5,529 438 37MB
Pages 799 Page size 595 x 842 pts (A4) Year 2011
An Introduction to Applied and Environmental Geophysics
An Introduction to Applied and Environmental Geophysics
JOHN M. REYNOLDS Reynolds Geo-Sciences Ltd, UK
JOHN WILEY & SONS Chichester' New York· Weinheim . Brisbane' Singapore' Toronto
?c
"f //~opyright
1997 by John M. Reynolds
Published 1997 by John Wiley & Sons Ltd, Baffins Lane, Chichester, West Sussex POl9 IUD, England National 01243779777 International (+ 44) 1243779777 e-mail (for orders and customer service enquiries): cs-books (II wiley.co.uk Visit our Home Page on http://www.wiley.co.uk or http://www.wiley.com Reprinted February 1998 All Rights Reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, scanning or otherwise, except under the terms of the Copyright, Designs and Patents Act 1988 or under the terms of a licence issued by the Copyright Licensing Agency, 90 Tottenham Court Road, London, UK WI P 9HE, without the permission in writing of the publisher, and the copyright owner. Other Wiley Editorial Offices
John Wiley & Sons, Inc., 605 Third Avenue, New York, NY 10158-0012, USA VCH Verlagsgesellschaft mbH Pappelallee 3, D-69469 Weinheim, Germany Jacaranda Wiley Ltd, 33 Park Road, Milton, Queensland 4064, Australia John Wiley & Sons (Canada) Ltd, 22 Worcester Road, Rexdale, Ontario M9W ILl, Canada John Wiley & Sons (Asia) Pte Ltd, 2 Clementi Loop #02-01, Jin Xing Distripark, Singapore 129809 Library ofConf:ress Catalof:inf:-in-Publication Data
Reynolds, John M. An introduction to applied and environmental geophysics / by John M. Reynolds. p. em. Includes bibliographical references and index. ISBN 0-471-96802-I.-ISBN 0-471-95555-8 (pbk) I. Geophysics-Technique. 2. Seismology Technique. I. Title. QC808.5.R49 1997 97-14061 551'.028-dc20 CIP British Library Catalof:uinf: in Publication Data
A catalogue record for this book is available from the British Library ISBN
0-471-96802-1 (cloth) 0-471-95555-8 (pbk)
Typeset in 10/12pt Times by Thomson Press (India) Ltd., New Delhi Printed and bound in Great Britain by Bookcraft (Bath) Ltd, Midsomer Norton, Somerset This book is printed on acid-free paper responsibly manufactured from sustainable forestation, for which at least two trees are planted for each one used for paper production.
Contents vii
Preface 1.
Introduction
SECTION 1
2. 3.
POTENTIAL FIELD METHODS
Gravity methods Geomagnetic methods
SECTION 2
APPLIED SEISMOLOGY
4. Applied seismology: introduction and principles 5. Seismic refraction surveying 6. Seismic reflection surveying SECTION 3 7.
8. 9.
Electrical resistivity methods Spontaneous (self) potential methods Induced polarisation
SECTION 4
10. 11.
12.
ELECTRICAL METHODS
ELECTROMAGNETIC METHODS
Electromagnetic methods: introduction and principles Electromagnetic methods: systems and applications Ground penetrating radar
1 29
31 116 209
211 276 321 415
417 491
522 553 555 586 681
References
750
Index
778
Preface The idea for this book originated in 1987 whilst T was preparing for lectures on courses in applied geology and environmental geophysics at Plymouth Polytechnic (now the University of Plymouth), Devon, England. Students who had only very basic mathematical skills and little if any physics background found most ofthe so-called 'introductory' texts difficult to follow owing to the perceived opacity of text and daunting display of apparently complex mathematics. To junior undergraduates, this is immediately offputting and geophysics becomes known as a 'hard' subject and one to be avoided at all costs. I hope that the information on the pages that follow will demonstrate the huge range of applications of modern geophysics - some now very well established, others very much in the early stages of implementation. It is also hoped that the book will provide a foundation on which to build if the reader wishes to take the subject further. The references cited, by no means exhaustive, have been included to provide pointers to more detailed discussions. The aim of this book is to provide a basic introduction to geophysics, keeping the mathematics and theoretical physics to a minimum and emphasising the applications. Considerable effort has been expended in compiling a representative set of case histories that demonstrate clearly the issues being discussed. This book is different from other introductory texts in that it pays attention to a great deal of new material, or topics not previously discussed in detail: for example, geophysical survey design and line optimisation techniques, image-processing of potential field data, recent developments in high-resolution seismic reflection profiling, electrical resistivity Sub-Surface Imaging (tomography), Spectral Induced Polarisation, and Ground Penetrating Radar, amongst many other subjects, which until now have never featured in detail in such a book. Many new and previously unpublished case histories from commercial projects have been included along with recently published examples of applications. The subject material has been developed over a number of years, firstly while I was at Plymouth, and secondly and more recently while
viii
Pr~race
I have been working as a geophysical consultant. Early drafts of the book have been tried out on several hundred second- and third-year students who have been unwitting 'guinea pigs' - their comments have been very helpful. While working in industry, I have found the need for an introductory book all the more evident. Many potential clients either appear unaware of how geophysics could possibly be of help to them, or have a very dated view as to the techniques available. There has been no suitable book to recommend to them that explained what they needed and wanted to know or that provided real examples. While I have been writing this book, the development of new instruments, improved data-processing and interpretation software and increased understanding of physical processes have been unparalleled in the history of geophysical sciences. It has been difficult to keep abreast of all the new ideas, especially with an ever-increasing number of scientific publications. What is exciting is that the changes are still occurring and we can expect to see yet more novel developments over the next few years. We may see new branches of the science develop, particularly in environmental geophysics and applications to contaminated-land mapping, for example. It is my hope that this book will be seen as providing a broad overview of applied and environmental geophysics methods, illustrating the power and sophistication ofthe various techniques, as well as their limitations. If this book helps in improving the acceptance of geophysical methods and in increasing the awareness of the methods available, then it will have met its objective. There is no doubt that applied and environmental geophysics have an important role to play, and that the potential for the future is enormous. It is inevitable with a book of this kind that brand names, instrument types, and specific manufacturers are named. Reference to such information does not constitute an endorsement of any product and no preference is implied, nor should any inference be drawn over any omissions. In books of this type the material covered tends to be flavoured by the interests and experiences ofthe author, and I am sure that this one is no exception. I hope that what is included is a fair reflection ofthe current state of applied and evironmental geophysics. Should any readers have any case histories that they feel are of particular significance, I should be most interested to receive them for possible inclusion at a later date. Also, any comments or corrections that readers might have would also be gratefully received.
ACKNOWLEDGEMENTS Drafts of the manuscript have been read by many colleagues, and their help, encouragement and advice have been most beneficial. I would particularly like to thank Professor Don Tarling for his
Preface
continual encouragement to complete this book and for having commented on substantial parts of the manuscript. Thanks are also due to companies that have very kindly supplied material, and to colleagues around the world for permitting extracts of their work to be reproduced. I must also thank Richard Baggaley (formerly of the Open University Press) for commissioning me to write the book in the first place, and to Helen Bailey, Abi Hudlass and Louise Portsmouth at John Wiley for their patience in waiting so long for the final manuscript. My final acknowledgement must be to my wife, Moira, and sons, Steven and David, for their support, encouragement and longsuffering patience while I have been closeted with 'The Book', Without their help and forbearance, this project would have been abandoned long ago. John M. Reynolds Mold, Clwyd, North Wales, UK June 1995
IX
Chapter 1 Introduction 1.1 1.2 1.3 1.4
What are 'applied' and 'environmental' geophysics? Geophysical methods Matching geophysical methods to applications Planning a geophysical survey 1.4.1 1.4.2 1.4.3
1.5
General philosophy Planning strategy Survey constraints
1 4 5 8 8 9 9
Geophysical survey design
13
1.5.1 1.5.2 1.5.3 1.5.4 1.5.5
13 15 17 20 25
Target identification Optimum line configuration Selection ()f station intervals Noise Data analysis
Bibliography General geophysics texts Further reading
26 26 27
1.1 WHAT ARE 'APPLIED' AND 'ENVIRONMENTAL' GEOPHYSICS? In the broadest sense, the science of Geophysics is the application of physics to investigations ofthe Earth, Moon and planets. The subject is thus related to astronomy. Normally, however, the definition of 'Geophysics' is used in a more restricted way, being applied solely to the Earth. Even then, the term includes such subjects as meteorology and ionospheric physics, and other aspects of atmospheric sciences. To avoid confusion, the use of physics to study the interior of the Earth, from land surface to the inner core, is known as Solid Earth Geophysics. This can be subdivided further into Global Geophysics, or alternatively Pure Geophysics, which is the study of the whole or
2
An introduction to applied and environmental geophysics
substantial parts of the planet, and Applied Geophysics which is concerned with investigating the Earth's crust and near-surface to achieve a practical and, more often than not, an economic aim. 'Applied geophysics' covers everything from experiments to determine the thickness of the crust (which is important in hydrocarbon exploration) to studies of shallow structures for engineering site investigations, exploring for groundwater and for minerals and other economic resources, to trying to locate narrow mine shafts or other forms of buried cavities, or the mapping of archaeological remains, or locating buried pipes and cables - but where in general the total depth of investigation is usually less than 100 m. The same scientific principles and technical challenges apply as much to shallow geophysical investigations as to pure geophysics. Sheriff(1991; p. 139) has defined 'applied geophysics' thus: "Making and interpreting measurements of physical properties of the earth to determine sub-surface conditions, usually with an economic objective, e.g., discovery of fuel or mineral depositions."
'Engineering geophysics' can be described as being: 'The application of geophysical methods to the investigation of sub-surface materials and structures which are likely to have (significant) engineering implications."
As the range of applications of geophysical methods has increased, particularly with respect to derelict and contaminated land investigations, the sub-discipline of 'environmental geophysics' has developed (Greenhouse 1991; Steeples 1991). This can be defined as being: 'The application of geophysical methods to thc investigation of near-surface physico-chemical phenomena which are likely to have (significant) implications for the management of the local environment."
The principal distinction between engineering and environmental geophysics is more commonly that the former is concerned with structures and types of materials, whereas the latter can also include, for example, mapping variations in pore-fluid conductivities to indicate pollution plumes within groundwater. Chemical effects are equally as important as physical phenomena. Since the mid-1980s in the UK, geophysical methods have been used increasingly to investigate derelict and contaminated land, with a specific objective of locating polluted areas prior to direct observations using trial pits and boreholes (e.g. Reynolds and Taylor 1992). Geophysics is also being used much more extensively over landfills and other waste repositories (e.g. Reynolds and McCann 1992). One ofthe advantages of using geophysical methods is that they are largely environmentally
4
An introduction to applied and environmental geophysics
(geophysics in glaciology). The last one is the least well known, despite the fact that it has been in existence for far longer than either archaeoor environmental geophysics, and is particularly well established within the polar scientific communities and has been since the 1950s. The general orthodox education of geophysicists to give them a strong bias towards the hydrocarbon industry has largely ignored these other areas of our science. It may be said that this restricted view has delayed the application of geophysics more widely to other disciplines. Geophysics has been taught principally in Earth Science departments of universities. There is an obvious need for it to be introduced to engineers and archaeologists much more widely than at present. Similarly, the discipline of environmental geophysics needs to be brought to the attention of policy-makers and planners, to the insurance and finance industries (Doll 1994). The term 'environmental geophysics' has been interpreted by some to mean geophysical surveys undertaken with environmental sensitivity - that is, ensuring that, for example, marine seismic surveys are undertaken sympathetically with respect to the marine environment (Bowles 1990). With growing public awareness of the environment and the pressures upon it, the geophysical community has had to be able to demonstrate clearly its intentions to minimise environmental impact (Marsh 1991). By virtue of scale, the greatest likely impact on the environment is from hydrocarbon and some mineral exploration, and the main institutions involved in these activities are well aware of their responsibilities. In small-scale surveys the risk of damage is much lower; but all the same, it is still important that those undertaking geophysical surveys should be mindful of their responsibilities to the environment and to others whose livelihoods depend upon it. While the term 'applied geophysics' covers a wide range of applications, the importance of 'environmental' geophysics is particularly highlighted within this book. The growth of the discipline, which appears to be expanding exponentially, is such that this subject may outstrip the use of geophysics in hydrocarbon exploration during the early part of the next century and provide the principal area of employment for geophysicists. Whether this proves to be the case is for history to decide. What is clear, however, is that even in the last decade of this century, environmental geophysics is becoming increasingly important in the management of our environment. Ignore it at your peril!
1.2
GEOPHYSICAL METHODS
Geophysical methods respond to the physical properties of the sub-surface media (rocks, sediments, water, voids, etc.) and can be classified into two distinct types.
Introduction
• Passive methods are those that detect variations within the natural fields associated with the Earth, such as the gravitational and magnetic fields . • In contrast are the active methods, such as those used in exploration seismology, in which artificially generated signals are transmitted into the ground, which then modifies those signals in ways that are characteristic of the materials through which they travel. The altered signals are measured by appropriate detectors whose output can be displayed and ultimately interpreted. Applied geophysics provides a wide range of very useful and powerful tools which, when used correctly and in the right situations, will produce useful information. All too~s, if misused or abused, will not work effectively. One of the aims of this book it to try to explain how applied geophysical methods can be employed appropriately, and to highlight the advantages and disadvantages of the various techniques. Geophysical methods may form part of a larger survey, and thus geophysicists should always try to interpret their data and communicate their results clearly to the benefit of the whole survey team and particularly to the client. An engineering site investigation, for instance, may require the use of seismic refraction to determine how easy it would be to excavate the ground (e.g. the 'rippability' of the ground). If the geophysicist produces results that are solely in terms of seismic velocity variations, the engineer is still none the wiser. The geophysicist needs to translate the velocity data into a rippability index with which the engineer would be familiar. Few, if any, geophysical methods provide a unique solution to a particular geological situation. It is possible to obtain a very large number of geophysical solutions to some problems, some of which may be geologically nonsensical. It is necessary, therefore, always to ask the question: "Is the geophysical model geologically plausible?" If it is not, then the geophysical model has to be rejected and a new one developed which does provide a reasonable geological solution. Conversely, if the geological model proves to be inconsistent with the geophysical interpretation, then it may require the geological information to be re-evaluated. It is of paramount importance that geophysical data are inter-
preted within a physically constrained or geological framework.
1.3 MATCHING GEOPHYSICAL METHODS TO APPLICATIONS The various geophysical methods rely on different physical properties and it is important that the appropriate technique be used for a given type of application.
v'
5
8
An introduction to applied and environmental geophysics
very clearly in respect to a geomagnetic anomaly over Lausanne in Switzerland (Figure 1.2). While the model with the form of a question mark satisfies a statistical fit to the observed data, the model is clearly and quite deliberately geological nonsense in order to demonstrate the point. However, geophysical observations can also place stringent restrictions on the interpretation of geological models. While the importance of understanding the basic principles cannot be over-emphasised, it is also necessary to consider other factors that affect the quality and usefulness of any geophysical survey, or for that matter of any type of survey whether it is geophysical, geochemical or geotechnical. This is done in the following few sections.
1.4 PLANNING A GEOPHYSICAL SURVEY 1.4.1
General philosophy
Any geophysical survey tries to determine the nature of the subsurface, but it is of paramount importance that the prime objective of the survey be clear right at the beginning. The constraints on a commercial survey will have emphases different from those on an academic research investigation and, in many cases, there may be no ideal method. The techniques employed and the subsequent interpretation of the resultant data tend to be compromises, practically and scientifically. There is no short-cut to developing a good survey style; only by careful survey planning backed by a sound knowledge of the geophysical methods and their operating principles, can cost-effective and efficient surveys be undertaken within the prevalent constraints. However, there have been only a few published guidelines - e.g. British Standards Institute BS 5930 (1981), Hawkins (1986), Geological Society Engineering Group Working Party Report on Engineering Geophysics (1988). Scant attention has been paid to survey design, yet a badly thought-out survey rarely produces worthwhile results. Indeed, Darracott and McCann (1986, p. 85) said that: "dissatisfied clients have frequently voiced their disappointment with geophysics as a site investigation method. However, close scrutiny of almost all such cases will show that the geophysical survey produced poor results for one or a combination of the following reasons: inadequate and/or bad planning of the survey; incorrect choice or specification of technique, and insufficiently experienced personnel conducting the investigation." It is hoped that this chapter will provide at least a few pointers to help construct cost-effective and technically sound geophysical field programmes.
Introduction
1.4.2
Planning strategy
Every survey must be planned according to some strategy, or else it will become an uncoordinated muddle. The mere acquisition of data does not guarantee the success of the survey. Knowledge (by way of masses of data) does not automatically increase our understanding of a site; it is the latter we are seeking, and knowledge is the means to this. One less-than-ideal approach is the 'blunderbus' approach - take along a sufficient number of different methods and try them all out (usually inadequately owing to insufficient testing time per technique) to see which ones produce something interesting. Whichever method yields an anomaly, then use that technique. This is a crude statistical approach, such that if enough techniques are tried then at least one must work! This is hardly scientific or cost-effective. The success of geophysical methods can be very site-specific and scientifically-designed trials of adequate duration may be very worthwhile to provide confidence that the techniques chosen will work or that the survey design needs modifying in order to optimise the main survey. It is in the interests of the client that suitably experienced geophysical consultants are employed for the vital survey design, site supervision and final reporting. So what are the constraints that need to be considered by both clients and geophysical survey designers? An outline plan of the various stages in designing a survey is given in Figure 1.3. The remainder of this chapter discusses the relationships between the various components.
1.4.3 Survey constraints
The first and most important factor is that of finance. How much is the survey going to cost and how much money is available? The cost will depend on where the survey is to take place, how accessible the proposed field site is, and on what scale the survey is to operate. An airborne regional survey is a very different proposition to, say, a local, small-scale ground-based investigation. The more complex the survey in terms of equipment and logistics, the greater the cost is likely to be. It is important to remember that the geophysics component of a survey is usually only a small part of an exploration programme and thus the costs of the geophysics should be viewed in relation to those of the whole project. Indeed, the judicious use of geophysics can save large amounts of money by enabling the effective use of resources (Reynolds 1987a). For example, a reconnaissance survey can identify smaller areas where much more detailed investigations ought to be undertaken - thus removing the need to do saturation surveying. The factors that influence the various components of a budget also vary
9
10
An introduction to applied and environmental geophysics
SURVEY OBJECTIVES
IBU/~li~1 SURVEY DESIGN SPECIFICATION
GEOPHYSICAL SPECIFICATION
~~ WHICH METHODS? Electrical/magnetic/ electromagnetic/etc.
Line orientation Station interval Survey optimisation
Position fixing
DATA ACQUISITION
DATA STORAGE Manual Datalogger ROM memory
from country to country, and from job to job, and there is no magic formula to guarantee success. Some of the basic elements of a survey budget are given in Table 1.2. This list is not exhaustive but serves to highlight the most
Figure 1.3 Schematic flow diagram to illustrate the decision-making process leading to the selection of geophysical and utility software. From Reynolds (1991a), by permission
Introduction
Table 1.2 Basic elements of a survey budget Staffing Operating costs Cashflow Equipment Insurance Overheads Development costs Contingencies
Management, technical, support, administration, etc. Including logistics Assets versus usable cash For data acquisition and/or for data reduction/analysis - computers and software; whether or not to hire or buy To include liability insurance, as appropriate Administration; consumables; etc. Skills, software, etc. Something is bound to go wrong at some time, usually when it is most inconvenient!
common elements of a typical budget. Liability insurance is especially important if survey work is being carried out as a service to others. If there is any cause for complaint, then this may manifest itself in legal action (Sherrell 1987). It may seem obvious to identify logistics as a constraint but there have been far too many surveys ruined by a lack ofeven the most basic needs of a survey. It is easy to think of the main people to be involved in a survey - i.e. geologists, geophysicists, surveyors - but there are many more tasks to be done to allow the technical staff the opportunity to concentrate on the tasks in hand. Vehicles and equipment will need maintaining, so skilled technicians and mechanics may be required. Everybody has to eat and it is surprising how much better people work when they are provided with well-prepared food: a good cook at base camp can be a real asset. Due consideration should be paid to health and safety and any survey team should have staff trained in First Aid. Admittedly it is possible for one person to be responsible for more than one task, but on large surveys this can prove to be a false economy. Apart from the skilled and technical staff, local labour may be needed as porters, labourers, guides, translators, etc., or even as armed guards! It is all too easy to forget what field conditions can be like in remote and inaccessible places. It is thus important to remember that in the case of many countries, access in the dry season may be possible whereas during the rains of the wet season, the so-called roads (which often are dry river beds) may be totally impassable. Similarly, access to land for survey work can be severely hampered during the growing season with some crops reaching 2-3 metres high and consequently making position fixing and physical access extremely difficult. There is then the added complication that some surveys, such as seismic refraction and reflection, may cause a limited amount of damage for which financial compensation may be sought. In some cases, claims may be made even when no damage has been caused! If year-round access is necessary the provision of all-terrain vehicles and/or helicopters may prove to be the only option, and these are never cheap to operate.
11
12
An introduction to applied and environmental geophysics
Where equipment has to be transported, consideration has to be given not only to its overall weight but to the size of each container. It can prove an expensive mistake to find that the main piece of equipment will not pass through the doorway of a helicopter so that alternative overland transport has to be provided at very short notice; or to find that many extra hours of flying time are necessary to airlift all the equipment. It may even be necessary to make provision for a bulldozer to excavate a rough road to provide access for vehicles. If this is accounted for inadequately in the initial budgeting, the whole success of the survey can be jeopardised. Indeed, the biggest constraint in some developing countries, for example, is whether the equipment can be carried by a porter or will fit on the back of a packhorse. Other constraints that are rarely considered are those associated with politics, society and religion. Let us take these in turn. Political constraints This can mean gaining permission from landowners and tenants for access to land, and liaison with clients (which often requires great diplomacy). The compatibility of staff to work well together also needs to be considered, especially when working in areas where there may be conflicts between different factions of the local population - such as tribal disputes or party political disagreements. It is important to remember to seek permission from the appropriate authority to undertake geophysical fieldwork. For example, in Great Britain it is necessary to liaise with the police and local government departments if survey work along a major road is being considered, so as to avoid problems with traffic jams. In other cases it may be necessary to have permission from a local council, or in the case of marine surveys, from the local harbour master so that appropriate marine notices can be issued to safeguard other shipping. All these must be found out well before the start of any fieldwork. Delays cost money! Social constraints For a survey to be successful it is always best to keep on good terms with the local people. Treating other people with respect will always bring dividends (eventually). Each survey should be socially and environmentally acceptable and not cause a nuisance. An example is in not choosing to use explosives as a seismic source for reflection profiling through urban areas or at night. Instead, the seismic vibrator technique should be used (see Chapter 4). Similarly, an explosive source for marine reflection profiling would be inappropriate in an area associated with a lucrative fishing industry because of possibly unacceptably high fish-kill. In designing the geophysical survey, the question must be asked: "Is the survey technique socially and environmentally acceptable?"
Introduction
Religious constraints The survey should take into account local social customs which are often linked with religion. In some Muslim countries, for example, it is common in rural areas for women to be the principal water-collectors. It is considered inappropriate for the women to have to walk too far away from the seclusion of their homes. Thus there is no point in surveying for groundwater for a tubewell several kilometres from the village (Reynolds 1987a). In addition, when budgeting for the provision oflocal workers, it is best to allow for their 'sabbath'. Muslims like to go to their mosques on Friday afternoons and are thus unavailable for work then. Similarly, Christian workers tend not to like being asked to work on Sundays, or Jews on Saturdays. Religious traditions must be respected to avoid difficulties. However, problems may come iflocal workers claim to be Muslims on Fridays and Christians on Sundays - and then that it is hardly worth anyone's while to have to work only on the Saturday in between so they end up not working Friday, Saturday or Sunday! Such situations, while sounding amusing, can cause unacceptable delays and result in considerably increased survey costs.
1.5 GEOPHYSICAL SURVEY DESIGN 1.5.1
Target identification
Geophysical methods locate boundaries across which there is a marked contrast in physical properties. Such a contrast can be detected remotely because it gives rise to a geophysical anomaly (Figure 1.4) which indicates variations in physical properties relative to some background value (Figure 1.5). The physical source of each anomaly is termed the geophysical target. Some examples of targets are trap structures for oil and gas, mineshafts, pipelines, ore lodes, cavities, groundwater, buried rock valleys, and so on. In designing a geophysical survey, the type of target is of great importance. Each type of target will dictate to a large extent the appropriate geophysical method(s) to be used, and this is where an understanding of the basic geophysical principles is important. The physical properties associated with the geophysical target are best detected by the method(s) most sensitive to those same properties. Consider the situation where saline water intrudes into a nearsurface aquifer; saline water has a high conductivity (low resistivity) in comparison with freshwater and so is best detected using electrical resistivity or electromagnetic conductivity methods; gravity methods would be inappropriate because there would be virtually no density contrast between the saline and freshwater. Similarly, seismic methods would not work as there is no significant difference in seismic wave velocities between the two saturated zones. Table 1.1
13
Section 1 POTENTIAL FIELD METHODS
Chapter 2 Gravity methods 2.1 2.2
Introduction Physical basis 2.2.1 Theory 2.2.2 Gravity units 2.2.3 Variation of gravity with latitude 2.2.4 Geological factors affecting density 2.3 Measurement of gravity 2.3.1 Absolutegravity 2.3.2 Relative gravity 2.4 Gravity meters 2.4.1 Stable (static) gravimeters 2.4.2 Unstable ( astatic) gravimeters 2.5 Corrections to gravity observations 2.5.1 Instrumental drift 2.5.2 Tides 2.5.3 Latitude 2.5.4 Free-air correction 2.5.5 Bouguer correction 2.5.6 Terrain correction 2.5.7 Eotvos correction 2.5.8 I sostatic correction 2.5.9 Miscellaneous factors 2.5.10 Bouguer anomaly 2.6 Interpretation methods 2.6.1 Regionals and residuals 2.6.2 Anomalies due to different geometric forms 2.6.3 Depth determinations 2.6.4 Mass determination 2.6.5 Second derivatives 2.6.6 Sedimentary basin or granite pluton? 2.7 Applications and case histories 2.7.1 Exploration of salt domes
32 33 33
35 35 37 42 42 42 43 46 48 52
53 53 54 55 57 61 65
68 70 70 71 72 74 79
82 84
90 92 92
Chapter 3 Geomagnetic methods 3.1 3.2
Introduction Basic concepts and units of geomagnetism 3.2.1 3.2.2 3.2.3 3.2.4 3.2.5
3.3
Flux den~ity. field strength and permeability Susceptibility Intensity of magnetisation Induced and remanent magnetisation Diamagnetism, paramagnetism and ferromagnetism
3.7
3.8
121 122 122
126
3.3.1 3.3.2
126
3.4.1 3.4.2
3.6
120
Magnetic properties of rocks Susceptihility of rocks and minerals Remanent magnetisation and K6'nigsherger ratios
3.4 The earth's magnetic field
3.5
117 118 118
Components o/the Earth's magnetic field Time variable field
129
131 131 137
Magnetic instruments
139
3.5.1 3.5.2 3.5.3 3.5.4 3.5.5
139 140 142 147
Torsion and balance magnetometers Fluxgate magnetometers Resonance magnetometers Cryogenic (SQU ID) magnetometers Gradiometers
Magnetic surveying
148 149
3.6.1 3.6.2 3.6.3
149 151 156
Field survey procedures Noise and corrections Data reduction
Qualitative interpretation
158
3.7.1 3.7.2
162 165
Profiles Pattern analysis on aeromagnetic maps
Quantitative interpretation
167
3.8.1 3.8.2
167 177
Anomalies due to different geometric/orms Simple depth determinations
Section 2 APPLIED SEISMOLOGY
Chapter 4 Applied Seismology: introduction and principles 4.1 Introduction 4.2 Seismic waves 4.2.1 Stress and strain 4.2.2 Types of seismic waves 4.2.3 Seismic wave velocities 4.3 Raypath geometry in layered ground 4.3.1 Reflection and transmission of normally incident
212 215 215 215 220 224
rays 4.3.2 Reflection and refraction of obliquely incident rays 4.3.3 Critical refraction 4.3.4 Diffractions 4.4 Loss of seismic energy 4.4.1 Spherical divergence or geometrical spreading 4.4.2 Intrinsic attenuation 4.4.3 Scattering 4.5 Seismic Energy Sources 4.5.1 Impact devices 4.5.2 Impulsive sources 4.5.3 Explosive sources 4.5.4 N on-explosive sources 4.5.5 High-resolution water-borne sources 4.5.6 Vibrators 4.6 Detection and recording of seismic waves 4.6.1 Geophones and accelerometers 4.6.2 Hydrophones and streamers 4.6.3 Seismographs
224 228 230 231 234 234 234 236 238 239 242 243 245 252 254 264 264 269 273
212
An introduction to applied and environmental geophysics
4.1
INTRODUCTION
The basic principle of exploration seismology is for a signal to be generated at a time that is known exactly and for the resulting seismic waves to travel through the sub-surface media and be reflected and refracted back to the surface where the returning signals are detected. The elapsed time between the source being triggered and the arrival of the various waves is then used to determine the nature of the sub-surface layers. Sophisticated recording and subsequent data processing enable detailed analyses of the seismic waveforms to be undertaken. The derived information is used to develop images of the sub-surface structure and a knowledge of the physical properties of the materials present. Exploration seismic methods were developed out of pioneering earthquake studies in the mid-to-late nineteenth century. The first use of an artificial energy source in a seismic experiment was in 1846 by Robert Mallet, an Irish physicist, who was also the first to use the word 'seismology'. John Milne introduced the drop weight as an energy source in 1885. His ideas were further developed by August Schmidt who, in 1888, devised travel time-distance graphs for the determination of seismic velocities. In 1899, G.K. Knott explained the propagation, refraction and reflection of seismic waves at discontinuity boundaries. In 1910, Andrija Mohorovicic identified distinct phases of P and S waves on travel-time plots derived from earthquake data. He attributed them to refractions along a boundary separating material with a lower velocity above and a higher velocity at greater depth. This boundary, which separates the Earth's crust from the lower-lying mantle, is now called the 'Moho', Significant developments in the refraction method were made during the First World War by both the Allies and Germany, particularly by Ludger Mintrop. Research was undertaken to develop methods by which the location of heavy artillery could be achieved by studying the waves generated by the recoil of the guns on firing. This work was developed further by Mintrop who obtained the first patent for a portable seismograph in 1919 (Keppner 1991). On 4 April 1921, Mintrop founded the company Seismos Gesellschaft in order to carry out seismic refraction surveys in the search for salt domes acting as trap structures for hydrocarbons. In 1924, the Orchard Salt Dome in Texas, USA, was discovered using seismic refraction experiments undertaken by Seismos on behalf of Gulf Production Co., thus demonstrating the effectiveness of the method as an exploration tool. The first seismic reflection survey was carried out by K.C. Karcher between 1919 and 1921 in Oklahoma, USA, based on pioneering work by Reginald Fessenden around 1913. By 1927, the seismic reflection method was being used routinely in exploration for hydro-
Applied seismology
carbons and within 10 years had become the dominant method world-wide in the exploration for oil and gas. The use of fan shooting was also finding favour in the early 1920s due to the encouragement by L.P. Garrett who was head of seismic exploration at Gulf. Parallel to these developments, research work was also being undertaken at the US Bureau of Standards. In 1928, O. von Schmidt, from Germany, derived a method of analysis of refraction data for dipping two-layer structures to obtain the angle of dip and true velocity within the lower layer. In 1931, he published a solution to solve the dipping three-layer case. The so-called Schmidt method is still commonly used to determine weathered layer corrections in seismic reflection surveying. In 1938, T. Hagiwara produced a method whereby, in addition to determining the lower layer velocity, the depths to this horizon could be determined at all shot and receiver positions along a single profile. Details of contributions made by Japanese engineering seismologists have been given by Masuda (1981). As withjust about all geophysical methods, the Second World War provided advances in technology that increased the usefulness of the various seismic methods. In 1959, J.G. Hagedoorn published his 'Plus-Minus' method (see Section 5.4.2). In 1960, Carl Savit demonstrated that it was possible to identify gaseous hydrocarbons directly using seismic methods by identifying 'bright spots'. In 1961, L.V. Hawkins introduced the 'reciprocal method' of seismic refraction processing that has been subsequently and substantially developed by D. Palmer (1980, 1991) as the 'generalised reciprocal method' (GRM; see Section 5.4.3). Both Hagedoorn's and Palmer's methods are similar to Hagiwara's. A very good review of the seismic refraction method has also been given by SJogren (1984). Major developments in the seismic methods have come about by revolutions within the computing industry. Processing once thought possible only by mainframe computers is now being handled on personal computers and stand-alone workstations. With the vast increase in computer power, currently at a rate of an order of magnitude every two years, has come the ability to process data far more quickly and reliably, and this has opened up opportunities for seismic modelling. Obviously, with the degree of sophistication and specialisation that now exists in the seismic industry, it is not possible to provide anything like a comprehensive account here. There are many books available which deal extensively with exploration seismology, such as those by Claerbout (1976, 1985), McQuillin et al. (1984), Hatton et al. (1986), Waters (1987), Yilmaz (1987), and Dobrin and Savit (1988), among others. There are two main seismic methods - refraction and reflection.
Since the 1980s there has been a major shift towards using highresolution seismic reflection surveying in shallow investigations (i.e.
213
214
An introduction to applied and environmental geophysics
to depths less than 200 m and especially less than 50 m). Previously, of the two seismic methods, refraction had been used principally within engineering site investigations. Neither seismic sources with suitably high frequencies, nor the data processing capability, were available or cost-effective for small-scale surveys. This is no longer so, and shallow seismic investigations are now much more common both on land and over water. Data obtained by signal-enhancement seismographs can be processed in similar ways to data acquired in large-scale hydrocarbon exploration surveys. Consequently, following a brief overview of the basic principles of applied seismology in this chapter,
Table 4.1
Derived information and applications of exploration seismology
Gross geological features:
Depth to bedrock Location of faults and fracture zones Fault displacement Location and character of buried valleys Lithological determinations Stratigraphy Location of basic igneous dykes Petrophyscial information:
Elastic moduli Density Attenuation Porosity Elastic wave velocities Anisotropy Rippability Applications:
Engineering site investigations Rock competence Sand and gravel resources Detection of cavities Seabed integrity (for siting drilling rigs) Degassing or dewatering of submarine sediments Preconstruction site suitability for: new landfill sites major buildings marinas and piers sewage outfall pipes tunnel construction etc. Hydrogeology and groundwater exploration Ground particle velocities Forensic applications: location of crashed aircraft on land design of aircraft superstructures monitoring Nuclear Test Ban Treaty location of large bore military weapons
Applied seismology
seismic refraction data processing and interpretation techniques are discussed in the next chapter, with seismic reflection surveying being discussed in detail in Chapter 6. These will provide a brief introduction to the shallow refraction and reflection methods (to which emphasis is given), and briefly to the processes used in the seismic industry for hydrocarbon exploration. In addition to hydrocarbon exploration, seismic methods have a considerable number of other applications (Table 4.1), ranging from crude depth-to-bedrock determinations through to more subtle but fundamental information about the physical properties of sub-surface media, and from the obvious applications such as site suitability through to the apparently obscure uses such as in forensic investigations in aircraft crashes on land, such as the Lockerbie air disaster in Scotland in 1989. Details of some of these applications are given in Section 6.6.
4.2 SEISMIC WAVES 4.2.1
Stress and strain
When an external force F is applied across an area A of a surface of a body, forces inside the body are established in proportion to the external force. The ratio of the force to area (F/ A) is known as stress. Stress can be resolved into two components, one at right-angles to the surface (normal or dilatational stress) and one in the plane of the surface (shear stress). The stressed body undergoes strain, which is the amount of deformation expressed as the ratio of the change in length (or volume) to the original length (or volume). According to Hooke's Law, stress and strain are linearly dependent and the body behaves elastically until the yield point is reached. Below the yield point, on relaxation of stress, the body reverts to its pre-stressed shape and size. At stresses beyond the yield point, the body behaves in a plastic or ductile manner and permanent damage results. If further stress is applied, the body is strained until it fractures. Earthquakes occur when rocks are strained until fracture, when stress is then released. However, in exploration seismology, the amounts of stress and strain away from the immediate vicinity of a seismic source are minuscule and lie well within the elastic behaviour of natural materials. The stress/strain relationship for any material is defined by various elastic moduli, as outlined in Figure 4.1 and Box 4.1. 4.2.2 Types of seismic waves
Seismic waves, which consist of tiny packets of elastic strain energy, travel away from any seismic source at speeds determined by the
215
Chapter 5 Seismic refraction surveying 5.1 5.2
Introduction General principles of refraction surveying 5.2.1 5.2.2
5.3
Geometry of refracted raypaths 5.3.1 5.3.2
5.4
Phantoming H agedoorn plus-minus method Generalised reciprocal method (GRM) Hidden-layer problem Effects of continuous velocity change
Applications and case histories 5.5.1 5.5.2 5.5.3 5.5.4
5.1
Planar interfaces Irregular (non-planar) interfaces
Interpretational methods 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5
5.5
Critical refraction Field survey arrangements
Rockhead determination for a proposed waste disposal site Location of a buried do line Assessment of rock quality Landfill investigations
276 277 277 280 281 282 291 291 292 295 300 303 303 305 305 308 311 316
INTRODUCTION
Seismic refraction experiments can be undertaken at three distinct scales: global (using earthquake waves), crustal (using explosion seismology), and near-surface (engineering applications). For the purposes of this book, emphasis is placed on shallow investigations. Discussion of passive seismic refraction in earthquake studies can be found in other texts, such as those by Brown and Mussett (1981), Gubbins (1990) and Kearey and Vine (1990). The major strength of the seismic refraction method is that it can be used to resolve lateral changes in the depth to the top of a refractor
320
An introduction to applied and environmental geophysics
seismic measurements were made to determine the shear wave velocity (Vs ). Their results showed excellent correlation between Vs and the geotechnical properties of the tailings material. An integral part of the successful management of an enclosed landfill is the maintenance of the integrity of the compacted clay cap overlying the waste material. As long as this impermeable layer remains intact, gases are kept beneath (to vent in a controlled manner through appropriate outlets) and rain water/snow melt is kept out to run off into surface drains. However, erosion can occur into this clay cap and it can also degrade through differential settlement of the waste beneath. Carpenter et al. (1991) reported on their use of both seismic refraction and electrical resistivity surveys to examine the integrity of a clay cap over a municipal landfill at Mallard North, near Chicago, USA. They demonstrated that detailed mapping of P-wave velocities could be used to identify areas where the clay cap had been fractured (giving rise to low P-wave velocities) compared with the intact clay cap (with higher P-wave velocities). Similarly, variability in electrical resistivity with azimuth around a central point indicated the orientation of fractures within the clay cap. Maps of the site and of their survey locations are shown in Figure 5.30. Carpenter and co-workers found that average P-wave velocities determined along survey lines parallel and perpendicular to fractures were around 370 ± 20 mls and 365 + 10 mis, respectively, compared with a value of 740 ± 140m/s over unfractured clay cap. They also reported difficulty in obtaining refracted arrivals in some areas owing to the P-wave velocity in the underlying waste being lower than that for the clay cover. It is thought that where clay caps are of the order of 1.5-2 m thick, as in this case, electrical resistivity sub-surface imaging could provide a quick and reliable method of measuring the thickness non-intrusively.
Chapter 6 Seismic reflection surveying 6.1 Introduction 6.2 Reflection surveys 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6
6.3
General considerations General reflection principles Two-dimensional survey methods Three-dimensional surveys Vertical Seismic Profiling (VSP) Cross-hole seismology: tomographic imaging
Reflection data processing
343 344 347 352
Pre-processing Static corrections (field statics) Convolution and deconvolution Dynamic corrections, velocity analyses and stacking Filtering Migration
6.4 Correlating seismic data with borehole logs and cones 6.4.1 6.4.2
6.6
323 323 326 331 338 342
6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6
6.5
322 323
Sonic and density logs and synthetic seismograms Correlation with Dutch cones
355 363 367
373 374 375
Interpretation
380
6.5.1 6.5.2 6.5.3
380 382 387
Vertical and horizontal resolution I dentification of primary and secondary events Potential interpretational pi~ralls
Applications
390
6.6.1 6.6.2 6.6.3
390 397
6.6.4
High-resolution seismic profiling on land High-resolution seismic profiling over water Geophysical diffraction tomography in seismic palaeontology Forensic seismology
408 412
Section 3 ELECTRICAL METHODS
Chapter 7 Electrical resistivity methods 7.1 Introduction 7.2 Basic principles 7.2.1 True resistivity 7.2.2 Current flow in a homogeneous earth 7.3 Electrode configurations and geometric factors 7.3.1 General case 7.3.2 Electrode cmifigurations 7.3.3 Media with contrasting resistivities 7.4 Modes of development 7.4.1 Vertical electrical sounding (VES) 7.4.2 Automated array scanning 7.4.3 Constant-separation traversing (CST) 7.4.4 Field problems 7.5 Interpretation methods 7.5.1 Qualitative approach 7.5.2 Master curves 7.5.3 Curve matching by computer 7.5.4 Equivalence and suppression 7.5.5 Inversion, deconvolution and numerical modelling
7.6 Mise-a-la-masse method 7.7 Applications and case histories 7.7.1 Engineering site investigations 7.7.2 Groundwater and landfill surveys 7.7.3 Glaciological applications 7.8 Electrokinetic (EK) surveying in groundwater surveys
7.9 Leak detection through artificial membranes
418 418 418 424 426 426 427 433 441 441 444 446 447 453 453 455 457 461 464 467 470 470 475 482 485 488
418
An introduction to applied and environmental geophysics
7.1
INTRODUCTION
Electrical resistivity methods were developed in the early 1900s but have become very much more widely used since the 1970s, due primarily to the availability of computers to process and analyse the data. These techniques are used extensively in the search for suitable groundwater sources and also to monitor types of groundwater pollution; in engineering surveys to locate sub-surface cavities, faults and fissures, permafrost, mineshafts, etc.; and in archaeology for mapping out the areal extent of remnants of buried foundations of ancient buildings, amongst many other applications. Electrical resistivity methods are also used extensively in downhole logging. For the purposes of this chapter, applications will be confined to the use of direct current (or very-low-frequency alternating current) methods. Electrical resistivity is a fundamental and diagnostic physical property that can be determined by a wide variety of techniques, including electromagnetic induction. These methods will be discussed in their respective chapters. That there are alternative techniques for the determination of the same property is extremely useful as some methods are more directly applicable or more practicable in some circumstances than others. Furthermore, the approaches used to determine electrical resistivity may be quite distinct - for example, ground contact methods compared with airborne induction techniques. Mutually consistent but independent interpretations give the interpreter greater confidence that the derived model is a good approximation of the sub-surface. If conflicting interpretations result, then it is necessary to go back and check each and every stage of the data acquisition, processing and interpretation in order to locate the problem. After all, the same ground with the same physical properties should give rise to the same model irrespective of which method is used to obtain it.
7.2 BASIC PRINCIPLES 7.2.1
True resistivity
Consider an electrically uniform cube of side lenght L through which a current (1) is passing (Figure 7.1). The material within the cube resists the conduction of electricity through it, resulting in a potential drop (V) between opposite faces. The resistance (R) is proportional to the length (L) of the resistive material and inversely proportional to the cross-sectional area (A) (Box 7.1); the constant of proportionality is the 'true' resistivity (symbol: p). According to Ohm's Law (Box 7.1) the ratio of the potential drop to the applied current (VII) also defines the resistance (R) of the cube and these two expressions can be combined (Box 7.2) to form the product of a resistance (0) and
Electrical resistivity methods
419
~--0---
I I
-~ L
(A)
"
144- - -
I
"
"" ""
p
L ---.~I
a distance (area/length; metres); hence the units of resistivity are ohm-metres (Qm). The inverse of resistivity (l/p) is conductivity (0-) which has units of siemens/metre (S/m) which are equivalent to mhos/metre (Q-l m- 1). It should be noted that Ohm's Law applies in the vast majority of geophysical cases unless high current densities (1) occur, in which case the linearity of the law may break down. If two media are present within the resistive cube, each with its own resistivity (PI and P2)' then both,proportion of each medium and , . their geometric form within the cube (Figure 7.2}becorrte important j considerations. The formerly isotropic cube will now exhibit variations in electrical properties with the direction of measurement (known as anisotropy); a platey structure results in a marked anisotropy, for example. A lower resistivity is usually obtained when measured parallel to limitations in phyllitic shales and slates.compared with that at right-angles to the laminations. The presence and c-'orientation of elongate brine pockets (with high conductivity) strongly influence the resistivity of sea ice (Timco 1979). The amount of anisotropy is described by the anisotropy coefficient, which is the ratio of maximum to minimum resistivity and which generally lies in the range 1-2. Thus it is important to have some idea of the form of electrical conductors with a rock unit. Detailed discussions of anisotropy have been given, for example, by Maillet (1947), Grant and West (1965) and Telford et al. (1990) (see also Section 7.3.3).
(8)
Figure 7.1 (A) Basic definition of resistivity across a homogeneous block of side length L with an applied current I and potential drop between opposite faces of V. (B) The electrical circuit equivalent, where R is a resistor
420
An introduction to applied and environmental geophysics
Box 7.1
True resistivity (see Figure 7.1)
Resistance (R) is proportional to length (L) divided by area (A): R ocL/A.
This can be written as R = pL/A, where p is the true resistivity. Ohm's Law For an electrical circuit, Ohm's Law gives R = VII, where V and I are the potential difference across a resistor and the current passing through it, respectively. This can be written alternatively in terms of the electric field strength (E; volts/m) and current density (J; amps/m Z) as: p=E/J(Qm)
Box 7.2
Resistivity VA
p
=Ii (Q/m)
There are three ways in which electric current can be conducted through a rock: electrolytic, electronic (ohmic) and dielectric conduction. Electrolytic conduction occurs by the relatively slow movement of ions within an electrolyte and depends upon the type of ion, ionic concentration and mobility, etc. Electronic conduction is the process by which metals, for example, allow electrons to move rapidly, so carrying the charge. Dielectric conduction occurs in very weakly conducting materials (or insulators) when an external alternating current is applied, so causing atomic electrons to be shifted slightly with respect to their nuclie. In most rocks, conduction is by way of
Figure 7.2 Three extreme structures involving two materials with true resistivities Pi and Pz' After Grant and West (1965), by permission
z
I --y
(A)
(B)
(C)
•
Electrical resistivity methods
I
"
pore fluids acting as electrolytes with the actual mineral grains contributing very little to the overall conductivity of the rock (except where those grains are themselves good electronic conductors). At the frequencies used in electrical resistivity surveying dielectric conduction can be disregarded. However, it does become important in 'spectral induced polarisation' and in 'complex resistivity' measurements (see Chapter 9). The resistivity of geological materials exhibits one of the largest ranges of all physical properties, from 1.6 x 10- 80m for native silver to 10 16 Om for pure sulphur. Igneous rocks tend to have the highest resistivities; sedimentary rocks tend to be most conductive, largely due to their high pore fluid content; and metamorphic rocks have intermediate but overlapping resistivities. The age of a rock also is an important consideration: a Quaternary volcanic rock may have a resistivity in the range 10-200 Om while that of an equivalent rock but Precambrian in age may be an order of magnitude greater. This is a consequence of the older rock having far longer to be exposed to secondary infilling of interstices by mineralisation, compaction decreasing the porosity and permeability, etc. In sedimentary rocks, the resistivity of the interstitial fluid is probably more important than that of the host rock. Indeed, Archie (1942) developed an empirical formula (Box 7.3) for the effective resistivity of a rock formation which takes into account the porosity (cf», the fraction (s) of the pores containing water, and the resistivity of the water (Pw)' Archie's Law is used predominantly in borehole logging. Korvin (1982) has proposed a theoretical basis to account for Archie's Law. Saline groundwater may have a resistivity as low as 0.050m and some groundwater and glacial meltwater can have resistivities in excess of 10000 m. Resistivities ofsome common minerals and rocks are listed in Table 7.1, while more extensive lists have been given by Telford et ai. (1990). Box 7.3
Archie's Law p
I
1
= acf> -ms-n Pw
where p and Pw are the effective rock resistivity, and the resistivity of the pore water, respectively; cf> is the porosity; s is the volume fraction of pores with water; a, m and n are constants where 0.5 ~ a ~ 2.5, 1.3 ~ m ~ 2.5, and n;::::; 2. The ratio pi Pw is known as the Formation Factor (F). Some minerals such as pyrite, galena and magnetite are commonly poor conductors in massive form yet their individual crystals have high conductivities. Hematite and sphalerite, when pure, are virtual insulators, but when combined with impurities they can become very
j j
421
422
An introduction to applied and environmental geophysics
Table 7.1
Resistivities of common geologic materials
Material
Nominal resistivity (Om)
Sulphides: Chalcopyrite Pyrite Pyrrhotite Galena Sphalerite
1.2 x 10 - 5 - 3 x 10 - 1 2.9 x 10 - 5 -1.5 7.5 x 10- 6 -5 x 10- 2 3 x 10- 5 -3 X 10 2 1.5 X 10 7
Oxides: Hematite Limonite Magnetite Ilmenite
3.5 x 10- 3_10 7 10 3 _10 7 5 x 10- 5 -5.7 X 10 3 10- 3 -5 x 10
Quartz Rock salt Anthracite Lignite Granite Granite (weathered) Syenite Diorite Gabbro Basalt Schists (calcareous and mica) Schist (graphite) Slates Marble Consolidated shales . Conglomerates Sandstones Limestones Dolomite Marls Clays Alluvium and sand Moraine Sherwood sandstone Soil (40% clay) Soil (20% clay) Top soil London clay Lias clay Boulder clay Clay (very dry) Mercia mudstone Coal measures clay Middle coal measures Chalk Coke Gravel (dry) Gravel (saturated) Quaternary/Recent sands
3 X 102 -10 6 3xlO-10 13 10- 3 -2 X 10 5 9-2 X 10 2
3 X 102_ X 106 3 x 10-5 X 102 10 2 _10 6 104 _10 5 10 3 _10 6 10-1.3 X 10 7 20-104 10-102 6 x 102 -4 X 10 7 102 -2.5 X 10 8 20-2 X 10 3 2 X 10 3 -10 4 1-7.4 X 108 5 X 10-10 7 3.5 x 102 -5 x 10 3 3-7 x 10 1-10 2 10-8 X 102 10-5 X 10 3 100-400 8 33 250-1700 4-20 10-15 15-35 50-150 20-60 50 >100 50-150 0.2-8 1400 100 50-100
.. Electrical resistivity methods
Table 7.1 (continued) Material
Nominal resistivity (11 m)
Ash Colliery spoil Pulverised fuel ash Laterite Lateritic soil Dry sandy soil Sand clay/clayey sand Sand and gravel Unsaturated landfill Saturated landfill Acid peat waters Acid mine waters Rainfall runoff Landfill runoff
4
Glacier ice (temperate) Glacier ice (polar) Permafrost
10-20 50-100 800-1500 120-750 80-1050 30-215 30-225 30-100 15-30 100 20 20-100 104
* - 10°C to - 60°C, respectively; strongly temperature-dependent. Based on Telford et al. (1990) with additional data from McGinnis and Jensen (1971). Reynolds (1987a). Reynolds and Paren (1980,1984) and many commercial projects.
good conductors (with resistIvItIes as low as 0.1 Qm). Graphite dispersed throughout a rock mass may reduce the overall resistivity of otherwise poorly conducting minerals. For rocks that have variable composition, such as sedimentary rocks with gradational facies, the resistivity will reflect the varying proportions of the constituent materials. For example, in northern Nigeria it is possible, on the basis of the interpreted resistivities, to gauge whether a near-surface material is a clayey sand or a sandy clay. Resistivities for sandy material are about 100 Q m and decrease with increasing clay content to about 40Qm, around which point clay becomes the dominant constituent and the values decrease further to those more typical of clay: wellformed and almost sand-free clay has a value in the range 1-10 Q m (Reynolds 1987a). The objective of most mordern electrical resistivity surveys is to obtain true resistivity models for the sub-surface because it is these that have geological meaning. The methods by which field data are obtained, processed and interpreted will be discussed later. The apparent resistivity is the value obtained as the product of a measured resistance (R) and a geometric factor (K) for a given electrode array (see Section 7.3.2), according to the expression in Box 7.2. The geometric factor takes into account the geometric spread of electrodes and contributes a term that has the unit of length (metres). Apparent resistivity (Pa) thus has units of ohm-metres.
423
424
7.2.2
An introduction to applied and environmental geophysics
Current flow in a homogeneous earth
For a single current electrode implanted at the surface of a homogeneous medium of resistivity p, current flows away radially (Figure 7.3). The voltage drop between any two points on the surface can be described by the potential gradient (- c5 VI c5x), which is negative because the potential decreases in the direction of current flow. Lines ofequal voltage ('equipotentials') intersect the lines of equal current at right-angles. The current density (J) is the current (I) divided by the area over which the current is distributed (a hemisphere; 2nr 2 ), and so the current density decreases with increasing distance from the current source. It is possible to calculate the voltage at a distance (r) from a single current point source (Box 7.4). If, however, a current sink is added, a new potential distribution occurs (Figure 7.4) and a modified expression is obtained to describe the voltage at any point (Box 7.5).
Figure 7.3 (A) Three-dimensional representation of a hemispherical equipotential shell around a point electrode on a semi-infinite, homogeneous medium. (B) Potential decay away from the point electrode
-+..
(A)
---~T----:;:::::,JIil::------H+"r
Current flow line
Equipotential surface
z
v
-====:::=------~L----.:.~--=======__+r r o
Electrical resistivity methods
Box 7.4
425
(See Figure 7.3)
The potential difference (b V) across a hemispherical shell of incremental thickness br is given by: bV br =
I - p. J = - p 2n:r2 .
Thus the voltage Vr at a point r from the current point source is: Vr =
f bV =
-
f
I
pI 1
p 2n:r 2 br = 2n: . ~ .
Figure 7.4 Current and equipotentiallincs produced by a current source and sink. From van Nostrand and Cook (1966), by permission
1----1
Figure 7.5 Generalised form of electrode configuration in resistivity surveys V
+/
A
C,
I. I I 1" I
M P,
AM
.. I.. I
AN
-/
N P2
~I C2
MB I I
"j"
B
NB
I I
~I I
426
An introduction to applied and environmental geophysics
Box 7.5 (See Figure 7.5) For a current source and sink, the potential Vp at any point P in the ground is equal to the sum of the voltages from the two electrodes, such that: v;, = lj, + Va where lj, and Va are the potential contributions from the two electrodes, A( + I) and B( - I). The potentials at electrode M and N are:
However, it is far easier to measure the potential difference, (iVMN , which can be rewritten as: (i VMN
= VM -
VN
= ~~ {[ A~ -
~ B] - [ A~ - ~B J}
Rearranging this so that resistivity P is the subject:
p=2n(i:MN{[A~_ ~BJ-[A~- ~BJrl 7.3 ELECTRODE CONFIGURATIONS AND GEOMETRIC FACTORS 7.3.1
General case
The final expression in Box 7.5 has two parts, namely a resistance term (R; units 0) and a term that describes the geometry of the electrode configuration being used (Box 7.6) and which is known as the geometric factor (K; units m). In reality, the sub-surface ground does not conform to a homogeneous medium and thus the resistivity obtained is no longer the 'true' resistivity but the apparent resistivity (Pa) which can even be negative. It is very important to remember that the apparent resistivity is not a physical property of the sub-surface Box 7.6. The geometric factor (see Figure 7.5) The geometric factor (K) is defined by the expression:
K=2n[A~- ~B- A~+ ~BTl Where the ground is not uniform, the resistivity so calculated is called the apparent resistivity (Pa): Pa = RK, where R = bV/I.
•
Electrical resistivity methods 1.0
t~'"
0.8
~
E g' 0.6
.~
= E ~
::J
0.4
o
'0
~
&.
0.2
e
Q.
o L---'--.L---...L...--......L..--.....L..----'---ABlz o 2 4 6 8 10
I
1
media, unlike the true resistivity. Consequently, all field resistivity data are apparent resistivity while those obtained by interpretation techniques are 'true' resistivities. Figure 7.6 shows that, in order for at least 50 % of the current to flow through an interface at a depth of z metres into a second medium, the current electrode separation needs to be at least twice - and preferably more than three times-the depth. This has obvious practical implications, particularly when dealing with situations where the depths are of the order of several hundreds of metres, so requiring very long cable lengths that can produce undesirable inductive coupling effects. For very deep soundings where the electrode separation is more than several kilometres, telemetering the data becomes the only practical solution (e.g. Shabtaie et al. 1980, 1982). However, it should be. emphasised that it is misleading to \ equate the depth of penetrationwith the current electrode separation as a general rule of thumb in the region of a resistivity survey. This aspect is discussed in Section 7.3.3. " 7.3.2
Electrode configurations
The value of the apparent resistivity depends on the geometry of the electrode array used, as defined by the geometric factor K. There are three main types of electrode configuration, two of which are named after their originators - Frank Wenner (1912a,b) and Conrad Schlumberger-and a range of sub-types (Table 7.2 and Figure 7.7). The geometric factors for these arrays are given in Box 7.7 and a worked example for the Wenner array is given in Box 7.8. Arrays highlighted in bold in Table 7.2 are those most commonly used.
427
Figure 7.6 Proportion of current flowing below a depth z (m); AB is the current electrode ~alf-separation
428
An introduction to applied and environmental geophysics
Table 7.2
Electrode configurations (see also Figure 7.7)
Wenner arrays
Standard Wenner Offset Wenner Lee-partitioning array Tripotential (ex, fJ and y arrays)
Schlumberger array
Standard Schlumberger Brant array Gradient array
Dipole~dipole arrays
Normal (axial or polar) Azimuthal Radial Parallel Perpendicular Pole~Dipole
Equatorial Square (special form of equatorial)
Figure 7.7 Electrode configurations used in electrical surveys
C,. -- -- -a - - - - +P,. - -- - -a - - - - + P2 •
•
Wenner
Schlumberger
X.
- - --
•
~
•
.-b-" ------------+
C,.--a--.C2 . - - - - - - - - - - - na -----------.-P,.-- a--+P2 • • X • •
c, • - -- --- - - a----- ---. C2
... I I I I I
I I
Square
-a- -- - .C2
P, ~ • .X •
C, • .------------ a
Dipoledipole
•
. I
a
X
I I I I I I I
... P,
P2
(n=3)
Electrical resistivity methods
Dipole-dipole arrays have been used extensively by Russian geophysicists since 1950, and especially in Canada, particularly for 'induced polarisation' surveys (see Chapter 9) in mineral exploration, and in the USA in groundwater surveys (Zohdy 1974). The term 'dipole' is misapplied in a strict sense because the interelectrode\senarationJor each of the current or potential electrode pairs should be insignificant with respect to the length of the array, which it is not. However, the term is well established in its usage. Box 7.7 Apparent resistivities for given geometric factors for electrode configurations in Figure 7.7
I
,
Wenner array:
Pa = 2naR P a = 3naR
Two-electrode:
P a = 2nsR
Lee array:
Pa = 4naR
(alpha/beta arrays) (gamma rays)
n:T ::2]
Schlumberger array:
Pa =
1-
R;
a ~ 5b
L2 1 P =2n--R
Gradient array:
a
a
I-X where G = (y2 + (1 _ X)2)3/2
G
I+X + (y2 + (1 + X)2)3/2
andX=x/L, Y=y/L Dipole-dipole array:
Pa = nn(n + l)(n
Pole-dipole array:
Pa = 2nn(n + 1 )aR
Square array:
Pa
=
na(2 +
+ 2)aR
J2) R
These different types and styles of electrode configuration have particular advantages, disadvantages and sensitivities. Factors affecting the choice of array type include the amount of space available to layout an array and the labour-intensity of each method. Other important considerations are the sensitivity to lateral inhomogeneities (Habberjam and Watkins 1967a; Barker 1981) and to 'dipping interfaces (Broadbent and Habberjam 1971). ' A graphic example of the different responses by the three main electrode configurations is given by so-called '~Jgnal contribution sections' (Barker 1979) shown in Figure 7.8. These sections are contoured"plots of the contribution made by each unifvolume of the y.:,\ . sub-surface to the voltage.E:1_e!isu~~c:i_ atthe surface, !
tV
r);J
.
\,)'
\j
l)
\
,
.'
.
>
.,
~y;.
. .
.,J
429
430
An introduction to applied and environmental geophysics
-----------L-----------
(6)
c,
c.
./
..'
. \
(C)
Box 7.8
Worked example of how to calculate a geometric factor
Using the expression previously defined in Box 7.6 (see also Figure 7.5), and substituting in the correct values for the Wenner array:
K=2n[~-~-~+~J-l =2n[~_2J-l a 2a 2a a a 2a =2na. Hence, as Pa = KR, Pa = 2naR.
Figure 7.8 Signal contribution sections for: (A) Wenner, (B) Schlumberger and (C) dipole-dipole configurations. Contours indicate the relative contributions made by discrete volume elements of the sub-surface to the total potential difference measured between the two potential electrodes PI and P 2' From Barker (1979), by permission
Electrical resistivity methods
Figure 7.8A shows the signal contribution for a Wenner array. In the near-surface region, the positive and negative areas cancel each other out and the main response, which originates from depth, is largely flat (see the 1 unit contour). This indicates that for horizontally, layerecrInedia, the Wenner array has a high vertical resolution. The Schlumberger array has almost as high a vertical resolution, but note that the form of the signal contribution at depth is now concave upwards (Figure 7.8B). For the dipole-dipole array (Figure 7.8C), the lobate form of the signal contribution indicates that there is a poor vertical resolution and that the array is particularly sensitive to deep lateral resistivity variations, making it an unsuitable array for depth sounding (Bhattacharya and Patra 1968). Nevertheless, this sensitivity can be utilised in resistivity profiling (see Section 7.4.3). A modified electrode array (Lee partitioning array) was devised by Lee (Lee and Schwartz 1930) in an attempt to reduce the undesirable effects of near-surface lateral inhomogeneities. An alternative tripotential method was proposed by Carpenter (1955) and by Carpenter and Habberjam (1956) which combined the apparent resistivities obtained for the alpha, beta and gamma rays (Figure 7.9). The
Figure 7.9 Wenner tripotential electrode configurations for N = 2. x is the fixed interelectrode separation, and the active electrode separation is 2x, From Ackworth and Griffiths (1985), by permission
ALPHA
• 10
P,
,
'2
1
t
C,
(0
t
PI I
I,
']
t
(3
'6
5
'1
8
I
-
I
-
C2
BETA
t '0
(0 I
+
,
'2
,P,
6)
f
I
J
f
C1
C,
,
P2 I
s
')
8
,)
8'
GAMMA
, I '
0
I
,
0~ I
I
a N .2 a • 2x
J
"
t
C,
•
+
"
a I
x
•
C2
_--0
I
I
2x
3x
•
..
I I.x
P2
's
6
t
6) 0
I 5x
.. I 6x
431
-
-
432
An introduction to applied and environmental geophysics
C•
•
OFFSET P =999
C,
a
\
method has been discussed further by Ackworth and Giffiths (1985). A smoothing technique using the tripotential method was produced by Habberjam and Watkins (1967a). An alternative technique, called the Qilset Wenner method (Barker 1981), has been readily adopted for its ease of use. The method is extremely simple in concept. Figure 7.10 shows a single contribution section for a standard Wenner array. A conducting sphere buried in a semi-infinite homogeneous medium with true resistivity of 100 Q m is located in a positive region of-the signal contribution section (Figure 7.10A). The corresponding apparent resistivity, calculated using an exact analytical method (Singh 1976), is 91.86 Q m. Offsetting the Wenner array one spacing to the right (Figure 7.10B), the previously positive areas are now negative and vice versa, and the buried sphere is located in a negative region resulting in an apparent resistivity of 107.81 Qm. The average of these two apparent resistivities is 99.88 Q m, thereby reducing the error due to a lateral inhomogeneity from around ± 8% to only 0.1 %. One array that is seldom used, but which has two major advantages, is the S Pt) but has a reduced strength kS, where k is dependent upon the resistivity contrast between the two media and lies in the range + 1. This k factor is akin to the reflection coefficient in optics and in reflection seismology, and has the form given in Box 7.11. If the current passes from a lower resistivity medium to one with a higher resistivity, k is positive; if it passes into a medium with a lower resistivity, k is negative. Box 7.10 (See Figure 7.12A) Refraction of current flow at a plane boundary: tan 8 2 /tan 8 t = pd P2'
436
An introduction to applied and environmental geophysics
Figure 7.12 (A) Refraction of current flow lines, and (B) Distortion of equipotential and current flow lines from a point electrode across a plane boundary between media with contrasting resistivities (Telford et al. 1990). (C) Method of optical images for the calculation of a potential at a point (see text for details)
(A)
Medium 2
Medium 1
(8) High-resistivity medium 2
Low-resistivity medium 1
~~~+~~.+- c' image
P2= 3p,
k=O.5
Current flow lines Undistorted current flow lines Line of equipotential
~;t::t":rT--t-
c' image
P2
p, High-resistivity medium 1
\
(C) C
Low-resistivity medium 2
Medium 1
Medium 2
P,
P2 C'image
p, =3P2 k=--o.5
Electrical resistivity methods
Box 7.11
Electrical reflection coefficient, k (see Figure 7.12C)
Potential at P:
Potential at Q: i..J
r
At the interface V = V' and r I = r 2 = r 3 . Hence: PI P2
t
* ,1
'3
1- k 1+k
or
In the case when the boundary is vertical, different types of anomaly will be produced dependent upon the electrode configuration used and whether it is developed at right-angles or parallel (broadside) to the boundary. Examples of the types of anomalies produced are illustrated in Figure 7.13. The cusps and discontinuity in (A), (B) and (C) are due to the positioning of the electrodes relative to the vertical boundary with each cusp occurring as one electrode crosses the boundary. In the case of the Wenner array, it can be explained in detail (Figures 7.13D and E) as follows. As the array is moved from the high-resistivity medium towards the low-resistivity medium (case (i) in Figure 7.13), the current flow lines converge towards the boundary, increasing the current density at the boundary but decreasing the potential gradient at the potential electrodes. The apparent resistivity gradually falls from its true value until a minimum is reached when the current electrode C z is at the boundary (ii). Once C 2 has crossed into the low-resistivity unit (iii), the current density increases adjacent to the boundary but within the Jow-resistivity medium, causing the potential gradient between the potential electrodes to rise. When the entire potential electrode dipole has crossed the boundary (iv), the current density is highest in the high-resistivity medium, causing the potential gradient across PI - P 2 to fall dramatically. With the current electrode C I now into the low-resistivity unit (v), the current adjacent to the boundary is divergent. This results in an elevated potential gradient between PI and P 2 which falls to a normal value when the entire collinear array is sufficiently far away from the boundary. At this point the current flow is radial once more. The magnitude of the cusps and discontinuities is
437
, 438
)
orr
.L
~
An introduction to applied and environmental geophysics
.1
P,
Wenner
• c,
P,
'\
C,
P,
,
I
,
I
P2 (8)
Figure 7.13 Apparent resistivity profiles measured over a vertical boundary using different electrode arrays: (A) Wenner (with its characteristic Wshaped anomaly), (B) Schlumberger, and (C) dipole-dipole. After Telford et al. (1990), by permission of Cambridge University Press. (D) Profile shapes as a function of resistivity contrast. From van Nostrand and Cook (1966), by permission. (E) Plan view of successive moves of a Wenner array with electrode positions indicated for six marked points in (D)
P.
(A)
P, c,
I
•
Schlumberger
P, Pz
I
...
•
I
(C)
p,
Dipole-dipole
t:--------~
c, c,
P, P,
f I
.~
[.
(~.
i':'
"
Figure 7.14' (op£.Q§ite) Apparent resistivity profiles·across a thin vertical dyke using (A) a dipole-dipole array eand (B) a Wenner array. (C) Computed normalised resistivity profiles across =' a thin vertical dyke with different resistivity contrasts. After van Nostrand ~ and Cook (1976), by permission (0)
~
1.0 0.9
-,,, ~~
d)
0.8 07
.(iii)
0.6
(ii)
pJpl 0.5 0.4 0.3
.,
0
l\ I" l\ I". l\ I......... \. 11M
0.1 ~
~
~
.
I'" 0.2 ~\ I""" 0.3
,\ "'-
0.2
,
0.5
-
O.§. 0.7
1\
01
......
...... .......
'"
(VI)
0.··
E 0
~
-
0.4
I 234
,
.!. P P, 1 C SurtlC8 'I ~ ..: ':~"' .. ,.: "'~:"':~.. x -"- iI , :"::- :"::p, :.:: 'Flu~ P2
[ .... : (E)
-4
~,
:......
:
-3
-2
-1
t, . ~
~,
.....
C, I
,
-----P2 < p,
O;-..._,1=--_;:2"--_;:3_--j~ xla
I
I
I
I
(i) . - - . - - - - - - . I (ii) . - - . _ . - - . (iii)
.• .--+__.--.
.--.~+-(iv)
(v) , - - . - . - - . I (vi) . - - . - - • .....-. I
Boundary
Electrical resistivity methods
(A)
4
P./P, Dipole-dipole station at midpoint of P,P,
3 2
c.c, I~ I..
~
P.p, II
__
~_I_~"_"".>--""._-4r
r
b
r_"'_4_
°Wenner station at midpoint ofC,P,
(8)
--..-. ~ -,"--..~. ~,\-.-/
a",2b
--b-
----------~r------------
V~
p,
pip, '" 5.67 k", 0.7
p,
P2
(C)
2.5
:
I
I
I
I
,
I
,
IA
Itt.
i i
,
2.0
~V I
pIp, "
~
1.5
,
.
I
. 1.0
-
-4
Jr--.... . ~ /.' . ;.. .. . . . ~
~ ..
-2
-3
." . -. . ... ..... . 0.4
\
\
..
••0.2••
.
..
.
,
.. ~ l".ooa'. .'\. . ... ... .'.'
-1
°a
2
~
....
3
x
Surlace
p,
P2 > p,
4
439
440
An introduction to applied and environmental geophysics
dependent upon the resistivity contrast between the two media. However, if the array is orientated parallel to the boundary such that all electrodes cross it simultaneously, the cusping is reduced. (Figure 7.13B, dashed line). The anomaly shape is similarly varied over a vertical dyke (Figure 7.14) in which the width of the anomaly varies not only with electrode configuration but also with the ratio of the dyke width to electrode separation. An example of an apparent resistivity profile across a buried hemicylindrical valley is shown in Figure 7.15. The field and modelled profiles are very similar. The mathematical treatment of apparent resistivity profiles across vertical boundaries is discussed in detail by Telford et al. (1990). The important consideration arising from this discussion is that different array types and orientations across an identical boundary between two media with contrasting resistivities will produce markedly different anomaly shapes. Thus interpretation and comparison of such profiles based simply on apparent resistivity maxima or minima can be misleading; for example, if maxima are used to delimit targets, a false target could be identified in the case of maxima doublets such as in Figure 7.14. Similar complex anomalies occur in electromagnetic data (Section 9.4.3). Furthermore, the type of anomaly should be anticipated when considering the geological target so that the appropriate electrode configuration and orientation can be chosen prior to the commencement of the survey.
2
1
5
3
Figure 7.15 Apparent resistivity profiles across a buried valley: (A) theoretical profile, and (B) measured profile. After Cook and van Nostrand (1954) (see Parasnis 1986)
7 0r-~_-T2_-.:;..3_....:J.T---=:;5~--T6_-;7
6
(b I
(a I
0
t
D.H. :
.
in 200
\, I
t
/
~
r---t-A+---+---::+---+---+---i
\
/'\.
,1:\
I, \ V
iii
...GI
...c
~
c
a.
~ 100
Vert.
.. ...J
~Ia M a N 10 ~
Surface I
I
I p'~"P."':"J I 'I ':. './f
f-p":50
t-p'=250 i
I
I
I
I
I p'l
"
I
I
I
I
I
I
I
,
I
IVI>rt. scalI> : f ior. scalI> I
I
b
o W
___ ;,.",;; f--
I
20 40 .60
I
I
I
II \
I
I .. I
scale: 3111 Hor.scalCi? \
a~ a~AIIlIVlllln: Sur act' J. 'TII
I
I
E 2!!
I
20
::>hO It'j 'Limestone I
T!II I!
I
I
I
I
I
I
+
0
I
40 &0.
Electrical resistivity methods
7.4
MODES OF DEPLOYMENT
There are two main modes of deployment of electrode arrays. One is for depth sounding (to determine the vertical variation of resistivity) - this is known as vertical electrical sounding (VES). The other is for horizontal traversing (horizontal variation of resistivity) and is called constant separation traversing (CST) (also called 'electrical resistivity traversing', ERT). In the case of~ul!i-elec~rode arrays,! two forms are available. Microprocessor:::controlled resistivity' traversing (MRT) is used particularly for hydrogeological investigations req uiring significant depths of penetration. Sub-surface imaging (SSI) or two-dimensional electrical tomography is used for very high resolution in the near-surface in archaeological, engineering and environmental investigations.
7.4.1
Vertical electrical sounding (VES)
As the distance between the current electrodes is increased, so the depth to which the current penetrates is increased. In the case of the dipole-dipole array, increased depth penetration is obtained by increasing the inter-dipole separation, not by lengthening the current electrode dipole. The position of measurement is taken as the midpoint of the electrode array. For a depth sounding, measurements of the resistance (bV/I) are made at the shortest electrode separation and then at progressively larger spacings. At each electrode separation a value of apparent resistivity (Pa) is calculated using the measured resistance in conjugation with the appropriate geometric factor for the electrode configuration and separation being used (see Section 7.3). The values of apparent resistivity are plotted on a graph ('field curve') the x- and y-axes of which represent the logarithmic values of the current electrode half-separation (AB/2) and the apparent resistivity (Pa)' respectively (Figure 7.16). The methods by which these field curves are interpreted are discussed in detail in Section 7.5. In the normal Wenner array, all four electrodes have to be moved to new positions as the inter-electrode spacings are increased (Figure 7.17A). The offset Wenner system has been devised to work with special multicore cables (Barker 1981). Special connectors at logarithmically spaced intervals permit a Wenner VES to be completed by using a switching box which removes the necessity to change the electrode connections physically. Note that the offset Wenner array requires one extra electrode separation to cover the same amount of the sub-surface compared with the normal Wenner array. When space is a factor, this needs to be considered in the survey design stage. In the case of the Schlumberger array (Figure 7.17C), the potential electrodes (PtP z ) are placed at a fixed spacing (b) which is no more
441
442
An introduction to applied and environmental geophysics
1000
I ..-.
E
c:
---.....
;>,
100
:;:; III In Q)
Q) ....
~
a. a.
«
-+
./
".'\
.S;
.........c
.- ........
./
+\
10
..+ /+ +
. /. . ..
\
/
\_/•
/'
./ ./'
100
10
1000
AB/2 (m)
than one-fifth of the current-electrode half-spacing (a). The current electrodes are placed at progressively larger distances. When the measured voltage between P 1 and P 2 falls to very low values (owing to the progressively decreasing potential gradient with increasing current electrode separation), the potential electrodes are spaced more widely apart (spacing b 2 ). The measurements are continued and the potential electrode separation increased again as necessary until the YES is completed. The tangible effects of so moving the potential electrodes is discussed at the end of Section 7.4.4. A YES using the Schlumberger array takes up less space than either of the two Wenner methods and requires less physical movement of electrodes than the normal Wenner array, unless multicore cables are used. The dipole-dipole array is seldom used for vertical sounding as large and powerful electrical generators are normally required. Once the dipole length has been chosen - i.e. the distance between the two current electrodes and between the two potential electrodes - the distance between the two dipoles is then increased progressively (Figure 7.17C) to produce the sounding. The square array is rarely used for large-scale soundings as its setting out is very cumbersome (Figure 7.17E). The main advantage of the electrode configuration is the simplicity of the method when setting out small grids. In small-scale surveys investigating the three-dimensional extent of sub-surface targets, such as in archaeology, the square sides are of the order of only a few metres.
Figure 7.16 A vertical electrical sounding (VES) showing apparent resistivity as a function of current electrode half-separation (AB/2)
Electrical resistivity methods
.
(A)
c,
P,
c,
P,
.
.)(.
8'"
8",2
)(
8",3
•
8",4
)(
c,
P,
P,
(B)
Ar=e&iC
1 A.
1 units
)(
)(
c,
443
10
~
8",5
x = array centre E
(1)J IE
8= 1 units
a=2 8=3
...- - - - - - - - - - - - - - - - - - - - - - - - - - - - . 8 C 0 E
A
•
c,
(C)
P, P,
C,
a,. b,
=$=
b, 80. b, 8 •• b,
fO-- s----lt •
(0)
8 2,
I
)(
•
•
)II(
•
P,
P,
c, C,
P,
I
.)(.
8,;. b 2 8,;.
c, P,
)( )(
•
•
C,
•
P,
b2
n=1 n",2 n=3 n=4 n=5
•
)(
c,
a= 4
•
P,
(E) 8 = 4 units
8=3 8=2
a=1
Figure 7.17 Expanded arrays (with successive positions displaced for clarity) for: (A) Wenner, (B) offset Wenner, (C) Schlumberger, (D) dipole-dipole and (E) square arrays
444
7.4.2
An introduction to applied and environmental geophysics
Automated array scanning
In 1981 Barker published details of the offset Wenner array using multicore cables and multiple electrodes for YES investigations. In 1985, Griffiths and Turnbull produced details of a multiple electrode array for use with CST. This theme was developed by van Overmeeren and Ritsema (1988) for hydrogeological applications and by Noel and Walker (1990) for archaeological surveys. For deeper t sounding, where multicore cabling would become prohibitively heavy, the cable is wound into 50m sections on its own drum with an addressable electronic switchingunit and power supply mounted in the hub of each cable reel. The switching units are controlled by a laptop computer which can switch any electrode to either of two current or two potential cables which connect the entire array of drum reels. This system is known as the microprocessor-controlledresistivity traversing sy.stem (Griffths et al. 1990). • In van Overmeeren and Ritsema's continuous vertical electrical sounding (CVES) system, an array of multiples of 40 electrodes is connected to a microprocessor by a multicore cable. Usiing software control, discrete sets of four electrodes can be selected in a variety of electrode configurations and separations and a measurement of the resistance made for each. Instead of using one cable layout for just one YES, the extended electrode array can be used for a number of YES, each one. offset by one electrode spacing. If the first YES is conducted with its centre between electrodes 15 and 16, for example, the next YES will be centred between electrodes 16 and 17, then 17 and 18, 18 and 19, and so on. A field curve is produced for each sounding along the array and interpreted by computer methods (see Section 7.5.3) to produce a geo-electric modeL of true layer resistlvltTes and thickness for each YES curve. When each model is displayed adjacent to its neighbour, a panel of models is produced (Figure 7.18) in which the various resistivity horizons can be delimited. It is clear from Figure },18Dthat the CVES interpretation is closest to the known physical model .compared with those for either the tripotential alpha or beta/gamma ratio sections (Shown in Figure 7.18B and C respectively). This particular method requires special equipment and associated computer software, but it highlights a novel application of both,field method and data analysis to improve the resolution of shallow resistivity surveys. In sub-surface imaging (SSI), typically 50 electrodes are laid out in two strings of 25, with electrodes connected by a multicore cable to a switching box and resistance meter. The whole data acquisition procedure is software-controlled from a laptop computer. Similar products have been produced, such as the LUND Automatic Imaging System (ABEM), and MacOhm 21 (DAP-21) Imaging System (OYO), and the Sting/Swift (Advanced Geosciences Inc.), among others.
Electrical resistivity methods
445
(A)
c
0
a: 2!
III III
a=
0.
Cll
j
rn
a=10 J
Cll 'tl 0
a=14,
u
a=18-
.
:0-
(8)
-.. Cll
61 .."") j
-_/
~~~
4i a=24,
c:
0
a= 2
III III
a= 6
.
:0-
(e)
0.
rn
Cll
a=10 -
Cll 'tl
a=14·
ij
a=18 J
.. 0
i
1
QI
j
QI
a=24 ;
-E
(D)
-
.s:.
0. QI
'tl
01
m~~~~~~~~~;~
21 4
i~~~~_~'.~~~M~~!~~~i~~~~I_I*~~~~~:.
1
81
101
,
i
'
~.
,
,
'I'
I
j
)1'
!
I' iii
Ii
i
j
i:
I
i
1I,'~1
i
o
loam
~l'I!;
I! i , ! . 1'1 I-,;-:-,----'-!-;-U_._ II
i
II
c=J sandy ,
I
I
100
200
300
m
High-resolution soil As with van Overmeeren and Ritsema's eYES method, a discrete Figure 7.18 survey using a scanned array. (A) Soil set of four electrodes 'with the shortest electrode spacing (n = 1; see section.determined by shallow hand! Figure 7.19) is addressed and a value of apparent resistivity obtained. drilling. Pseudo-sections obtained Successive sets of four electrodes are addressed, shifting each time by, using (B) Wcnncr tripotcntial alpha one electrode separation laterally. Once the entire array has been and (C) beta/gamma arrays. (D) Con~~anned, the electrode separation is doubled (n = 2), and the process tinuous vertical electrical sounding repeated until the appropriate number of levels has been scanned. rcsults with true resistivities indicated. The values of apparent resistivity obtained from each measurement From van Overmeeren and Ritsema (1988), by pcrmission are plotted on a pseudo-section (Figure 7.19) and contoured. The methods of interpretation are described in more detail in Section 7.5.6. There are considerable advantages in using SST or equivalent c
I~
i
~~~ ~--~~~~-~~~-~~-~~~------~~~~~~~------~~~~~-~
I
'J
I'
Ll " -1+ ..--I.. -,-,I--l-iII _:_.:-._LI_ ' /-1' 1_I-, ' - -:-1- ; ,- -!,-;-IF"\'. """"1
I
~~~~_.'.~
j
61
, 'i
,.
\
446
An introduction to applied and environmental geophysics
Figure 7.19 Example of the measurement sequence for building up a resistivity pseudo-section. Courtesy of Campus Geophysical Instruments Ltd.
Station 3
I
I
C1
P1
3a
P2
3a
C2 3a
Station 2 I
,
C1
, C1 I
n =1 n = 2 n'= 3
2a
P1,
P2
2a II
I
n==5
~2
Station 1 I
P1
a
I
a A
•
1
I
P2 I
a
C2 I
•
•
•
•
2
•
•
• •
•
•
3 n= 4
2a
•
•
4
•
•
•
•
•
•
•
5
methods. With multicore cable and many electrodes, the entire array can be established by one person. The acquisition of apparent resistivity data is controlled entirely by the software whose parameters are selected at the outset. By changing the inter-electrode spacing between electrodes, the 'vertical and horizontal resolutions can be specified to meet the objectives of the survey. For example, the horizontal resolution is defined by the inter-electrode spacing,' and the vertical resolution by half the spacing. For example, using a 2m inter-electrode spacing, the horizontal and vertical resolutions are 2 m and 1 m, respectively, for the pseudo-section display. Whether sub-surface features can be resolved at a comparable scale is determined also by the lateral and vertical variations in true resistivity. 7.4.3
Constant-separation traversing (CST)
Constant-separation traversing uses a manul electrode array, usually the Wenner configuration for ease of operation, in which the electrode separation is kept fixed. The entire array is moved along a profile and values of apparent resistivity determined at discrete intervals along the profile. For example, a Wenner spacing of say 10m is used with perhaps 12 electrodes deployed at anyone time at 5 m intervals. Alternate electrodes are used for anyone measurement (Figure 7.20) and instead of uprooting the entire sets of electrodes, the connections are moved quickly and efficiently to the next electrode along the line, i.e. 5 m down along the traverse. This provides a CST profile with
Electrical resistivity methods
447
Figure 7.20 A constant-separation traverse using a Wenner array with 10m electrode spacing over a clayfilled solution feature (position arrowed) in limestone
....E
~
~
'S
:;;
120
'iii Q) ~
E Q)
100
~
III
Co Co
c(
60
III
Clay infill
~
40 10
15
20
25
30
35
40
45
Position (m)
electrode separation of 10 m and station interval of5 m. The values of apparent resistivity are plotted on a linear graph as a function of distances along the profile (Figure 7.20). Variations in the magnitude of apparent resistivity highlight anomalous areas along the traverse. Sorensen (1994) has described 6."ulled array continuous electrical profiling' technique (PA-CEP). An array of heavy steel electrodes, each weighing 10-20 kg, is towed behind a vehicle containing all the measuring equipment. Measurements are made continuously. It is reported that 10-15 line kilometres of profiling can be achieved in a day. The quality of results is reported to be comparable to that of fixed arrays with the same electrode geometry. 7.4.4
Field problems
In order for the electrical resistivity method to work using a collinear ", array, the internal resistance of the potential measuring circuit must . be far higher than the ground resistance between the potential electrodes. If it is not, the potential circuit provides a low-resistance alternative route for current flow and the resistance measured is completely meaningless. Most commercial resistivity equipment has an input resistance of at least 1 Mn, which is adequate in most cases.
448
An introduction to applied and environmental geophysics
In the case of temperature glacier ice, which itself has a resistivity of up to 120 MQ m, a substantially higher input resistance is required (preferably of the order of 10 14 Q). Electrical resistivity soundings on glaciers are complicated by the fact that ice does not conduct electricity electronically but by the movement of protons within the ice lattice and this causes substantial polarisation problems at the electrode-ice contact. Consequently, special techniques are required in order to obtain the relevant resistivity data (Reynolds 1982). Perhaps the largest source of field problems is the electrode contact resistance. Resistivity methods rely on being able to apply current into the ground. If the resistance of the current electrodes becomes anomalously high, the applied current may fall to zero and the measurement will fail. High contact resistances are particularly common when the surface material into which the electrodes are implanted consists of dry sand, boulders, gravel, frozen ground, ice or laterite. If the high resistance can be overcome (and it is not always possible), there are two methods that are commonly used. One is to wet the current electrodes with water or saline solution, sometimes mixed with bentonite. The second method is to use multiple electrodes. Two or three extra electrodes can be connected to one end of the current-carrying cable so that the electrodes act as resistances in parallel. The total resistance of the multiple electrode is thus less than the resistance of anyone electrode (see Figure 7.21 and Box 7.12). However, if this method is used, the extra electrodes must be implanted at right-angles to the line of the array rather than along the direction of the profile. If the extra electrodes are in the line of the array, the geometric factor may be altered as the inter-electrode separation (C 1-P 1-P 2 -C 2) is effectively changed. By planting the electrodes at right-angles to the line of the array, the inter-electrode separation is barely affected. This problem is only acute when the current electrode separation is small. Once the current electrodes are sufficiently far apart, minor anomalies in positioning are insignificant. This also applies when laying out the survey line to start with. Box 7.12
Resistances in parallel
Total resistance of multiple electrodes is RT : n
I/R T
= I/R 1 + I/R 2 + ljR 3 + ·.. 1/R n =
L (I/RJ i=l
For example, if'1 ='2 = O.2R and'3 ='4 = O.5R, then: l/R r = 1/0.2R
+ IjO.2R + 1/0.5R + IjO.5R + I/R = 15/R.
Thus RT = R/15, and R r is much less than the lowest individual resistance ( = R/5).
Electrical resistivity methods
449
(A)
,,-~ b II ' __
C, '2- IY
'__
"-".11 .'
P
............... ' -e
P2
C2
.
.
,J------ a------t------ a------+----- a-----' I
If y« a, b ~ a
'. _
(B)
...
'"
• °
0
. :• •
•
'
..
-0"
•
.' .
. .. ..' •
.'
"0
.'
I
'.
"0
·0
....
'. •
•
••
°0
•
Ground level
••
.'
••
0• • • • • 0.
'
•
.......
"0·
Main electrode (resistance. R)
Supplementary electrodes
P',
(C)
--------~--------_:~~~~::
:
-----q-----a : C
-~~~~---~--------~ __ P, P2 - C, Actual distance and and
C, P'2 < 2a
C'2P', Po
a
P, > P, > Po
"\,
,
\ Small h 2 ,
Large
h,
Small h 2 '
\ \
(E) Type HK
(F) Type KH
---- K·------t
P,
---- Ho----+-j
------H----.
P,
I------K--.
P, < P, > Po < P.
(G)
,----------------
1000
, @1000
I I
9.
of ~
I I I I I
---, '@250, I 4 I
E
I
100
..,
..l--=-::f---'r-;-,
,
°iii
e c e
I I I I I I I
~
~
,
I
I I
6' I
'@101
10
1
10
100
Electrode separation AB'2 (m)
Electrical resistivity methods
The relative magnitudes of the true resistivities obtained from the levels ofthe flat portions or shoulders of the graph are a useful starting point before more involved interpretation. For example, in Figures 7.26A and B, the only difference between the two models is the resistivity of layer 2. In Figure 7.26A, layer 2 resistivity is less than those for both layers 1 and 3. In Figure 7.26B, the second layer resistivity is between those for layers 1 and 3. In the case of Figure 7.26D, if the second layer is very thin (dashed line for small hJ it may not be evident on the curve that this layer exists, i.e. its effects are 'suppressed'. 'Suppression' is discussed in more detail in Section 7.5.4. From Figure 7.26G, it can be seen that the number of layers identified is equal to the number of turning points (TP) in the curve, plus one. The presence of turning-points -iriolcafes sub-surface interfaces, so the number of actual layers must be one more than the number of boundaries between them. However, the coordinates of the turning points in n6 way indicate 'the depth to a boundary .or provide specific information about the true resistivities (Figure 7.26G). From the curve shape alone, the minimum number of horizontal layers and the relative magnitudes of the respective layer resistivities can be estimated. :~
7.5.2
Master curves
Interpretation of field curves by matching against a set of theoretically calculated master curves is based on the assumptions that the model relates to a horizontally stratified earth and that successively deeper layers are thicker than those overlying. Although this second assumption is rarely valid, the use of master curves does seem to provide a crude estimate of the physical model. Synthetic curves for two-layer models can be represented on a single diagram (Figure 7.27), but for three-layer models the range of graphs is very large.and books of master curves have been published (Mooney and Wetzel 1956; European Association of Exploration Geophysicists ~991). It is only practicable to use the master curves method for up to four layers. If more layers are present, the graphical approach is far too cumbersome and inaccurate. Three- and four-layer models can also be interpreted using master curves for two layers with the additional use of auxiliary curves (Figure 7.28) as outlined below. The field data~ smoothed and corrected as necessary, are plotted on a log-log graph on a transparent overlay at the same scale as the master curves. The overlay is placed on the master curves and, keeping the x- and y-axes of the two graphs parallel, the overlay is moved until the segment of the field curve at shortest electrode spacings fits one of the master curves,and its k value is noted (Figure 7.29; in this case, k = - 0.3). The position of the origin of the master curve is marked (A) on the overlay, which is then placed over the auxiliary curve sheet and the line for the same k value is traced on
455
Figure 7.26 (opposite) Apparent resistivity curve shapes for different resistivity structures: (A) to (D) are three-layer models; (E) and (F) are four-layer models; (G) shows a block model for the layer resistivities and thicknesses and the resulting apparent resistivity curve. Neither the minimum nor the maximum apparent resistivities occur at electrode separations equivalent to the layer depths. To penetrate to bedrock, electrode separation should be about three times the bedrock depth for a Schlumberger array
456
An introduction to applied and environmental geophysics Schlumberger L / h - - +
,
~
_ _- 0 . 8
~I
~I
0;'
Eo
~_-_--07
(/)1
"" ~I
~_-----06
~:
05
~:
04
.01
'Cross' for Wenner or Schlumberger field curve plotted uSing total array length (2LI as ordinate
r .,
Co
Schlumberger 'cross'
-,
..JI I
0.3
:
0.2
'H~==t=E====
00 01 -0.1
-----L......-.J----------o2 ----.-~---------0.3 ~-y---t_---------04
---.--t--------- -05 ~-:----+---------
-0.6
o --.L.._--l II - - - - - - - - - - 0 7 .I> l-
• (8)
f/) f/)
w
a:
final layering
(C)
10
100
1000
ELECTRODE SPACING, a, or DEPTH
the observed and model resIstIvIty curves to a mInImUm and is determined by trial and error. The starting model is used to generate a theoretical synthetic sounding curve which is compared with the field data. An iterative process is then carried out to adjust the resistivities of the model while keeping the boundaries fixed. After each iteration the theoretical curve is recalculated and compared with the field data. This process is repeated until the RMS difference between the two curves reaches a minimum (Figure 7.33). Zohdy's method has been developed by Barker (1992) for the inversion of SSI apparent resistivity pseudo-sections and more recently by using a;deconvolution method(Barker, personal communication). Consequently, it is possible to produce fully automated
Figure 7.33 Automatic sounding inversion technique. (A) Observed data and initial layering. (B) Shifted layering and resulting model sounding curve. The difference (e) between the model and observed curves is used to apply a correction (c) to the layering. (C) The final layering and resulting model curve that is closely similar to the observed data. From Barker (1992), by permission
466
An introduction to apJ: :ied and environmental geophysics
inversions of SSI pseudo-sections. The final results are displayed also as pseudo-sections in terms of the variations in true resistivity with depth as a function of distance along the array. Examples of inverted pseudo-sections are given in Section 7.7. In addition to the above inversion routines, others have been produced, often in association with particular equipment, and also as specific developments of true tomographic imaging (e.g. Shima 1990; Daily and Owen 1991; Noel and Xu 1991; Xu and Noel 1993). Commercially available\lmaging inversion pack.~g~~ are available from a number of sources and are related to a style of data acquisition and equipment. Packages vary from those which can operate easily on a laptop computer, more sophisticated processing may require the computational power of a workstation with full colour plotting facilities. ,I Finite-element forward modelling can be undertaken using commercially available ·software. The resistivity response for a twodimensional model is calculated and displayed as a pseudo-seCtion for comparison with the original field data. This approach is used to help generate realistic sub-surface geometries in definable model structures (e.g. Figure 7.34).
Figure 7.34 Final interpretation of faulted Triassic sequence in Staffordshire, UK. (A) Two-dimensional finite difference model. (B) Computed apparent resistivity pseudo-section. (C) Field data. (D) Geological interpretation based on (A) and additional information. From Griffiths et al. (1990), by permission
w (A)
-
"
%
" 75
E
:l. 0.'"
aMRENT)OO ....
~.
~
470
An introduction to applied and environmental geophysics
A
nc METeRS SULFIDE
lONE
.1
l +I "
"-
" '-.., CURRENT ELECTRODE
DRILL HOLE-
1000
METERS
CUP.RENT
ELECTRODE
....
/
METERS
o
100
,-I
200
METERS ~
o
10 OHM-METER CONTOURS
I 100
200
o •
(Aj
OAlL.~ ~OLE
COLLAR DOWN-HOLE CURRENT ELECTRODE
METERS
o
(6)
a conductive body is bounded to the north and south (as indicated by ,the marked lows) and extends a limited way in an east-west direction. This interpretation has been confirmed by other investigations.
7.7
APPLICATIONS AND CASE HISTORIES
7.7.1
Engineering site investigations
7.7.1.1
I"'"""
Sub-surface collapse features
In a small village in east Devon, a 5 m diameter hole appeared overnight in the middle of the road. The local water main had been ruptured and had discharged for over 12 hours and all the water had disappeared down a fissure into underlying limestone. Several of the local buildings started to crack badly, and on investigation it was found that the rafted foundations of several houses had broken and the houses were literally cracking open at the seams, resulting in the emergency evacuation of the residents. A resistivity survey was initiated in order to determine the subsurface extent of the problem prior to drilling. Fortunately, the front gardens of the houses affected were all open-plan so there was no difficulty in access, but space was at a premium. A series of constantseparation traverses was instigated using the Wenner array with electrode separations of 10, 15 and 20m. The resulting apparent resistivity values were plotted as a contour map (Figure 7.39). It was
I 100
200
(C)
Figure 7.38 (A) Current electrode configurations. (B) Actual mise-a-Iamasse apparent resistivities measured on the surface around inclined borehole D-9. Contours are every 10 n m. (C) Terrain-corrected apparent resistivities for the same survey with an interpreted conductive zone indicated. From Oppliger (1984), by permiSSIOn Figure 7.39 (opposite) (A) Apparent resistivity isometric projection obtained using constant-separation traverses with an electrode separation of 10m. (B) Modelled microgravity profile that would be expected for the geological model shown in (C): interpreted depth to limestone constrained by drilling. A north-south profile is shown in Figure 7.20. The position of a clay-filled solution feature is arrowed
Electrical resistivity methods
(A)
(B)
I
~-0.15
m
~-0.20 j
(ij
E
-: =1
c:
~
(1l
~
J
3
o
-0.25 "
~
~
J
3
C> -0.30 -:! ~
035 -
1
-0.40 Ii I i , ' 1 l l l i i 111111111' i i i i II Ii i [ ' i l -40.00 -20.00 0.00 20.00
. i l i Ii i i i i i I i f
40.00
'i
i iiil iii i
60.00
I
80.00
Position (m) (C)
Soil 1.8 Mg m,3 3
Clay infill 2.0 Mg m· Limestone 2.4 Mg m,3
471
472
An introduction to applied and environmental geophysics
clear that where the hole had appeared, there was a deep infill of clay. It was this that had slipped through a neck of a fissure into a cave beneath, resulting in subsidence beneath the foundations of the houses and the rupture of the water main. The discharging water disappeared into this newly discovered cavern. The clay depth decreased uphill and suddenly increased again, indicating further clayfilled fissures. On drilling these resistivity anomalies, the depth to limestone was confirmed. One drillhole penetrated the cave but failed to locate the bottom; the cave was at least 20 m deep.
7.7.1.2
Burial oftrunk sewer
A route for a proposed new trunk sewer in South Wales was investigated using electrical resistivity methods because access for drilling equipment was not possible. Both vertical electrical soundings and constant-separation traverses were used along the route and compared with available borehole data from the National Coal Board (Prentice and McDowell 1976). The material through which the sewer trench was to have been dug consisted of superficial deposits overlying Coal Measure sandstone and mudstone. The Coal Measure material was anticipated to be massive and strong and thus hard to excavate, while saturated superficial deposits and Coal Measure shales were thought to provide very unstable trench walls. The CST results using a Wenner array with 10 m electrode separation and 10 m station interval revealed locations where sandstone bedrock was interpreted to be close to the surface which would have required
1100 1000 E 900 9- 800 ~ .s; 700 ~ 600 'iij G> '500 "E G> 400 'til a. 300 a. < 200 100 0
0
S ~
Q. III 0
Figure 7.40 Constant-separation traverse data obtained along the proposed route of a new trunk sewer in South Wales, with the interpreted geological section. After Prentice and McDowell (1976), by permission
Ground surface Excavation depth (3m) - - - - - -
-;7'
Sandy clay
",?=-~,:::;.;:r11"'5=~~;;:,:;=:;;=n=r7"'7
Sandstone 60m I
.
._~.......
.-' 85
/_.-.",,"-./
......- .
90
95
100
105
Resistivity stations
110
115
120
125
130
Electrical resistivity methods
blasting for the excavation for the new sewer (Figure 7.40). Seismic refraction was also used to obtain acoustic velocities, which in turn were used to determine whether blasting or ripping techniques should be used in the excavation.
7.7.1.3
Location ofpermafrost
The presence of massive ground ice and frozen ground provides considerable problems to engineers involved in construction projects. First there are the difficulties in excavation, and secondly, substantial problems can emerge with the thawing of such affected ground. It is therefore vital that ice wedges and lenses, and the extent and degree of permafrost, can be determined well in advance. Ice has a very high DC electrical resistivity in the range from 1MQ m to 120 MQm (Reynolds and Paren 1984) and therefore forms'a particularly resistive target. A variety of geophysical profiles over a proposed road cutting near Fairbanks in Alaska are illustrated in Figure 7.41. Data obtained in the spring show more variability and resolution than when an active layer of thawed ground is present, as in the autumn measurements (Osterkamp and Jurick 1980). Other geophysical methods which are used successfully in this application are electromagnetic profiling, microgravity and ground radar surveymg.
7.7.1.4
Location ofburiedfoundations
As part of a trial survey in January 1993, electrical resistivity subsurface imaging was used at a disused railway yard in order to locate old foundations concealed beneath railway ballast. Details of the geophysical survey have been described in more detail by Reynolds and Taylor (1994,1995) and Reynolds (1995). . i, The SSI survey was carried out adjacent to a metal chain-link fence ~Yand an old diesel tank, and about 3 m from an existing building. It was thought that the remains of two former buildings might still be present beneath the railway ballast and the existing building. The site was totally unsuitable for electromagnetic profiling, because of the above ground structures. It was also unsuitable for gr0tl!1.d penetrating radar owing to the coarse ballast and potentially conductive ash also found on site. Despite extremely high electrode contact resistances, a 25 m long array was surveyed with an inter-electrode separ[' ation of 1m. This provided a vertical resolution of 0.5 m or better. The ; apparent resistivity data were! filteredto remove noise spikes and {, displayed as a pseudo-section· (Figure 7.42 A) which was inverted using a deconvolution technique (Barker, personal communication). The final pseudo-section of true resistivities against depth shows a general increase in resistivity with depth (Figure 7.42B). In particular, it revealed two areas of extremely high resistivity ( > 125000 Q m)
]
473
474
An introduction to applied and environmental geophysics
- - Spring ....•..•. Autumn
...........................-............ ....
...••..........•.....••._..... ............
.
.
....
Resistivity
::::E I
d >-
t-
:>
...:
i=
,
::
(/)
ii5 w
./
.-"""..'
a::
...........
tz w
a::
rt a.
«
100
100
z
o
!;i > w
-'
w
o
100
200
&)0
400
MASSIVE ICE OR ICE RIQ-I SOILS
at a depth of about 1 m which had very flat tops to the anomalies. These were interpreted to be due to buried foundations. The main anomaly (between 6 and 11 m along the array) was found to correlate with the outline of one former building on an old plan. The second feature (starting at around 18 m) is thought to be due to the other old building. However, the location was found to be several metres further away from the first building than indicated on the plans. The
Figure 7.41 Massive ice and frozen ground in a sub-surface profile of a proposed road cut near Fairbanks, Alaska. Also shown are the spring and autumn survey data obtained using electrical resistivity constant-separation traversing and electromagnetic induction (EM31). Massive ground ice produces significant apparent resistivity highs. From Osterkamp and J urick (1980), by permission
Electrical resistivity methods
475
Distance (m)
o
5
10
15
20
(A)
Apparent resistivity in kOhm.m Distance (m) (B)
o
5
10
15
20
Railway ballast fill
-§. E
~
»125
MODEL True resistivity in kOhm.m
depth to the foundation was thought to be reasonable as adjacent brick slabs excavated a few metres away were found at a comparable depth. 7.7.2
7.7.2.1
Groundwater and landfill surveys
Detection ofsaline groundwater
In the mid-1950s, a comprehensive electrical resistivity survey programme was initiated in order to map out saline groundwater in areas of the Netherlands below or at mean sea level. Figure 7.43 shows schematically the nature of the hydrogeology in the western part of the Netherlands. The vertical electrical soundings provided a means of. obtaining information about the vertical distribution of fresh, brackish and saline water bodies and their areal extent (Figure 7.44). Pockets of saline water were found which were thought to be remnants from before the fifteenth century after which time the present sea-dyke formed, cutting off the sea. To the west of Alkmaar, some 30 m of saline water was found above tens of metres of fresh water separated by an impermeable clay layer. Major demands for construction sand for the building of new roads and urbanisation
Figure 7.42 Electrical resIstIvIty subsurface imaging pseudo-sections: (A) apparent resistivity profile, and (B) true resistivity-depth profile, over buried concrete slabs at 1 m depth. From Reynolds and Taylor (1995), by permISSIOn
!~ !
476
An introduction to applied and environmental geophysics
I
1
(O·m)
w
-J W
430 20
425
10
20
40
'0
40 CLAY LAYER
420 +,-,-L,-,-,----.-,l-,-,---.-".J,--,..-,--,--,L,----."---r'--.-,-,----.,J-,,,-,-,.-,-,--,, 100 -250 -200 - 150 - 100 - 50 o 50 DISTANCE (m)
and displays as resIstIvIty panels have revealed significant zones with anomalously low resistivities (Figure 7.47). These have been interpreted as being contaminant plumes arising from the landfill. The displays shown in the figure are orientated parallel to the flank of the landfill, but at 10 m and 70 m distance away from it. Sub-surface imaging pseudo-sections across a landfill are shown in Figure 7.48. The three panels illustrate the observed apparent
Figure 7.47 Two parallel resIstlVlty sections based on the interpretation of Schlumberger soundings at the Novo Horizonte landfill site, Brazil. The profile in (A) is closer to the landfill than that shown in (B). The background resistivities above the basal clay are high; the lower values in the centre of the sections are assumed to be due to contamination. Note that the conductive zone in (B) is apparently more shallow than in (A). From Monier-Williams et al. (1990), by permission
Electrical resistivity methods
481
(A)
n
i
=6
(B)
3!1t1
: .;
16
:
:
iiiiHIHHHH
mmmmm • • •_
24
32
48
RESISTIVITY in oba-.
(C)
•••
64
96
LANDFILL
"
"'-------~ LEACHATE /
CONTAMINA TION
reslstlVlty data, the inverted true resistivity~depth model and a schematic interpretation. In this case, the depth and geometry of the landfill were known at the outset. The zone of low resistivity associated with the saturated landfill extends more deeply than had been expected. This is interpreted as indicating the leakage of leachate through the base of the landfill (Barker 1992). A further example of a sub-surface imaging pseudo-section inverted model is shown in Figure 7.49 (Reynolds 1995). The data were acquired over a closed shallow landfill constructed as a 'dilute and disperse' site over river gravels. The electrical image shows the thin capping material, the waste material and the basal gravels quite clearly. The image is entirely consistent with depths known from boreholes on site.
Figure 7.48 (A) Wenner apparent resistivity pseudo-section measured across a landfill. Electrode spacing = 10 m. (B) Resistivity depth section obtained after eight iterations. (C) Approximate section across the landfill based on existing information. From Barker (1992), by permission
482
An introduction to applied and environmental geophysics
Position (m)
o
8
32
24
16
40
56
48
64
72
80
/*'-.1 E 2 '-' ~ ..... 3
fr4
Q 5
6 Model resistivity in Ohm.m I88ll88lIl IIl88llIlIIl
16
~
Electrode spacing = 2 m.
Ohm.m ::::::::::::::
43
~
69
llI88S88 _
95
_
_
_
121
7.7.3 Glaciological applications Electrical resistivity methods have been used since 1959 to determine glacier ice thickness. Measurements were first obtained on European glaciers on temperate ice (i.e. ice at its pressure melting point). In 1962, resistivity measurements were made on polar ice (i.e. ice well below its pressure melting point) and were found to be anomalously low by up to three orders of magnitude compared with temperate ice values. Whereas the electrical resistivity behaviour of polar ice is now reasonably understood (Figure 7.50; Reynolds and Paren 1984), the electrical behaviour of temperate ice is still poorly understood. In the 1970s a considerable amount of work was undertaken to develop field data acquisition in Antarctica. Interpretation methods were developed to yield information on vertical thermal profiles through the ice mass and whether or not ice shelves afloat on sea water were melting or freezing at their base. All of these data contribute to an understanding of ice dynamics (rate of ice movement, etc.) and the structure of the ice masses under study. A series of vertical electrical soundings has been made on George VI Ice Shelf along a flow line of Goodenough Glacier which flows westwards from the Palmer Land Plateau in the Antarctic Peninsula (Figure 7.51). The field curves were modelled to take into account thermal effects and the resulting interpretations are shown in Figure 7.52. The estimated ice thicknesses and rates of bottom melting were in good agreement with those determined independently (Reynolds 1982).
_
147
8IIl888I
~
173
199
Figure 7.49 Electrical reSIStIVIty pseudo-section acquired over a closed landfill in north Wales. From Reynolds (1995), by permission
Electrical resistivity methods
483
4
-E
o
2
•
C
'-"
5
:?:' 10 >
"+:;
en .en Q)
..
8 6
•
L-
C
Q)
4
L-
eu a. a.
•
«
2
4
10
-10
0
3·7
3·8
-30
-20
3·9 10001T (K
4·0
4·1
1 )
Other uses of resistivity measurements have been made by Haeberli and Fisch (1984) who drilled holes with a hot-water jet drill through Grubengletscher, a local glacier in Switzerland. By using a grounded electrode beyond the snout of the glacier and the drill tip as a mobile electrode, they were able to detect the point at which the drill tip broke through the highly resistive ice into the more conductive substrate (Figure 7.53A). Consequently, they were able to determine the ice thickness much more accurately than by using either the drilling or surface radio-echosounding. With debris-charged ice at the glacier base it is difficult to tell when the glacier sole has been reached judging by thermal drilling rates alone. The radio-echosounding depth measurements were found on average to be accurate to within 5%, but generally underestimated the depth. Electrodes were planted at the ice-bed interface at the ends of each of 14 boreholes and standard resistivity depth soundings were undertaken as if the glacier were not there (Figure 7.53 B).
Figure 7.50 Resistivity of ice as a function of temperature. Mean values from georesistivity sounding of ice at 100m or deeper are plotted with estimated uncertainties against the estimated layer temperature from a wide variety of sources. Laboratory measurements on ice cores examined over a range of temperatures are shown by continuous lines. A regression line for the data is given by a dashed line. Given a particular temperature, the ice resistivity can be predicted within a factor of 2 or better. After Reynolds and Paren (1984), by permission
484
An introduction to applied and environmental geophysics
Figure 7.51 Apparent resIstIvIty sounding curves obtained using a Schlumberger array at three sites along a glacial flow line on George VI Ice Shelf, Antarctica. In (A) and (B) two orthogonal soundings are shown at each site. Below each curve is the interpreted model in terms of true resistivities against depth within the ice sheet. The extremely low values of resistivity below the ice shelf indicate that it is afloat on sea water. Model resistivities are given in units of 10 kQ m. From Reynolds and Paren (1984), by permission
-'-7~':.=5_ ___=5c....1'-J3u...10",.-,,-0,,-00,-,0--,3-->\
41,1L...6_.o--'I_ _5_.2:.-_--L 14.1
•
10 ' - - ' - - ' - - - - '_ _-'-_L--'-L-_--'-_ _-'-_L..-..L.....J 200 400 1000 6 .0 60 100 20 '0 a (m)
W
0
RJ
-
~ -.:..~~-
.:.;
~-..--
-- - - - ---
RI(
-----_.-
1