3500 3000 2.000

PERKIN ELMER

10.00

03/07/03 06:42 Z: 10 scans, 4.0 cm–1 03–57 & 58 coated Amtir 4 blank

FIGURE 5.11

14.000

13.000

12.000

7.000

6.000

3.000

0.00

µ

FTIR reflection QC scan for 8- to 12-µm coating on Amtir 4.

again on Amtir 4. Note all the measured parts were less than 1 percent actual reflectivity. Figure 5.11 shows a FTIR transmission scan again for an Amtir 4 sample. In this case the reference is a standard background. The sample is coated on both sides with the standard coating. The average transmission across the band is 97.18 percent. One disadvantage for coating the low-softening-point glasses developed for molding is that they must be coated at low temperatures. To produce a good hard coating, one needs heat as the materials are deposited. Only one AMI glass passes the severe abrasion test— Amtir 1. Amtir 1 has the highest softening point and can be coated at a higher temperature than the others. Coatings on other AMI glasses pass the mild abrasion test. One other factor to keep in mind is that chalcogenide glasses have relatively large thermal expansion coefficients. One should keep this fact in mind when selecting the materials to be deposited as layers in the coating design.

Reference 1. Ray Hilton, Sr., Ray Hilton, Jr., James McCord, Glen Whaley, Thomas J. Loretz, and Paul Modlin, “Fabrication of a 10 Meter Length IR Imaging Bundle from Arsenic Trisulfide Glass Fibers,” SPIE 3596, 64 (1999).

129

This page intentionally left blank

CHAPTER

6

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos

I

n Chap. 5 the fabrication methods producing spherical optical surfaces in use for many years were discussed. The methods were applied in the fabrication of visible as well as infrared lenses. Two technical advances brought about a dramatic change. The first was the direct application of computer control of machine tools that led to diamond point turning. The second was the development of inexpensive uncooled infrared detector arrays,1 the most expensive part of the cost of infrared cameras. Now the most expensive cost of the cameras became the optics. Attention turned to lowering the optics cost.

6.1

Optical Designs In Chap. 5 an optical element designed by Louis Fantozzi of Diversified Optics was described as a test element in an image spoiling test for Amtir 1 blanks. The lens had three elements, two germanium and one Amtir 1. Each lens had all spherical surfaces. When tested in the wavelength range of operation, 8 to 12 µm, the design produced an MTF score of 70 percent at 10 line pairs per millimeter and 50 percent at 20 line pairs per millimeter. The performance was more than adequate for the then Army common module FLIR. Lens designs for high performance with all spherical surfaces required the use of three or more elements and two or more different optical materials. It is true that aspheric designs could be made to improve performance and produced, but with great difficulty using the old spherical methods. The goal to lower cost became the search for new designs using only two lens elements and still maintaining the required performance.

131

132

Chapter Six Better still would be a Petzval design that used only one material in the two-element design. Aspheric surfaces and the addition of diffractive surfaces would improve color correction. Designers use computer software such as ZEMAX that provides the ability to iterate their designs to produce maximum performance. Positions of each lens may be changed one at a time while the thickness of each lens and the radius of curvature, all may be changed while witnessing the change in performance. Before beginning a lens design for a camera, the designer needs to know the area of the detector array and the number of elements in order to calculate the area of each detector element, the pixel size. The finished lens design must have enough performance to resolve each detector element. The greater the number of detector elements, the greater the optical performance required. Specified field of view and performance off-axis requirements must be met as well. The final product of a lens design is a lens drawing used by the fabricator to produce this specific part. Besides a drawing of the lens element, usually drawn to some scale, the material to be used will be specified along with a callout for the drawing, if available, which specifies the material requirements. Inner and outer diameters may be specified with acceptable tolerances. Spherical radii for both surfaces, if used, will be specified with tolerances. Center thickness is important. Sag for concave and convex surfaces may be given. Alignment of the surfaces with the base in terms of wedge may be specified. Minimum surface figures such as measured with a Zygo interferometer may be listed. Assembly drawings showing all the optical elements in place with spacing between each element specified may be generated by the designer.

6.2

Diamond Turning The advent of diamond point turning for optics was a major advancement. Optical design is a mathematics-based activity. Computer precise control of a diamond point applied to a circular lens blank accurately located on a round rotating mount produced aspheric or diffractive surfaces (kinoforms) on command. Optical designers use software that allows them to specify optical elements in size and shape, using specific optical materials. The refractive index of each material as a function of wavelength is available to the designer in stored tables. The spacing between elements is a variable as well as the center thickness of each lens. The program can calculate expected performance in terms of MTF with spatial frequency on axis and off axis. The variables may then be adjusted slightly to maximize calculated performance for the final design. If the operator could express the surfaces of each lens he or she required mathematically and load it into the computer controlling the diamond point, it would be generated one surface at a time.

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos The initial cost of the diamond point machine was great at first. Since the early 1990s the machines have become much more commonplace, resulting in lower initial cost and more general use. Designs previously impossible to consider are routinely produced but are costly. Costs are estimated in terms of labor hours to set up the machine and labor hours for a technician to tend to the machine as the part is generated, machine time. The diamond turning is carried out at high rotation speeds and under the cover of a cooling fluid continuously sprayed on the rotating part. The process is confined in an enclosure in part to protect the operator.

6.3

Slump Molding Glass has been molded for centuries using simple methods. Generally, the required amount of glass is placed in an open mold and then heated sufficiently for the glass to soften and move under the force of gravity to fill the mold. No pressure is used. Slump molding may be used as a cost-saving measure. Slump molding has been used at TI and AMI to preshape a lens blank to minimize the amount of material removed and wasted during the grinding stage of forming the lens. At AMI, routinely a blank for a deep 7.5-in meniscus Amtir 1 lens has been formed by slumping a flat plate of glass into a concave Pyrex mold. The mold is generated from a Pyrex mirror blank with the concave radius equal to the convex radius of the lens. The plate is placed over the mold and heated in the furnace together until it softens and slumps into the mold under its own weight. After slumping, it is annealed. The thickness of the Amtir 1 plate before slumping is slightly greater than the finished center thickness of the lens. Mostly slump molding is used for shaping glass to dimensions that are not precise.

6.4

Precision Molding The desire to begin precise molding of lenses was a continuation of the goal to lower the cost of infrared optics. The ability to diamond point turn lenses was a real advancement but too expensive. The expense occurred for each lens ordered. The thinking went that if the expense produced a mold instead of one lens, the mold could be used over and over to make many lenses with only the cost of the infrared glass lens blank. The cost of the diamond turning would thus be averaged over many lenses. In 2000, AMI joined with Lockheed Martin in Orlando (LMCO) in a program to develop the technology required to mold infrared lenses from chalcogenide glasses. At this time, the most experienced and knowledgeable person in the United States regarding molding lenses from glass was Harvey Pollicove. His efforts at Eastman Kodak resulted in the development of a production facility

133

134

Chapter Six that molded millions of aspheric camera lenses from silicate-based glasses and plastics. He presented a paper at the SPIE OE/LASE Technical Symposium in January 1988 entitled, “Survey of Present Lens Molding Techniques.” After Pollicove left Kodak, he joined the American Precision Optics Manufacturers Association (APOMA) at the University of Rochester. Many companies were members along with the U.S. Army. Because of the proprietary nature of the AMI effort, a direct inclusion of Pollicove in the AMI program was not possible. Shortly after AMI began the molding program, the author met Harvey Pollicove at a NVL (Night Vision Laboratory) meeting held at the Army Picatinny Arsenal. Later, Pollicove visited at AMI and spent some time with the author. He provided a copy of his paper and many glass molding patents. On return from a trip to Japan, he furnished copies of a technical nature describing automatic systems produced by Toshiba. The information he furnished was very helpful to AMI. The Toshiba units at that time cost $350,000 each, much too expensive for AMI. The units used up to 3500 kg (about 8000 lb) of force, much too severe, we believed, for chalcogenide glasses. The lenses are stamped out. Also, the glass blanks were a sphere of glass heated rapidly in the open. Chalcogenide glasses in contrast to oxide glasses are volatile when heated. Besides being expensive, the method did not seem suited to chalcogenide glasses. Another approach to be considered was injection molding. Miracles have been produced in the injection molding of plastics. The organic thermal plastics lend themselves quite well to the process. Raw materials are powdered or supplied in small pieces, easily heated to form a flowing liquid. However, they are not volatile and not oxidized when exposed to air. Most contain pigments and do not require optical homogeneity. A few attempts were made at AMI to use the glass extruder unit as a source of glass flowing into a mold without any success. The approach was abandoned. AMI decided to develop glasses well suited for the molding process. Low-softening-point glasses were chosen. Lower molding temperatures would increase mold lifetime, a cost factor. Selecting glasses not containing germanium would lower the cost of the glass. Molding at low temperature and pressure should minimize the stress of the molding process which in turn would improve lens quality. An arsenic-selenium glass composition was selected, produced, and characterized optically and physically. The glass, designated Amtir 4, was suitable for use in both the 3- to 5-µm band and the 8- to 12-µm band. Because of its very low dispersion, Amtir 4 can be used as a replacement for germanium parts.1 Amtir 4 has a small negative thermal change in index (−24 × 10−6/°C) in both bands due to a large thermal expansion coefficient. The index change should be contrasted to the over +400 × 10−6/°C for germanium. As a bonus, it was also found that Amtir 4 could be used to draw small-diameter (50-µm core) flexible, unclad bare fibers that improved the quality of IR imaging

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos bundles2 produced at AMI. Later, a second low-softening glass was developed for molding, Amtir 5, similar to Amtir 4 but with a thermal change in refractive index of essentially zero in both the 3- to 5-µm and 8- to 12-µm bands. Also, the glass had a thermal expansion that matches that of aluminum. The glass confirmed an opinion expressed by the author3,4 many years ago that such a unique composition could be selected. The AMI Amtir 5 glass composition is protected by U.S. Patent 6,984,598. Early experiments carried out with Lockheed Martin personnel involved slump molding of Amtir 4 glass using Pyrex spherical molds. Results showed that less than one wave rms was easily achieved on one surface. Attention turned to precision pressure molding. The first AMI unit was built, and efforts turned to developing the molding process. A photograph of the first unit is shown in Fig. 6.1. The design is simple and relatively inexpensive, built from parts obtained locally.

FIGURE 6.1

Photograph of the AMI lens molding unit.

135

136

Chapter Six The large aluminum chamber is equipped with a door that may be sealed, and the chamber evacuated down to a pressure of 50 µm or less. Inside was placed a standard inexpensive programmable oven equipped with a blower to provide circulating air. The temperatures of the molds are controlled using band heaters. The glass blank is placed in the mold, the door is closed, and the unit is evacuated. The molds and glass blank are heated to the molding temperature, and pressure is applied from the cylinder on top of the unit. A few hundred pounds of force is needed for lenses with 1- to 2-in diameter with less than 1000 lb for lenses with almost 6-in diameter. A linear gauge indicates when the molds are closed, indicating the lens is formed. The molds and lens are cooled slightly, the pressure is released, and the unit is vented. After the door is opened, the oven is turned on and the glass anneal cycle is started. As results improved, a plan was devised by LMC to prove the quality of molded chalcogenide glass optics was equal to that of those made by diamond point turning (DPT). A 100-mm FL, F/0.8, 10° field of view, two-element lens was designed using Amtir 4 for use with a LTC 500 LWIR uncooled bolometer array camera produced by a Lockheed Martin company. The front element had a 4.6-in diameter. The convex surfaces of both lenses were spherical. The concave surfaces were aspheric with kinoforms. The first set of optics was diamond turned and coated at AMI. The second was molded and coated at AMI. Amy Graham1 of LMCO showed thermal images that demonstrated that optical performance of the camera using the molded lenses was essentially the same as when using the DPT lenses. Actual physical measurements of two sets of lenses supported this statement (Table 6.1). The only parameter that failed was center thickness CT. The problem was that not enough glass was being removed under current circumstances. The problem was solved by modifying the bottom mold surface so that excess glass was more easily forced out when pressure was applied. Also, the decision was made to use polished blanks that weighed a very small amount greater than the finished lens to minimize glass movement.

Parameter

DPT Part

Molded Part

Delta

R1

1.369

1.369

0.0000

Sag

0.167

0.1674

0.0004

Center thickness

0.326

0.3568

0.0308

Inner diameter

1.529 ± 0.001

1.5245

0.0045

Outer diameter

1.629 + 0.001

1.6255

0.0035

TABLE 6.1

Molded versus Diamond Point Turned Optical Elements

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos

FIGURE 6.2

Infrared image made using the LTC camera with DPT lenses.

Figure 6.2 shows an infrared image produced by the camera using the DPT lenses. The image was made in the AMI parking lot. Notice the fence wire is clearly resolved and the hot tires on the vehicle are prominent. Presently, AMI has only two infrared cameras for experimental use. The first is an Agema 210, a 3- to 5-µm camera that has proved useful in our infrared imaging bundle work. The second is a Raytheon Palm IR BST uncooled bolometer 8- to 12-µm camera that has been most valuable in evaluating lens performance. Both represent early technology and are not considered high-performance cameras. But they were all AMI could afford for this purpose. Adapter plates were required for every different lens we wanted to evaluate. AMI wanted to use the 100-mm molded lens with our 8- to 12-µm camera. Unfortunately, the Palm IR has an optical chopper blade in front of the detector array. The design of the 100-mm lens was for the LTC camera; the back focal length of the camera was too long to be in focus, the lens would hit the light chopper. Fortunately, we could use that same mold with Amtir 5 to shorten the back focal length. Our molding skills had improved to the point we did not hesitate to use different glasses with the same mold. So lens number 1 remained molded with Amtir 4 and lens number 2 was molded with Amtir 5. An adapter plate was made and the lens was placed on the Palm IR. A photograph of the camera with lens is shown in Fig. 6.3. One may notice the coated lens does not look bright and shiny. The reason is the fact the Amtir 4 must be coated at a low temperature

137

138

Chapter Six

FIGURE 6.3 Photograph of molded 100-mm FL Amtir 4-Amtir 5 lenses adapted to the AMI Raytheon Palm IR camera.

because of its low softening point. Coating temperatures above 100°C yield harder, shiny, stronger coatings. Figure 6.4 shows lens 1 molded with both Amtir 5 and Amtir 6 (As2S3) glasses. Note the one on the right is Amtir 5 with an antireflection coating. The one on the left is

FIGURE 6.4

Photograph of 100-mm FL lens 1 molded with Amtir 5 and 6.

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos uncoated and shows its natural color. Note the kinos on both are clearly visible. AMI also worked with Jan Terlow and John Lawson of CBC America to mold four elements used in an IR zoom lens. The lens changes from an F/0.8 to F/1.2. Three of the lenses are spherical convex with kinoforms on the concave side. The fourth element is double concave with one spherical and one aspheric with a kinoform. The original design used Amtir 4, but as our molding skills improved, we found we could mold the elements with Amtir 5. For the same optical performance, only one element design needed to change going from Amtir 4 to Amtir 5. Again, a mounting plate for the Palm IR camera was constructed so that we could use the zoom with the camera. Figure 6.5 shows the zoom mounted on the Palm IR camera. Further examples of using the same mold with different glasses are seen in Fig. 6.6. Lens 1 of the zoom is shown molded using Amtir 5, Amtir 6, and C1 glass. The lenses are uncoated. Again, the Amtir 6 lens shows its true color. Kinos are clearly visible on all three. Two sets of DPT Amtir 4 optics were made during the Lockheed Martin IRAD for a two-element design with a 218-mm focal length. AMI provided one of the lens mounts and antireflection-coated both sets. LMCO kept one set and AMI the other. Lens 1 had a 5.7-in diameter while lens 2 had a 1.8-in diameter. The lenses with mounting are very heavy. An adapter plate was made so the lens could be used on the AMI Palm IR. A support was made for camera and lens. Figure 6.7 shows

FIGURE 6.5 CBC America IR Zoom made with molded Amtir 4 glass lenses mounted on the Raytheon Palm IR camera.

139

140

Chapter Six

FIGURE 6.6 Photograph of zoom lens 1 molded using Amtir 5, Amtir 6, and the As-Se-Te C1 core glass.

FIGURE 6.7 Photograph of Amtir 4 two-element 218-mm FL lens adapted to the AMI Palm IR camera.

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos the camera and lens with support mount at the local high school track used by the author each week usually at 5 a.m. The performances of the lenses described with the Palm IR camera are shown by the figures that follow. Figure 6.8 shows the images produced by the CBC America Zoom IR lens mounted on the Palm IR camera. The top image is in the narrow field mode, and the bottom is the wide field mode image. The object is a person in a darkened warehouse 160 ft from the camera. He is standing between two machines against the back wall. The machinery

FIGURE 6.8 Photographs demonstrating the performance of the CBC America Zoom IR lens mounted on the Palm IR camera.

141

142

Chapter Six

FIGURE 6.9 Photograph demonstrating the performance of the molded Amtir 4-Amtir 5 100-mm FL IR lens mounted on the Palm IR camera.

is not visible at all in the narrow mode but shows up slightly in the wide field. Figure 6.9 shows a photograph taken of the same scene only using the molded Amtir 4-Amtir 5 100-mm FL IR lens again mounted on the Palm IR camera. Notice the machinery against the wall is now clearly visible. The image of the person is larger and more detailed. Figure 6.10 shows in the bottom photograph a visible image of the high school track. Look closely and you will see a small white image of a person at the far end of the track. The person is about 170 yd from the camera. The top image was taken using the 218-mm IR lens mounted on the Palm IR very early in the morning. The cool background makes the warm person very visible as a white object. The person is the author. In this case, the camera was on a tripod aimed at the distant location. The camera was turned on, and the author walked to the distant point. Being alone made best focus adjustments impossible. Nevertheless, the shape of a person was clearly distinguishable. The composition of Amtir 5 was precisely selected to provide a near-zero thermal change in refractive index in both bands, 3 to 5 µm and 8 to 12 µm. The unique value of Amtir 5 was the fact that athermal systems can be designed and built without the need for mechanical thermal compensating parts. Such devices were an extra complication and expense to infrared system designers. After the glass was developed, LMCO built a wide field of view airborne system and confirmed by Dan Woody of LMCO a less than 1 percent change in

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos

FIGURE 6.10 Photograph demonstrating the performance of the DPT Amtir 4 218-mm FL IR lens mounted on the Palm IR camera.

performance during temperature excursions. The decision was made to use Amtir 5 in the infrared system for the new Joint Strike Fighter. As part of the IRAD, AMI molded several of the 5.38-in-diameter lenses. The convex and concave surfaces were both spherical. A photograph of one of the molded lenses is shown in Fig. 6.11. Another question in molding that has not been mentioned is, How do you get the molded part out of the mold without it being broken? It is true the molds are usually coated with a thin film to which the glass part should not stick. However, these coatings develop open spots with use. Also, some areas of the mold are almost impossible to reach while coating. Another factor can be the shape and fragile nature of a lens.

143

144

Chapter Six

FIGURE 6.11

Photograph of a molded 5.38-in-diameter Amtir 5 JSF lens.

AMI found itself in a seemingly impossible situation when an agreement was made to mold a lens 8 mm in diameter. Early attempts proved fruitless. Another approach was needed. We decided to place a thin metal ring in the mold, the outside diameter the same as the bottom of the mold and the height of the ring the same as the lens edge, so the glass would bond to the ring. The lens could then be removed because the metal ring would not stick to the metal mold. The scheme worked, and the 8-mm lens fell right out. Figure 6.12 shows a fuzzy photo of the 8-mm molded lens encased in the metal ring at the base. Figure 6.13 shows a diagram of the scheme we followed. Another example is shown in Fig. 6.14. In this case, a fragile

FIGURE 6.12

Photograph of a molded 8-mm-diameter lens in a metal ring.

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos Top mold, convex surface

IR glass blank Metal ring

Bottom mold, concave surface

Molded IR lens with attached metal ring

FIGURE 6.13 Diagram of the metal ring procedure used to reduce the difficulty in removing a molded lens from the mold.

FIGURE 6.14

Photograph of a molded 17-mm-diameter lens in metal ring.

145

146

Chapter Six tophat-shaped 17-mm-diameter lens was molded in a metal ring. The procedure increased the yield of the molding process substantially. Also, the ring protects the glass from edge fractures.

6.5 Volume Production From the very start in the molding effort, AMI has been more interested in producing quality lenses based on the glasses we produce. We developed molding units and antireflection coatings compatible with chalcogenide glasses. Rapid stamping out of lenses from chalcogenide glasses was rejected. The AMI molding process uses low pressure and takes time. There are 5 units installed in the production area as shown in Fig. 6.15. All are the same and constructed here with local help and component parts. The goal here was simple inexpensive units. With two operators, each unit may be used twice per day to go through a complete cycle. On that basis, it is possible the 5 units could produce 10 lenses per day, 50 lenses per week, or about 2600 lenses per year. To increase production volume even further, there is enough room in this area to place another 5 or even 10 units in place. One factor not mentioned is molds and their cost. The value of the business would have to support the cost of the new units and the great expense of molds for all the units, sometimes $10,000 per set.

FIGURE 6.15

Photograph of five AMI molding units in the production area.

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos

FIGURE 6.16

Photograph of a mounted mold pair with alignment pins.

Another approach, for smaller lenses, is multimolding. The AMI mounting plates are large and could accommodate several lens molds. Figure 6.16 shows how the large molding plates with alignment pins to ensure top and bottom molds match. Figure 6.17 shows eight molds

FIGURE 6.17

Photograph of mounted multimolds top and bottom.

147

148

Chapter Six for the same small lens in place both top and bottom. This approach is much more productive from the standpoint of the number of operators and molding units. Mold cost will still be a major factor. The business volume must be there to support the effort. Now, AMI is often asked about producing parts in terms of a hundred thousand or more. Our molding approach will lend itself to producing hundreds or a few thousand perhaps, but not a hundred thousand. A small independent company such as Amorphous Materials lacks the resources and the desire for such an undertaking.

6.6

Problem of Refractive Index Change When Pressure Molding When a glass is pressure-molded, it must be heated above its glass transition temperature. One must remember that below that temperature, glass acts as a solid and will break if pressure is applied to reshape it. As for any liquid, if enough pressure is applied, the liquid is very slightly compressed. Since refractive index is a measure of the concentration of atoms per centimeter cubed, the index increases in a positive sense. In optics, a small change in refractive index is important, The change needs to be measured to see how large a problem exists. Also, a way to avoid the problem may be found.

AMI Infrared Refractometer Previous discussions concerning the AMI infrared refractometer have pointed out that measurements of a single prism in a single orientation are reproducible to a small number in the fourth decimal place. In each instance of the data presented, the prism has been removed and measured in the same orientation on different days. The data presented in Table 6.2 support the claimed accuracy. Previous discussions have pointed out that the lack of perfection in the fabricated prism is overcome by measuring the prism in each of

Date

N @ 3 µm

N @ 4 µm

N @ 5 µm

8/4/04

2.7616

2.7565

2.7533

8/6/04

2.7621

2.7569

2.7535

8/9/04

2.7621

2.7565

2.7534

Average

2.7619

2.7566

2.7534

±0.00016

±0.00016

±0.00007

TABLE 6.2

Amtir 5 Prism 03-1B, Orientation LD

Unconventional Lens Fabrication, Aspheric Surfaces, and Kinos

After Standard

After Modified

Before Molding

Molding Proc.



Molding Proc.



3

2.7575

2.7622

+0.0047

2.7575

+0.0000

4

2.7530

2.7568

+0.0038

2.7523

−0.0007

5

2.7493

2.7534

+0.0041

2.7488

−0.0005

8

2.7426

2.7466

+0.0040

2.7421

−0.0005

10

2.7379

2.7418

+0.0039

2.7372

−0.0007

λ (µm)

TABLE 6.3

Change in Index on Molding Amtir 5

four orientations on the mirror, left or right relative to the beam (L or R) and up or down for the top of the prism (U or D). The four measurements averaged lead to the accurate value, as has been demonstrated a number of times for materials where the resulting values are compared to those published by NBS or NIST. To demonstrate the change in index on molding Amtir 5, we have taken the before-and-after approach (Table 6.3). A prism was fabricated from annealed glass from plate 04-23 and measured 3 to 10 µm in all four orientations. Next, glass from the plate was used to mold a flat 5-in-diameter plate using our standard temperature and pressure. A prism was fabricated from the plate and measured in an identical manner. Then a second plate was molded at the same temperature and pressure, only care was taken to release the pressure at a point above the Tg in order to relax the compressed liquid. In conclusion, molding under pressure will increase the refractive index appreciably, 0.0040. However, if the pressure is released before the glass becomes a solid, the change is small, < 0.0010. In summary,5 AMI has developed the technology to mold highquality lenses from glasses produced by AMI. Two low-softening glasses developed were successfully used for molding. Antireflection coatings were developed for these glasses. Lenses made using Amtir 4 and 5 are in several important military systems. AMI has applied the knowledge learned to mold four of the seven glasses produced by AMI shown in Table 6.4. Amtir 1 has not been molded because of its high softening temperature of 405°C. Amtir 2 is a very likely candidate because of its similarity to Amtir 5. Amtir 4, not listed, is not fully developed at this time. Amtir 4 is better than Amtir 1 in transmitting visible light. The softening point of Amtir 4 is 277°C, well over 100° lower than Amtir 1. Amtir 4 is a good candidate for molding. AMI has established production capability with five molding production units.

149

150

Chapter Six

Property

Amtir 1 Amtir 2 Amtir 3 Amtir 4 Amtir 5 Amtir 6 C1

Composition

Ge-AeSe

As-Se

Ge-Sb-Se As-Se

As-Se

As-S

Transmission 0.7–12 1.0–14 1.0–12 1.0–12 1.0–12 0.6–8 range (µm)

As-Se-Te 1.2–14

Ref. index at 10 µm

2.4981 2.7691 2.6027 2.6431 2.7398 2.3807 2.8051

∆N/∆T (°C × 10–6)

72

5

91

−23