An Introduction to The Finite Element Method

Citation preview

SOLUTIONS MANUAL for

An Introduction to The Finite Element Method (Third Edition) by J. N. REDDY Department of Mechanical Engineering Texas A & M University College Station, Texas 77843-3123

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGraw-Hill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

McGraw-Hill, New York, 2005

ii

iii

PREFACE This solution manual is prepared to aid the instructor in discussing the solutions to assigned problems in Chapters 1 through 14 from the book, An Introduction to the Finite Element Method, Third Edition, McGraw—Hill, New York, 2006. Computer solutions to certain problems of Chapter 8 (see Chapter 13 problems) are also included at the end of Chapter 8. The instructor should make an effort to review the problems before assigning them. This allows the instructor to make comments and suggestions on the approach to be taken and nature of the answers expected. The instructor may wish to generate additional problems from those given in this book, especially when taught time and again from the same book. Suggestions for new problems are also included at pertinent places in this manual. Additional examples and problems can be found in the following books of the author: 1. J. N. Reddy and M. L. Rasmussen, Advanced Engineering Analysis, John Wiley, New York, 1982; reprinted and marketed currently by Krieger Publishing Company, Melbourne, Florida, 1990 (see Section 3.6). 2. J. N. Reddy, Energy and Variational Methods in Applied Mechanics, John Wiley, New York, 1984 (see Chapters 2 and 3). 3. J. N. Reddy, Applied Functional Analysis and Variational Methods in Engineering, McGraw-Hill, New York, 1986; reprinted and marketed currently by Krieger Publishing Company, Melbourne, Florida, 1991 (see Chapters 4, 6 and 7). 4. J. N. Reddy, Theory and Analysis of Elastic Plates, Taylor and Francis, Philadelphia, 1997. 5. J. N. Reddy, Energy Principles and Variational Methods in Applied Mechanics, Second Edition, John Wiley, New York, 2002 (see Chapters 4 through 7 and Chapter 10). 6. J. N. Reddy, Mechanics of Laminated Composite Plates and Shells: Theory and Analysis, CRC Press, Second Edition, Boca Raton, FL, 2004. 7. J. N. Reddy, An Introduction to Nonlinear Finite Element Analysis, Oxford University Press, Oxford, UK, 2004.

The computer problems FEM1D and FEM2D can be readily modified to solve new types of field problems. The programs can be easily extended to finite element models formulated in an advanced course and/or in research. The Fortran sources of FEM1D and FEM2D are available from the author for a price of $200. The author appreciates receiving comments on the book and a list of errors found in the book and this solutions manual. J. N. Reddy All that is not given is lost.

iv

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

1

Chapter 1 INTRODUCTION

Problem 1.1: Newton’s second law can be expressed as F = ma

(1)

where F is the net force acting on the body, m mass of the body, and a the acceleration of the body in the direction of the net force. Use Eq. (1) to determine the mathematical model, i.e., governing equation of a free-falling body. Consider only the forces due to gravity and the air resistance. Assume that the air resistance is linearly proportional to the velocity of the falling body. Fd = cv

Fg = mg

v

Solution: From the free-body-diagram it follows that m

dv = Fg − Fd , dt

Fg = mg,

Fd = cv

where v is the downward velocity (m/s) of the body, Fg is the downward force (N or kg m/s2 ) due to gravity, Fd is the upward drag force, m is the mass (kg) of the body, g the acceleration (m/s2 ) due to gravity, and c is the proportionality constant (drag coefficient, kg/s). The equation of motion is dv + αv = g, dt

PROPRIETARY MATERIAL.

α=

c m

c The McGraw-Hill Companies, Inc. °

All rights reserved.

2

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 1.2: A cylindrical storage tank of diameter D contains a liquid at depth (or head) h(x, t). Liquid is supplied to the tank at a rate of qi (m3 /day) and drained at a rate of q0 (m3 /day). Use the principle of conservation of mass to arrive at the governing equation of the flow problem. Solution: The conservation of mass requires time rate of change in mass = mass inflow - mass outflow The above equation for the problem at hand becomes d (ρAh) = ρqi − ρq0 dt

or

d(Ah) = qi − q0 dt

where A is the area of cross section of the tank (A = πD2 /4) and ρ is the mass density of the liquid. Problem 1.3: Consider the simple pendulum of Example 1.3.1. Write a computer program to numerically solve the nonlinear equation (1.2.3) using the Euler method. Tabulate the numerical results for two different time steps ∆t = 0.05 and ∆t = 0.025 along with the exact linear solution. Solution: In order to use the finite difference scheme of Eq. (1.3.3), we rewrite (1.2.3) as a pair of first-order equations dθ = v, dt

dv = −λ2 sin θ dt

Applying the scheme of Eq. (1.3.3) to the two equations at hand, we obtain θi+1 = θi + ∆t vi ;

vi+1 = vi − ∆t λ2 sin θi

The above equations can be programmed to solve for (θi , vi ). Table P1.3 contains representative numerical results. Problem 1.4: An improvement of Euler’s method is provided by Heun’s method, which uses the average of the derivatives at the two ends of the interval to estimate the slope. Applied to the equation du = f (t, u) dt

(1)

Heun’s scheme has the form ui+1 = ui +

i ∆t h f (ti , ui ) + f (ti+1 , u0i+1 ) , u0i+1 = ui + ∆t f (ti , ui ) 2

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(2)

SOLUTIONS MANUAL

3

Table P1.3: Comparison of various approximate solutions of the equation (d2 θ/dt2 ) + λ2 sin θ = 0 with its exact linear solution. Exact t 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.60 0.80 1.00

θ 0.78540 0.76965 0.72302 0.64739 0.54578 0.42229 0.28185 0.13011 -0.02685 -0.18274 -0.33129 -0.58310 -0.78356 -0.50591

Approx. solution θ ∆t = .05

∆t = .025

0.78540 0.78540 0.75694 0.70002 0.58980 0.50496 0.37123 0.21803 0.05023 -0.12628 -0.30481 -0.63965 -1.05068 -0.94062

0.78540 0.77828 0.74276 0.67944 0.56482 0.47627 0.34225 0.19218 0.03148 -0.13374 -0.29690 -0.59131 -0.91171 -0.74672

Exact

Approx. solution v

v -0.00000 -0.62801 -1.23083 -1.78428 -2.26615 -2.65711 -2.94148 -3.10785 -3.14955 -3.06491 -2.85732 -2.11119 0.21536 2.41051

∆t = .05 -0.00000 -0.56922 -1.13844 -1.69123 -2.20984 -2.67459 -3.06403 -3.35605 -3.53018 -3.57060 -3.46921 -2.85712 -0.50399 2.29398

∆t = .025 -0.00000 -0.56922 -1.13027 -1.66622 -2.15879 -2.58816 -2.93371 -3.17573 -3.29791 -3.29007 -3.15014 -2.50787 -0.28356 2.19765

In books on numerical analysis, the second equation in (2) is called the predictor equation and the first equation is called the corrector equation. Apply Heun’s method to Eqs. (1.3.4) and obtain the numerical solution for ∆t = 0.05. Solution: Heun’s method applied to the pair dθ = v, dt

dv = −λ2 sin θ dt

yields the following discrete equations: 0 = θi + ∆t vi θi+1 ´ ∆t ³ 0 vi+1 = vi − λ2 sin θi + sin θi+1 2 ∆t (vi + vi+1 ) θi+1 = θi + 2

The numereical results obtained with the Heun’s method and Euler’s method are presented in Table P1.4.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

4

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Table P1.4: Numerical solutions of the nonlinear equation d2 θ/dt2 + λ2 sin θ = 0 along with the exact solution of the linear equation d2 θ/dt2 +λ2 θ = 0. Exact

Approx. solution θ

Exact

Approx. solution v

t

θ

Euler’s

Heun’s

v

Euler’s

Heun’s

0.00 0.05 0.10 0.20 0.40 0.60 0.80 1.00

0.785398 0.769645 0.723017 0.545784 -0.026852 -0.583104 -0.783562 -0.505912

0.785398 0.785398 0.756937 0.615453 0.050228 -0.639652 -1.050679 -0.940622

0.785398 0.771168 0.728680 0.564818 0.015246 -0.544352 -0.787095 -0.587339

-0.000000 -0.628013 -1.230833 -2.266146 -3.149552 -2.111190 0.215362 2.410506

-0.000000 -0.569221 -1.138442 -2.209838 -3.530178 -2.857121 -0.503993 2.293983

-0.000000 -0.569221 -1.121957 -1.121957 -3.073095 -2.194398 -0.114453 2.023807

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGraw-Hill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

c The McGraw-Hill Companies, Inc. All rights reserved. PROPRIETARY MATERIAL. °

SOLUTIONS MANUAL

5

Chapter 2 MATHEMATICAL PRELIMINARIES, INTEGRAL FORMULATIONS, AND VARIATIONAL METHODS In Problem 2.1—2.5, construct the weak form and, whenever possible, quadratic functionals. Problem 2.1: A nonlinear equation: µ

¶

d du − u + f = 0 for 0 < x < L dx dx ¶¯

µ

√ du ¯¯ u = 0 u(1) = 2 dx ¯x=0

Solution: Following the three-step procedure, we write the weak form: Z 1 ∙

¸

d du v − (u ) + f dx 0= dx dx 0 ¸ ∙ ¸ Z 1∙ dv du du 1 + vf dx − v(u ) u = dx dx dx 0 0

(1) (2)

Using the boundary conditions, v(1) = 0 (because u is specified at x = 1) and (du/dx) = 0 at x = 0, we obtain 0=

Z 1∙ dv du

u

0

dx dx

¸

+ vf dx

(3)

For this problem, the weak form does not contain an expression that is linear in both u and v; the expression is linear in v but not linear in u. Therefore, a quadratic functional does not exist for this case. The expressions for B(·, ·) and `(·) are given by B(v, u) =

Z 1 dv du

u

0

`(v) = −

dx dx

Z 1

dx (not linear in u and not symmetric in u and v)

vf dx

(4)

0

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

6

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

♠ New Problem 2.1: The instructor may assign the following problem: −

∙

¸

du d (1 + 2x2 ) + u = x2 dx dx u(0) = 1 ,

µ

du dx

¶

(1a)

=2

(1b)

x=1

The answer is Z 1∙

B(v, u) =

0

Z 1

`(v) =

¸

dv du + vu dx (symmetric) (1 + 2x ) dx dx 2

v x2 dx + 6v(1)

(2)

0

1 1 I(u) = B(u, u) − `(u) = 2 2

Z 1 0

"

µ

du (1 + 2x ) dx

−

2

Z 1 0

¶2

#

+ u2 dx

u x2 dx − 6u(1)

Problem 2.2: The Euler-Bernoulli-von K´ arm´ an nonlinear beam theory [7]: (

d − dx d2 dx2

Ã

"

du 1 + EA dx 2

µ

!

(

d2 w EI 2 dx

d − dx

u = w = 0 at x = 0, L;

dw dx

¶2 #)

=f

"

for 0 < x < L

dw du 1 + EA dx dx 2

µ

¶¯

dw ¯¯ = 0; dx ¯x=0

µ

dw dx

¶2 #)

Ã

d2 w EI 2 dx

=q

!¯ ¯ ¯ ¯

= M0

x=L

where EA, EI, f , and q are functions of x, and M0 is a constant. Here u denotes the axial displacement and w the transverse deflection of the beam. Solution: The first step of the formulation is to multiply each equation with a weight function, say v1 for the first equation and v2 for the second equation, and integrate over the interval (0, L). In the second step, carry out the integration-by-parts once in the first equation, twice in the first term of the second equation, and once in the second part of the second equation. Then use the fact that v1 (0) = v1 (L) = 0 (because u is specified there), v2 (0) = v2 (L) = 0 (because w is specified), and (dv2 /dx)(0) = 0 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

7

(because dw/dx is specified at x = 0). In addition, we have EI(d2 w/dx2 ) = M0 at x = L. The final weak forms are given by 0= 0=

Z L(

"

µ

¶2 #

)

0

dv1 du 1 + EA dx dx 2

0

d2 v2 d2 w dv2 dw du 1 + EI 2 + EA 2 dx dx dx dx dx 2

Z L(

dw dx

− v1 f dx "

¶ ¯¯ ¯ ¯ M0 ¯

µ

dv2 − dx

µ

(1a) dw dx

¶2 #

)

− v2 q dx (1b)

L

Note that for this case the weak form is not linear in u or w. However, a functional can be constructed for this using the potential operator theory (see: J. T. Oden and J. N. Reddy, Variational Methods in Theoretical Mechanics, 2nd ed., Springer-Verlag, Berlin, 1983 and Reddy [3]). The functional is given by Π(u, w) =

"µ ¶ Z L( EA du 2

2

0

dx )

du + dx

¯

µ

dw dx

dw ¯¯ + uf + wq dx − ¯ M0 dx ¯L

¶2

1 + 2

µ

dw dx

¶4 #

EI + 2

Ã

d2 w dx2

!2

Problem 2.3: A second-order equation: µ

¶

µ

¶

∂u ∂u ∂u ∂u ∂ ∂ + a12 + a22 − a11 − a21 + f = 0 in Ω ∂x ∂x ∂y ∂y ∂x ∂y u = u0 on Γ1 ,

µ

¶

µ

¶

∂u ∂u ∂u ∂u + a12 + a22 a11 nx + a21 ny = t0 on Γ2 ∂x ∂y ∂x ∂y

where aij = aji (i, j = 1, 2) and f are given functions of position (x, y) in a twodimensional domain Ω, and u0 and t0 are known functions on portions Γ1 and Γ2 of the boundary Γ: Γ1 + Γ2 = Γ. Solution: Multiplying with the weight function v and integrating by parts, we obtain the weak Z ∙

µ

Z

vt0 ds

¶

µ

¶

¸

∂v ∂u ∂u ∂u ∂u ∂v + a12 + a22 a11 + a21 + vf dxdy 0= ∂x ∂y ∂y ∂x ∂y Ω ∂x ∙µ ¶ µ ¶ ¸ I ∂u ∂u ∂u ∂u + a12 + a22 − v a11 nx + a21 ny ds ∂x ∂y ∂x ∂y Γ µ ¶ µ ¶ ¸ Z ∙ ∂v ∂u ∂u ∂u ∂u ∂v + a12 + a22 a11 + a21 + vf dxdy = ∂x ∂y ∂y ∂x ∂y Ω ∂x −

Γ2

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

8

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

where v = 0 on Γ1 . The bilinear form (symmetric only if a12 = a21 ) and linear form are: B(v, u) =

Z µ Ω

`(v) = −

Z

¶

∂v ∂u ∂v ∂u ∂v ∂u ∂v ∂u + a12 + a21 + a22 a11 dxdy ∂x ∂x ∂x ∂y ∂y ∂x ∂y ∂y vf dxdy +

Ω

Z

v t0 ds

Γ2

The quadratic functional, when a12 = a21 , is given by 1 I(u) = 2 −

Z " Ω

Z

a11

µ

∂u ∂x

¶2

uf dxdy +

Ω

Z

µ

∂u ∂u ∂u + a22 + 2a12 ∂x ∂y ∂y

Γ2

¶2 #

dxdy

u t0 ds

Problem 2.4: Navier-Stokes equations for two-dimensional flow of viscous, incompressible fluids: !⎫ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ Ã !⎪ ⎬ 2 2 ∂v 1 ∂P ∂ v ∂ v ∂v +v =− +ν u + ⎪ ∂x ∂y ρ ∂y ∂x2 ∂y2 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ∂u ∂v ⎪ ⎪ ⎭ + =0

∂u 1 ∂P ∂u +v =− +ν u ∂x ∂y ρ ∂x

∂x

Ã

∂2u ∂2u + ∂x2 ∂y 2

in Ω

∂y

u = u0 , µ

v = v0

on Γ1

(2)

¶

∂u ∂u 1 nx + ny − P nx = tˆx ) ∂x ∂y ρ µ ¶ on Γ2 ∂v ∂v 1 nx + ny − P ny = tˆy ν ∂x ∂y ρ

ν

(1)

(3)

Solution: For this set of three differential equations in two dimensions (see Chapter 10 and Reddy [7] for the physics behind the equations), we follow exactly the same procedure as before: use the three-step procedure for each equation. In the second step of the formulation, we must integrate by parts the terms involving P , u, and v, because these terms are required as a part of the natural boundary conditions given in Eq. (3). We do not integrate by parts the nonlinear terms in the first two equations, and no integration by parts is used in the third equation, because the boundary terms resulting from such integration-by-parts do not constitute physical PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

9

variables. We have 0=

Z ∙

w1

Ω

−

0=

Z ∙

0=

−

Ω

Z

∂v ∂v +v u ∂x ∂y

µ

µ

∂w1 ∂u ∂w1 ∂u + ∂x ∂x ∂y ∂y

¶¸

dxdy

µ

∂w2 ∂v ∂w2 ∂v + ∂x ∂x ∂y ∂y

¶¸

dxdy

w1 tˆx ds

µ

Γ2

w3

¶

∂u ∂u 1 ∂w1 +v P +ν u − ∂x ∂y ρ ∂x

Γ2

w2

Ω

Z

Z

µ

¶

1 ∂w2 P +ν − ρ ∂y

w2 tˆy ds ¶

∂u ∂v + dxdy ∂x ∂y

where (w1 , w2 , w3 ) are weight functions. Problem 2.5: Two-dimensional flow of viscous, incompressible fluids (stream function-vorticity formulation): ⎫

−∇2 ψ − ζ = 0 ⎪ ⎬ ∂ψ ∂ζ ∂ψ ∂ζ − = 0⎪ −∇2 ζ + ⎭ ∂x ∂y ∂y ∂x

in Ω

Assume that all essential boundary conditions are specified to be zero. Solution: First, we note the the identity −w∇2 ψ = −w∇ · ∇ψ = −∇ · (w∇ψ) + ∇w · ∇ψ and then use the Green—Gauss theorem to obtain −

Z

2

w∇ ψ dxdy =

Ω

Z

[−∇ · (w∇ψ) + ∇w · ∇ψ] dxdy

ΩI

=−

Γ

wˆ n · ∇ψ ds +

Z

Ω

∇w · ∇ψ dxdy

Multiplying the first equation with w1 and the second equation with w2 and integrating over the domain Ω and using the above identity we obtain (the boundary integrals vanish because w1 = 0 and w2 = 0 on the boundary Γ) 0= 0=

Z

(∇w1 · ∇ψ − w1 ζ) dxdy

Ω Z ∙ Ω

∇w2 · ∇ζ + w2

PROPRIETARY MATERIAL.

µ

∂ψ ∂ζ ∂ψ ∂ζ − ∂x ∂y ∂y ∂x

(1) ¶¸

c The McGraw-Hill Companies, Inc. °

dxdy

All rights reserved.

(2)

10

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 2.6: Compute the coefficient matrix and the right-hand side of the N parameter Ritz approximation of the equation ∙

¸

d du − (1 + x) = 0 for 0 < x < 1 dx dx u(0) = 0,

u(1) = 1

Use algebraic polynomials for the approximation functions. Specialize your result for N = 2 and compute the Ritz coefficients. Solution: The weak form for this problem is given by 0=

Z 1

(1 + x)

0

dv du dx dx dx

The variational problem is given by Eqs. (2.5.4a) and (2.5.4b), where [`(φi ) = 0 because there is no source term], Z 1

dφi dφj dx dx dx 0 Z 1 dφi dφ0 dx (1 + x) Fi = −B(φi , φ0 ) = − dx dx 0

Bij = B(φi , φj ) =

(1 + x)

(1a) (1b)

The approximation functions φ0 and φi should be chosen such that φ0 (0) = 0, φ0 (1) = 1 ; φi (0) = φi (1) = 0, (i = 1, 2, ..., n)

(2)

The following algebraic polynomials satisfy the above requirements: φ0 = x , φi = xi (1 − x)

(3)

Substitution of Eq.(3) into Eqs.(1a,b) and evaluating the integrals, we obtain ij + i + j 1 − ij (i + 1)(j + 1) ij − + + i+j−1 i+j i+j+1 i+j+2 1 Fi = (1 + i)(2 + i)

Bij =

For the two-parameter (N = 2) case, we have B11 =

1 17 7 1 1 , B12 = B21 = , B22 = , F1 = , F2 = 2 60 30 6 12

and the parameters c1 and c2 are given by c1 = PROPRIETARY MATERIAL.

55 20 , c2 = − 131 131

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(4a) (4b)

SOLUTIONS MANUAL

11

The two-parameter Ritz solution becomes u(x) = φ0 + c1 φ1 + c2 φ2 55 20 2 (x − x2 ) − (x − x3 ) =x+ 131 131 1 (186x − 75x2 + 20x3 ) = 131 The exact solution is given by uexact =

log (1 + x) log 2

Problem 2.7: Use trigonometric functions for the two-parameter approximation of the equation in Problem 2.6, and obtain the Ritz coefficients. Solution: The following trigonometric functions satisfy the requirements in Eq.(2) of Problem 2.6: πx φ0 = sin , φi = sin iπx 2 For two-parameter case, we have Z 1

Z

1 dφ1 dφ1 dx = π 2 (1 + x) (1 + x) cos πx cos πx dx B11 = dx dx 0 0 Z 1 Z 1 dφ1 dφ2 dx = 2π 2 (1 + x) (1 + x) cos πx cos 2πx dx = B21 B12 = dx dx 0 0 Z 1 Z 1 dφ2 dφ2 dx = 4π 2 B22 = (1 + x) (1 + x) cos 2πx cos 2πx dx dx dx 0 0 Z 1 Z π2 1 dφ1 dφ0 πx dx = − dx F1 = − (1 + x) (1 + x) cos πx cos dx dx 2 0 2 0 Z 1 Z 1 dφ2 dφ0 πx F2 = − dx = −π 2 dx (1 + x) (1 + x) cos 2πx cos dx dx 2 0 0

Using the following trigonometric identities, 1 cos mπx cos nπx = [cos(m + n)πx + cos(m − n)πx] 2 1 2 cos mπx = (1 + cos 2mπx) 2 we obtain

"

3π 2 4 − 20 9

− 20 9 3π 2

PROPRIETARY MATERIAL.

#½

c1 c2

¾

=

½

− 19 (6π − 10) 68 4π 225 + 15

c The McGraw-Hill Companies, Inc. °

¾ All rights reserved.

12

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

and the solution is πx 2 πx = −0.12407 sin πx + 0.02919 sin 2πx + sin 2

U2 (x) = c1 sin πx + c2 sin 2πx + sin

Problem 2.8 A steel rod of diameter d = 2 cm, length L = 25 cm, and thermal conductivity k = 50 W/(m ◦ C) is exposed to ambient air T∞ = 20◦ C with a heat-transfer coefficient β = 64 W/(m2 ◦ C). Given that the left end of the rod is maintained at a temperature of T0 = 120◦ C and the other end is exposed to the ambient temperature, determine the temperature distribution in the rod using a two-parameter Ritz approximation with polynomial approximation functions. The equation governing the problem is given by −

d2 θ + cθ = 0 for 0 < x < 25 cm dx2

where θ = T − T∞ , T is the temperature, and c is given by βP βπD 4β = 1 = 256 m2 = 2 Ak kD πD k 4

c=

P being the perimeter and A the cross sectional area of the rod. The boundary conditions are µ

◦

θ(0) = T (0) − T∞ = 100 C,

¶¯

¯ dθ + βθ ¯¯ k =0 dx x=L

Solution: The weak form of the equation is given by 0=

Z Lµ dv dθ

dx dx

0

¶

+ cvθ dx + cˆv(L)θ(L)

(1)

where cˆ = ( βk ). We have Z Lµ dφi dφj

¶

+ cφi φj dx + cˆφi (L)φj (L) dx dx µ ¶ Z L dφi dφ0 Fi = −B(φi , φ0 ) = − + cφi φ0 dx − cˆφi (L)φ0 (L) dx dx 0

Bij = B(φi , φj ) =

0

We choose the following functions φ0 = θ(0) = 100 , φi = xi PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(2a) (2b)

SOLUTIONS MANUAL

13

From the values of the parameters given, we compute: L = 0.25m, c = 256, and cˆ = ( βk ) = 64/50. The coefficients are evaluated to be B11 =

499 133 91 424 , B12 = B21 = , B22 = , F1 = −832 , F2 = − 300 400 1200 3

or

⎡ 499 ⎣

⎫ ⎤⎧ ⎫ ⎧ ⎨ c1 ⎬ ⎨ −832 ⎬ ⎦ = ⎩ ⎭ ⎩ 424 ⎭ 91 c −

300

133 400

133 400

1200

The solution of these equations is

2

3

c1 = −1, 033.3859 , c2 = 2, 667.2635 The two-parameter Ritz solution is given by θ(x) = 100 − 1033.3859x + 2667.2635x2 θ(0.125) = 12.503◦ C , θ(0.25) = 8.3575◦ C Problem 2.9: Set up the equations for the N-parameter Ritz approximation of the following equations associated with a simply supported beam and subjected to a uniform transverse load q = q0 : d2 dx2

Ã

d2 w EI 2 dx

w = EI

!

= q0

for 0 < x < L

d2 w = 0 at x = 0, L dx2

(a) Use algebraic polynomials. (b) Use trigonometric functions. Compare the two-parameter Ritz solutions with the exact solution. Solution: (a) Choose φ0 = 0 and φi = xi (L − x), which satisfy the geometric conditions w(0) = w(L) = 0. The coefficients are given by i+j−1

Bij = EI ij(L) Fi =

q0 (L)i+2 (1 + i)(2 + i)

∙

(i − 1)(j − 1) 2(ij − 1) (i + 1)(j + 1) − + i+j −3 i+j−2 i+j −1

¸

Note that the expression given above for Bij is not valid when i = 1 and j = 1, 2, · · · , N ; we have, B11 = 4EIL, PROPRIETARY MATERIAL.

B1j = Bj1 = 2EILj , (j > 1)

c The McGraw-Hill Companies, Inc. °

All rights reserved.

14

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

For N = 1 the Ritz coefficient is given by c1 = F1 /B11 = q0 L2 /24EI; and for N = 2, the coefficients are: c1 = q0 L2 /(24EI) , c2 = 0. Hence, the one-parameter and two-parameter solution is the same W1 = W2 (x) = c1 φ1 =

q0 L4 x x q0 L2 x(L − x) = (1 − ) 24EI 24EI L L

(b) Choose φ0 = 0 and φi = sin iπx L . The coefficients are given by µ

¶

EIL iπ 4 for i = j ; Bij = 0 for i 6= j 2 L 2q0 L if i is odd ; Fi = 0 if i is even Fi = iπ

Bij =

Hence, ci =

Fi 4q0 = Bii EIL

µ

L iπ

¶5

=

4q0 L4 EI

µ

1 iπ

¶5

Hence, the solution becomes w2 (x) = c1 φ1 + c3 φ3 =

4q0 L4 4q0 L4 πx 3πx + sin sin EIπ 5 L 243EIπ 5 L

Problem 2.10: Repeat Problem 2.9 for q = q0 sin(πx/L). Solution: (a) We have (a = π/L), Fi =

Z L 0

(q0 sin ax) xi (L − x) dx "

Li i = q0 L + a a − q0

"

Z L

i−1

x

cos ax dx

0

Li+1 i + 1 + − a a

#

Z L

i

#

x cos ax dx

0

For N = 1 we have F1 = 4q0 L3 /π 3 , and c1 = q0 L2 /(EIπ 3 ). For N = 2 the coefficients are F2 = F1 L = 4q0 L3 /π 3 and the solution is c1 = c2 L = 2q0 L2 /(3EIπ 3 ). (b) Choose φ0 = 0 and φi = sin iπx L . The coefficients Bij are the same as in Problem 6 1. The Ritz 2.9(b). The coefficients Fi are given by F1 = f0 L/2 and Fi = 0 for i = coefficients are given by c1 = PROPRIETARY MATERIAL.

q0 L4 , ci = 0 if i 6= 1 EIπ 4

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

15

The Ritz solution coincides with the exact solution, w=

q0 L4 πx sin 4 EIπ L

Problem 2.11: Repeat Problem 2.9 for q = Q0 δ(x − 12 L), where δ(x) is the Dirac delta function (i.e., a point load Q0 is applied at the center of the beam). Solution: The coefficients Fi are given by µ ¶i+1

L 2 (b) Fi = Q0 (−1)i−1 for i odd, and Fi = 0 for i even (a) Fi = Q0

Note that c2 = 0 in both cases. Problem 2.12: Develop the N -parameter Ritz solution for a simply supported beam under uniform transverse load using Timoshenko beam theory. The governing equations are given in Eqs. (2.4.32a, b). Use Trigonometric functions to approximate w and Ψ. Solution: Assume solution of (w, Ψ) in the form, wM =

M X

j=1

bj φj ≡

M X

bj sin

j=1

N N X X jπx jπx , ΨN = cj ψj ≡ cj cos L L j=1 j=1

(1)

Substitution of Eq. (1) into the weak forms (S = GAK and D = EI) Z L∙

µ

¶

¸

dv1 dw + Ψ + kv1 w − v1 q dx GAK 0= dx dx 0 ∙ µ ¶¸ Z L dw dv2 dΨ + GAK v2 + Ψ dx EI 0= dx dx dx 0

(2a) (2b)

we obtain following system of algebraic equations, ∙

[K 11 ] [K 12 ] [K 21 ] [K 22 ]

¸½

{b} {c}

¾

=

½

{F 1 } {F 2 }

¾

(3)

where 11 Kij

21 Kij =

=

Z Lµ 0

Z L 0

¶

dφi dφj 12 + kφi φj dx , Kij GAK = dx dx

GAKψi

dφj 22 dx , Kij = dx

PROPRIETARY MATERIAL.

Z Lµ

EI

0

Z L

GAK

0

dφi ψj dx , dx ¶

dψi dψj + GAK ψi ψj dx dx dx

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(4a)

16

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Fi1 =

Z L 0

φi q dx , Fi2 = 0

(4b)

Substituting φi = sin(iπx/L) and ψi = cos(iπx/L) into the above equations and evaluating the integrals, we obtain 11 = GAK Kij

L 2

µ

iπ L

¶µ

jπ L

¶

+

kL L 12 , Kij = GAK 2 2

∙

L GAK + EI 2

22 Kij =

µ

iπ L

¶µ

jπ L

¶¸

µ

iπ L

¶

21 = Kji ,

(5a)

for i = j, and αβ =0, Kij

Fi1 = −

if i 6= j

(5b)

2q0 L for i = odd and Fi1 = 0 for i = even iπ

(5c)

♠ New Problem 2.2: A number of other problems associated with the Timoshenko beam theory. (1) The same problem as above, with algebraic polynomials; (2) a cantilever beam, clamped at the left end (x = 0) and subjected to an end moment, M0 at x = L. The latter can be assigned with (a) algebraic or (b) trigonometric approximation functions. For example, for Problem 2a, we have the following (M, N )-parameter Ritz solution with algebraic polynomials, wM =

M X

j=1

bj φj ≡

M X

j=1

bj xj , ΨN =

N X

j=1

cj ψj ≡

N X

cj xj

(1)

j=1

The matrix equations are of the form as given in Eq.(3) of Problem 2.12, and the coefficient matrices are the same as given in Eq. (4a) of Problem 2.12, with the following definition of the right-hand vectors, Fi1

=

Z L 0

φi q0 dx , Fi2 = −M0 ψi (L)

(2)

For the choice of approximation functions, φi = ψi = xi , the coefficients can be evaluated as, ij i 12 (L)i+j−1 , Kij (L)i+j = GAK i+j −1 i+j j q0 (L)i+j , Fi1 = (L)i+1 , Fi2 = −M0 (L)i = GAK i+j i+1 ij 1 (L)i+j−1 + GAK (L)i+j+1 = EI i+j−1 i+j+1

11 Kij = GAK 21 Kij 22 Kij

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(3)

SOLUTIONS MANUAL

17

For M = N = 1, we have µ

¶

3EI q0 L3 M0 L b1 = +1 + 2 6CEI GAKL 2CEI Ã ! Ã ! 2 q0 L 1 GAK L2 c1 = − + M0 , C = 1 + − CEI 4 EI 12

(4)

For M = 2 and N = 1, we obtain q0 L 1 , c1 = − b1 = GAK CEI q0 L2 b2 = − 12EI

µ

6EI 1− GAKL2

Ã

¶

q0 L2 + M0 6

!

(5)

M0 + 2EI

Note that the Timoshenko beam theory does not behave well for M = N = 1 due to numerical locking. However, it behaves well when the number of terms are increased. One can use one more term for w than for Ψ (i.e., M = N + 1). Indeed, for M = 4 and N = 3, one obtains the exact solution, q0 x2 M0 x2 q0 x (6L2 − 4Lx + x2 ) + (2L − x) + 24EI 2GAK 2EI q0 x x M 0 Ψ(x) = (−3L2 + 3Lx − x2 ) − 6EI EI w(x) =

(6)

Problem 2.13: Solve the Poisson equation governing heat conduction in a square region: −k∇2 T = g0 T = 0 on sides x = 1 and y = 1

(1)

∂T = 0 (insulated) on sides x = 0 and y = 0 ∂n

(2)

using a one-parameter Ritz approximation of the form T1 (x, y) = c1 (1 − x2 )(1 − y2 )

(3)

Solution: The weak form of the equation is given by 0=

Z 1Z 1∙ µ ∂v ∂T 0

0

PROPRIETARY MATERIAL.

∂v ∂T + k ∂x ∂x ∂y ∂y

¶

¸

− vg0 dxdy

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(4)

18

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

The coefficients B11 and F1 are given by B11 = =

Z 1Z 1 0

F1 = =

0

0

k 4x2 (1 − y2 )2 + 4y 2 (1 − x2 )2 dxdy =

Z 1Z 1 0

0

Z 1Z 1 0

¶

∂φ1 ∂φ1 ∂φ1 ∂φ1 + k ∂x ∂x ∂y ∂y

Z 1Z 1 0

µ

0

h

dxdy i

64 k 45

(5a)

g0 φ1 dxdy 4 g0 (1 − x2 )(1 − y2 ) dxdy = g0 9

(5b)

and the parameter c1 is given by c1 =

F1 5g0 = B11 16k

(6)

Problem 2.14: Determine φi for a two-parameter Galerkin approximation with algebraic approximation functions for Problem 2.8. Solution: We must choose φ0 such that it satisfies all specified boundary conditions: φ0 (0) = θ(0) ,

∙

dφ0 + cˆφ0 dx

¸

=0

(1)

x=L

and φi must be selected such that it satisfies the homogeneous form of all specified boundary conditions: ∙ ¸ dφi + cˆφi φi (0) = 0 , =0 (2) dx x=L To construct these functions, we begin with φ0 = a + bx, and determine the constants a and b such that φ0 satisfies the conditions in Eq. (1). We obtain, ∙

¸

cˆ φ0 = 100 1 − x 1 + cˆL

Similarly, we begin with φ1 = a + bx + cx2 (we must have one more parameters than the number of conditions) and determine a, b and c such that φ1 satisfies the conditions in Eq. (2). We obtain, ∙

φ1 = x 1 −

1 + cˆL x 2 + cˆL L

¸

The next function should be higher order than φ1 ; and there are two choices: φ2 = a + bx + cx3 and φ2 = a + bx2 + cx3 . For the first choice, we obtain, ∙

φ2 = x 1 − PROPRIETARY MATERIAL.

1 + cˆL x 2 ( ) 3 + cˆL L

¸

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

19

It is clear that the Galerkin and other weighted residual methods involve cumbersome algebra and result in complicated expressions for the approximation functions. Problem 2.15: Consider the (Neumann) boundary value problem − µ

d2 u =f dx2

for 0 < x < L

¶¯

du ¯¯ = dx ¯x=0

µ

¶¯

du ¯¯ =0 dx ¯x=L

Find a two-parameter Galerkin approximation of the problem using trigonometric approximation functions, when (a) f = f0 cos(πx/L) and (b) f = f0 . Solution: For this problem, we can choose φ0 = 0 or a constant (i.e., the solution can be determined only within a constant) and φi = cos iπx/L. The residual is given by N X d2 φj R=− cj 2 − f dx i=1 The weighted-residual statements are given by Z L

Z

L π L πx πx R dx = ( )2 c1 − dx f cos L L 2 L 0 0 Z L Z L 2π L 2πx 2πx 0= R dx = ( )2 c2 − dx cos f cos L L 2 L 0 0

0=

cos

For (a) f = f0 cos πx L , we obtain c1 = c1 = c2 = 0.

f0 L2 π2

and c2 = 0. When (b) f = f0 , we obtain

♠ Part (b) solution indicates that the Neumann problem does not have a solution for the case in which the forcing function is a constant (because the solvability conditions are not satisfied by the data, f ). For additional discussion on this, the reader may consult the book by Reddy [3]. Problem 2.16: Find a one-parameter approximate solution of the nonlinear equation µ

d2 u du −2u 2 + dx dx

¶2

= 4 for 0 < x < 1

subject to the boundary conditions u(0) = 1 and u(1) = 0, and compare it with the exact solution u0 = 1 − x2 . Use (a) the Galerkin method, (b) the least-squares method, and (c) the Petrov—Galerkin method with weight function w = 1. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

20

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Solution: We must choose φ0 such that it satisfies all specified boundary conditions: φ0 (0) = 1 , φ0 (1) = 0

(1)

and φi must be selected such that it satisfies the homogeneous form of all specified boundary conditions: (2) φi (0) = 0 , φi (1) = 0 Obviously, the following choice would meet the requirements, φ0 = 1 − x , φ1 = x(1 − x)

(3)

The residual is given by dφ1 dφ0 2 d2 φ1 + ) −4 + (c1 2 dx dx h i dx = −2 (1 − x) + c1 (x − x2 ) (−2c1 ) + [−1 + c1 (1 − 2x)]2 − 4

R = −2c1 (c1 φ1 + φ0 )

= −3 + 2c1 + (c1 )2

(4)

(a) The weighted-residual statement for the Galerkin method is given by 0=

Z 1 0

(x − x2 )R dx =

i 1h −3 + 2c1 + (c1 )2 6

which gives two solutions, (c1 )1 = 1 and (c1 )2 = −3. We choose c1 = 1 on the basis of R the criterion that 01 R dx is a minimum. For c1 = 1, the Galerkin solution coincides with the exact solution, u(x) = 1 − x2 . (b) The least-squares statement is given by 0=

Z 1 dR 0

dc1

R dx =

Z 1 0

h

i

2(1 + c1 ) −3 + 2c1 + (c1 )2 dx

which gives three solutions, (c1 )1 = 1, (c1 )2 = −3, and (c1 )3 = −1. Once again, we choose c1 = 1. Problem 2.17: Give a one-parameter Galerkin solution of the equation −∇2 u = 1 in Ω (= unit square) u = 0 on Γ Use (a) algebraic and (b) trigonometric approximation functions. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

21

Solution: For this problem, all of the boundary conditions are of the essential type. Hence, the difference between the Ritz and Galerkin methods disappears. In both methods, we must choose φ0 and φi such that φ0 = 0 , φi = 0 on Γ

(1)

We choose the approximation in the form, u1 = c11 sin πx sin πy

(2)

and compute the residual, h

i

R = 2c11 π 2 sin πx sin πy − 1

(3)

The Galerkin integral yields the result, 0= =

Z

R sin πx sin πy dxdy

Ω Z 1Z 1h 0

0

= 2c11 π 2

i

2c11 π 2 sin2 πx sin2 πy − sin πx sin πy dxdy

µ ¶

1 4 − 2 4 π

from which we obtain, c11 =

(4)

8 π4 .

Problem 2.18: Repeat Problem 2.17(a) for an equilateral triangular domain. Hint: Use the product of equations of the lines representing the sides of the triangle for the approximation function. Answer: c1 = − 12 . Solution: For the coordinate system shown in the figure, the equations of the boundary segments AB, BC, and CA are, respectively: x−

√

√ 2 2 1 3y − a = 0 , x + 3y − a = 0 , x + a = 0 3 3 3

Therefore, a suitable choice of φ1 (φ0 = 0) is µ

φ1 = −

¶

a

B a √3

A

a √3

√ √ 2 1 1 2 (x − 3y − a)(x + 3y − a)(x + a) 2a 3 3 3

C

x

a 3

y

because φ1 would be zero on any of the three line segments (i.e. boundary), satisfying the requirement, φ1 = 0 on Γ. The multiplicative constant added in the definition of φ1 is for only normalization purpose. The residual becomes, R = −∇2 u − 1 = −c1 ∇2 φ1 − 1 = −2c1 − 1 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

22

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Since the residual is a constant, the coefficient c1 , in any weighted—residual method is given by c1 = −1/2. Problem 2.19: Consider the differential equation −

d2 u = cos πx for 0 < x < 1 dx2

subject to the following three sets of boundary conditions: (1) u(0) = 0, (2) u(0) = 0, (3)

³

du dx

´ ¯¯ ¯ ¯

x=0

u(1) = 0

´ ¯¯ ¯ =0 ¯ x=1 ¯ ³ ´¯ du ¯ = 0, =0 dx ¯ ³

du dx

x=1

Determine a three-parameter solution, with trigonometric functions, using (a) the Ritz method, (b) the least-squares method, and (c) collocation at x = 14 , 12 , and 34 , and compare with the exact solutions: (1) u0 = π −2 (cos πx + 2x − 1) (2) u0 = π −2 (cos πx − 1) (3) u0 = π −2 cos πx Solution: This problem has three sets of boundary conditions and three different methods are to be used to determine the solution. Hence, it is advised that the instructor should assign only one of the many combinations: (i) Solve the problem for Set 1 boundary conditions with any one of the methods (three problems); (ii) solve Set 2 boundary conditions with any one of the methods (three problems); and (iii) solve Set 3 boundary conditions with any one of the methods (three problems). Solutions for all cases are included here. Set 1: u(0) = u(1) = 0. Ritz method. The bilinear and linear forms are given by B(u, v) =

Z 1 du dv 0

dx dx

dx ,

`(v) =

Z 1

v cos πxdx

0

We use φ0 = 0 and φi = sin iπx. We obtain Bij = Fi =

Z 1

2

(iπ) cos iπx cos jπx dx =

0

(

)

(

)

if j6=i . (iπ)2 , if j=i 2

0,

if i is odd . 2i , if i is even 2 π(i −1)

0,

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

(1) (2)

All rights reserved.

SOLUTIONS MANUAL

23

The solution is given by ci =

1 4 , for i even π 3 i(i2 − 1)

(3)

Weighted-residual methods. The residual is given by R=−

N X ∂R d2 UN − cos πx = cj (jπ)2 sin jπx − cos πx , and = (iπ)2 sin iπx (4) 2 dx ∂c i j=1

The least-squares method requires

0=

Z 1 0

⎛

(iπ)2 sin iπx ⎝

N X

j=1

⎞

cj (jπ)2 sin jπx − cos πx⎠ dx

The multiplicative factor (iπ)2 can be deleted. Then, it is clear that the least squares method and the Galerkin method give the same equations. Furthermore, the solution of the Galerkin and least squares methods would be the same as that of the Ritz method. For the collocation method, we have 3 X π 1 jπ − cos 0 = R(x = ) = cj (jπ)2 sin 4 4 4 j=1 2

= c1 (π)

µ

¶

µ

¶

1 1 1 √ + c2 (2π)2 + c3 (3π)2 √ − √ 2 2 2

3 X π jπ 1 − cos cj (jπ)2 sin 0 = R(x = ) = 2 2 2 j=1

= c1 (π)2 + c2 · 0 − c3 (3π)2 − 0

3 X 3π 3jπ 3 − cos cj (jπ)2 sin 0 = R(x = ) = 4 4 4 j=1

µ

¶

µ

¶

1 1 1 = c1 (π)2 √ − c2 (2π)2 + c3 (3π)2 √ + √ 2 2 2

which gives c1 = c3 = 0 and c2 =

(5)

√ 2/8π 2 .

Set 2: u(0) = du dx (1) = 0. For the Ritz method, we use φ0 = 0, φ1 = x, φ2 = sin πx and φ3 = sin 2πx. This choice makes the variational solution not vanish at x = 1. For convenience, we denote the new set by {φˆ0 = x, φˆ1 = sin πx, φˆ2 = sin 2πx}. For the PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

24

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Ritz method, we need to evaluate only B0j , j = 0, 1, 2 and F0 . All other coefficients are the same as in Eqs.(1) and (2). We have, B00 = 1, B01 = B02 = 0, F0 = −

2 π2

(6)

and the parameters ci , i = 1, 2, 3 are the same as in Eq. (3), and c0 is given by c0 = − π22 . Thus the solution of Set 2 boundary conditions differs from that of Set 1 by the term, (−2x/π 2 ). For the weighted-residual methods, the above set of approximation functions is not admissible, because {φˆ0 = x, φˆ1 = sin πx, φˆ2 = sin 2πx} does not satisfy the natural boundary condition, u(0) = du dx (1) = 0. We select an alternative set, uN =

N X

j=1

cj φj (x) + φ0 = 0 , φ0 = 0 , φj (x) = 1 − cos jπx

(7)

The residual is given by R=−

N X

j=1

cj (jπ)2 cos jπx − cos πx , and

∂R = −(iπ)2 cos iπx ∂ci

(8)

Clearly, weighted-integral statements for the Galerkin and least-squares methods differ by a multiplicative constant (−(iπ)2 ), and hence give the same equations for the undetermined parameters. We obtain, Bij = −

(jπ)2 when i = j ; Bij = 0 when i 6= j 2 F1 =

1 , Fi = 0 when i 6= 1 2

(9)

1 , ci = 0 when i 6= 1 π2

(10)

The solution is given by c1 = −

The variational solution coincides with the exact solution u(x) =

1 (cos πx − 1) π2

The collocation method gives the following algebraic equations 3 X 1 π jπ 0 = R(x = ) = − − cos cj (jπ)2 cos 4 4 4 j=1 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

2

= −c1 (π)

µ

¶

µ

25

¶

1 1 1 √ − c2 · 0 + c3 (3π)2 √ − √ 2 2 2

3 X π jπ 1 − cos cj (jπ)2 cos 0 = R(x = ) = − 2 2 2 j=1

= −c1 · 0 + c2 (2π)2 − c3 · 0 − 0

3 X 3π 3jπ 3 − cos cj (jπ)2 cos 0 = R(x = ) = − 4 4 4 j=1 2

= c1 (π)

µ

¶

µ

which gives c1 = − π12 and c2 = c3 = 0. Set 3:

du dx (0)

=

du dx (1)

uN =

¶

1 1 1 √ − c2 · 0 + c3 (3π)2 √ + √ 2 2 2

(10)

= 0 Here we select the following approximation for all methods,

N X

cj φj (x) + φ0 = 0 , φ0 = 0 , φj (x) = cos jπx

(11)

j=1

The residual is given by R=

N X

j=1

cj (jπ)2 cos jπx − cos πx , and

∂R = (iπ)2 cos iπx ∂ci

(12)

which differs from that given in Eq. (7) by only the sign in front of the parameter, cj . Hence, we expect to obtain the negative of the solution in Eq.(10) in all methods: c1 = π12 and ci = 0 for all i 6= 1. Thus, the variational solutions coincide with the exact solution, cos πx u(x) = π2 Problem 2.20: Consider a cantilever beam of variable flexural rigidity, EI = a0 [2 − (x/L)2 ] and carrying a distributed load, q = q0 [1 − (x/L)]. Find a threeparameter solution using the collocation method. Solution: Let W3 (x) = c1 x2 + c2 x3 + c3 x4 and compute the residual, "

#

µ

d2 x2 d2 w x R = 2 a0 (2 − 2 ) 2 − q0 1 − dx L dx L = a0 = a0 = a0

"

#

¶

µ

2 d2 w x2 d4 w x − 2 2 + (2 − 2 ) 4 − q0 1 − L dx L dx L

"

¶

#

µ

2 x2 x − 2 (2c1 + 6c2 x + 12c3 x2 ) + (2 − 2 )24c3 − q0 1 − L L L

"

#

µ

x2 4 x x 48(1 − 2 )c3 − 2 c1 − 12 2 c2 − q0 1 − L L L L

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

¶

¶

All rights reserved.

26

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

We take the collocation points at x =

L L 4, 2,

µ

4 L R( ) = a0 − 2 c1 − 4 L µ 4 L R( ) = a0 − 2 c1 − 2 L µ 3L 4 R( ) = a0 − 2 c1 − 4 L

and

3L 4

and obtain ¶

3 c2 + 45c3 − L ¶ 6 c2 + 36c3 − L ¶ 9 c2 + 21c3 − L

3 q0 = 0 4 1 q0 = 0 2 1 q0 = 0 4

The solution of these equations is c1 = −

q0 L2 q0 L , c2 = , and c3 = 0 4a0 12a0

Problem 2.21: Consider the problem of finding the fundamental frequency of a circular membrane of radius a, fixed at its edge. The governing equation for axisymmetric vibration is −

µ

¶

1 d du r − λu = 0 0 < r < a r dr dr

where λ is the frequency parameter and u is the deflection of the membrane. (a) Determine the trigonometric approximation functions for the Galerkin method, (b) use one-parameter Galerkin approximation to determine λ, and (c) use two-parameter Galerkin approximation to determine λ. Solution: (a) The approximation functions that satisfy the boundary condition u = 0 at r = a (and du/dr = 0 at r = 0) are φ1 (r) = cos

πr 3πr 5πr , φ2 (r) = cos , φ3 (r) = cos ... 2a 2a 2a

(b) For one-parameter approximation u(r) ≈ U1 (r) = c1 cos(πr/2a), the Galerkin integral is Z a( 0

∙

µ

1 d π πr r − sin r dr 2a 2a

¶¸

πr c1 + λc1 cos 2a

)

cos

πr rdr = 0 2a

from which we obtain π2 4

µ

2 1 + 2 2 π

¶

µ

2 1 − 2 −λ 2 π

¶

=0

It follows that λ = 5.832/a2 . PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

27

(c) For a two-parameter Ritz approximation U2 (r) = c1 cos(πr/2a) + c2 cos(3πr/2a), we obtain (1.7337 − 0.29736λa2 )c1 + (0.20264λa2 − 1.5)c2 = 0 (0.20264λa2 − 1.5)c1 + (11.603 − 0.47748λa2 )c2 = 0

Setting the determinant of the above equations to zero, we obtain a quadratic equation in λ ¯ 2 − 3.6701λ ¯ + 17.866 = 0, λ ¯ = λa2 0.10092λ The smaller root of the equation is λ = 5.792/a2 . The exact value is λ = 5.779/a2 .

Problem 2.22: Find the first two eigenvalues associated with the differential equation d2 u − 2 = λu, 0 < x < 1 dx u(0) = 0, u(1) + u0 (1) = 0 Use the least squares method. Use the operator definition to be A = −(d2 /dx2 ) to avoid increasing the degree of the characteristic polynomial for λ. Solution: For this problem, the choice of the operator A is crucial. If we use the definition A = −d2 /dx2 − λ, we obtain the result 0=

Z 1 0

= =

A(φi )R dx =

"Z Ã n 1 d2 φ X i

dx2 0 j=1 (Z " n 1 d2 φ X i 2 dx 0 j=1

n ∙Z 1 X

j=1

+ λφi

0

!Ã

¸

A(φi )A(φj ) dx cj

d2 φj + λφj dx2

Ã

!

#

dx cj

d2 φj d2 φj d2 φi + λ φ + φj i dx2 dx2 dx2

!

2

+ λ φi φj

#

)

dx cj

(1)

which is a quadratic (matrix) eigenvalue problem, and it is more difficult (but not impossible) to solve. Alternatively, we identify the operator A of the problem to be A = −d2 /dx2 so that it does not include the unknown, λ (not consistent with the definition of the method). Then 0=

Z 1 0

= =

A(φi )R dx =

n ½Z 1 X

j=1

"Z Ã n 1 d2 φ d2 φ X i j

j=1 n X j=1

0

dx2

0

¾

A(φi ) [A(φj ) − λφj ] dx cj

d2 φi + λ φj dx2 dx2

!

#

dx cj

(Kij − λMij ) cj

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

(2a)

All rights reserved.

28

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

where Kij = Mij =

Z 1 0

Z 1 0

A(φi )A(φj ) dx = A(φi )φj dx = −

Z

Z 1 2 d φi d2 φj

0

2 2 0 dx dx 1 d2 φ i φj dx dx2

dx (2b)

Using the approximation functions φ1 = 3x − 2x2 and φ2 = 4x2 − 3x3 , we have A(φ1 ) = 4 and A(φ2 ) = −4 + 12x, and K11 = 16, K12 = K21 = 8, K22 = 16, 10 8 8 38 M11 = , M12 = , M21 = , M22 = 3 3 3 15

(3)

The characteristic polynomial and its roots are 48 −

1 64 λ + λ2 = 0 giving λ1 = 4.212, λ2 = 34.188 5 3

(4)

Problem 2.23: Repeat Problem 2.22 using the Ritz method. Solution: A two-parameter Ritz approximation with φ0 = 0, yields

¯ ¯2− λ 3 ¯ ¯2− λ

(1)

¯

2 − λ4 ¯¯ 7 λ¯=0 3 − 5

4

or

φ2 = x2

φ1 = x,

(2)

15λ2 − 640λ + 2400 = 0 → λ1 = 4.1545,

λ2 = 38.512

(3)

The exact values are λ1 = 4.116,

λ2 = 24.139

(4)

The weighted-residual solutions are more accurate than the Ritz solution because they use higher-order polynomials that satisfy all boundary conditions. Problem 2.24: Consider the Laplace equation −∇2 u = 0,

0 < x < 1,

00

∂u (1, t) = 1, u(x, 0) = x ∂x Use linear rectangular elements in the (x, t)-plane to model the problem. Note that the finite-element model is given by [K e ]{ue } = {Qe }, where u(0, t) = 0,

e Kij

=

Z ∆t Z xb à ∂ψ e ∂ψje

∂ψj + cψi ∂x ∂x ∂t i

0

PROPRIETARY MATERIAL.

xa

!

dx dt

c The McGraw-Hill Companies, Inc. °

All rights reserved.

290

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Qe1

Ã

= −

!¯ ¯ dt ¯¯ , ∂x x=xa

Z ∆t ∂u 0

Qe2

=

ÃZ ∆t ∂u

!¯ ¯ dt ¯¯ ∂x x=xb

0

Solution: For one space-time element mesh, we have the equations ⎡

−2c + 4r ∆x ⎢ ⎢ −c − 4r 12 ⎣ −c − 2r −2c + 2r

−c − 4r −2c + 4r −2c + 2r −c − 2r

c − 2r 2c + 2r 2c + 4r c − 4r

⎤⎧

⎫

⎧

⎫

2c + 2r ⎪ U1 ⎪ ⎪ Q1 ⎪ ⎪ ⎪ ⎪ ⎨ ⎬ ⎪ ⎨ c − 2r ⎥ U Q2 ⎬ 2 ⎥ = c − 4r ⎦ ⎪ ⎪ U3 ⎪ ⎪ ⎪ ⎪ Q3 ⎪ ⎪ ⎩ ⎭ ⎩ ⎭ 2c + 4r U4 Q4

(1)

The “boundary conditions” are: U1 = 0, U2 = ∆x, U4 = 0, Q3 = ∆t. Note that we have no condition given at t = ∆t. This amounts to assuming that ∂u/∂t = 0. The value at the node 3 (i.e., U3 = u(∆x, ∆t)) can be determined easily from Eq. (1), ∆x [(−2c + 2r)U2 + (2c + 4r)U3 ] = Q3 12 or

∙

¸

∆t ∆t + 2c∆x 2c + 4 U3 = 14 2 (∆x) ∆x

For c = c0 r, we have the result, U3 =

14 + 2c0 ∆x 4 + 2c0

The α-family of approximation yields the equation Ã

∙

¸

∙

c∆x 2 1 α∆t 1 −1 + 1 2 6 ∆x −1 1

=

Ã

∙

¸

∙

¸! ½

U1n+1 U2 n+1

c∆x 2 1 (1 − α)∆t 1 −1 − 1 2 −1 1 6 ∆x

¾

¸! ½

U1n U2n

¾

+ ∆t

½

Q1 Q2

¾

Using U1 = 0, Q2 = 1 and U2n+1 = ∆x, we obtain µ

¶

µ

¶

∆t ∆x ∆x ∆t +α +c c U2n+1 = −(1 − α) ∆x + ∆t 3 ∆x ∆x 3

For c = c0 r, we have the result, U3 = ∆x. While the two results differ quite a bit, it should not be taken seriously in view of the coarse mesh taken and the special boundary and initial conditions used. In general, the space-time finite elements have a natural drawback in redefining the initial-boundary value problem as an equivalent boundary value problem. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

291

Problem 8.59: The collocation time approximation methods are defined by the following relations: {¨ u}n+α = (1 − α){¨ u}n + α{¨ u}n+1 {u} ˙ n+α = {u} ˙ n + α∆t[(1 − γ){¨ u}n + γ{¨ u}n+α ] α(∆t)2 [(1 − 2β){¨ u}n + 2β{¨ u}n+α ] 2 The collocation scheme contains two of the well-known schemes: α = 1 gives the Newmark’s scheme; β = 16 and γ = 12 gives the Wilson scheme. The collocation scheme is unconditionally stable, second-order accurate for the following values of the parameters: {u}n+α = {u}n + α∆t{u} ˙ n+

α ≥ 1,

1 γ= , 2

α 2α2 − 1 ≥β≥ 2(1 + α) 4(2α3 − 1)

Formulate the algebraic equations associated with the matrix differential equation [M ]{¨ u} + [C]{u} ˙ + [K]{u} = {F } using the collocation scheme. Solution: Consider the equation [M ]{¨ u} + [C]{u} ˙ + [K]{u} = {F }

(1)

and the equations of the collocation scheme {¨ u}s+α = (1 − α){¨ u}s + α{¨ u}s+1

(2)

˙ s + α∆t [(1 − γ){¨ u}s + γ{¨ u}s+α ] {u} ˙ s+α = {u}

(3)

(∆t)2 [(1 − 2β){¨ u}s + 2β{¨ u}s+α ] (4) 2 Like in Problem 6.23, we formulate the final equation for the acceleration vector. This is done by writing Eq. (1) for t = ts+α and substituting for the acceleration, velocity, and displacement at ts+α from Eqs. (2), (3), and (4), respectively. In using Eqs. (3) and (4), the acceleration at ts+α is replaced by Eq. (2). We obtain ˙ s+α {u}s+α = {u}s + α∆t{u}

ˆ s+α {¨ ˆ ]s+α {¨ ˆ s+α {u} [H] u}s+1 = {Fˆ }s+α − [M u}s − [C] ˙ s − [K]s+α {u}s where ˆ s+α = α ([M ]s+α + c1 [C]s+α + c2 [K]s+α ) [H] ˆ ]s+α = ((1 − α)[M ]s+α + c3 [C]s+α + c4 [K]s+α ) [M PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(5)

292

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

ˆ s+α = [C]s+α + α∆t[K]s+α , {Fˆ }s+α = (1 − α){F }s + α{F }s+1 [C] c1 = αγ∆t, c2 = αβ(∆t)2 , c3 = α(1 − αγ)∆t, (0.5 − αβ)α(∆t)2

(6)

Once the acceleration is known, Eqs. (3) and (4) can be used to compute the velocity and displacement at time ts+1 . Problem 8.60: Consider the following pair of coupled partial differential equations: −

µ

¶

∙ µ

∂ ∂u ∂v ∂u ∂ + a − b ∂x ∂x ∂y ∂y ∂x ∙ µ

∂u ∂v ∂ + b ∂x ∂y ∂x

−

¶¸

µ

¶¸

∂ ∂v c ∂y ∂y

−

¶

+

∂u − fx = 0 ∂t

(1)

+

∂v − fy = 0 ∂t

(2)

where u and v are the dependent variables (unknown functions), a, b and c are known functions of x and y, and fx and fy are known functions of position (x, y) and time t. (a) Use the three-step procedure on each equation with a different weight function for each equation (say, w1 and w2 ) to develop the (semidiscrete) weak form. (b) Assume finite element approximation of (u, v) in the following form u(x, y) =

n X

ψj (x, y)Uj (t) , v(x, y) =

j=1

n X

ψj (x, y)Vj (t)

(3)

j=1

and develop the (semidiscrete) finite element model in the form 0= 0=

n X

j=1 n X

Mij11 U˙ j

+

Mij22 V˙ j +

j=1

n X

11 Kij Uj

+

n X

j=1

j=1

n X

n X

21 Kij Uj +

j=1

j=1

12 Kij Vj − Fi1 22 Kij Vj − Fi2

(4)

11 , K 12 , F 1 etc. You must define the algebraic form of the element coefficients Kij ij i (c) Give the fully discretized finite element model of the model (in the standard form; you are not required to derive it).

Solution: (a) The weak forms are given by Z

½

µ

¶

∙ µ

¶¸

¾

∂u ∂v ∂ ∂u ∂ ∂u + − fx dxdy a − b + e ∂x ∂x ∂y ∂y ∂x ∂t Ω ∙ µ ¶¸ ¾ Z ½ ∂u ∂v ∂u ∂w1 ∂u ∂w1 + + − w1 fx dxdy a b + w1 = ∂x ∂x ∂y ∂y ∂x ∂t Ωe

0=

w1 −

+

I

Γe

w1 tx ds

PROPRIETARY MATERIAL.

(5)

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

½

Z

∙ µ

¶¸

µ

¶

293

¾

∂u ∂v ∂ ∂ ∂v ∂v + − fy dxdy w2 − b − c + 0= ∂x ∂y ∂x ∂y ∂y ∂t Ωe ½ ∙ µ ¶¸ ¾ Z ∂w2 ∂u ∂v ∂v ∂w2 ∂v + + w2 − w2 fy dxdy b +c = ∂x ∂y ∂x ∂y ∂y ∂t Ωe +

I

Γe

w2 ty ds

(6)

where ∙ µ

∂u ∂v ∂u + tx = a nx + b ∂x ∂y ∂x

¶¸

∙ µ

∂u ∂v + ny , ty = b ∂y ∂x

¶¸

nx + c

∂v ny ∂y

(7)

(b) The finite element model is given by Eq. (4) with the following coefficients: Mij11

=

Mij22 =

22 Kij

e

ZΩ

Ωe

ψi ψj dxdy ψi ψj dxdy

Z

µ

¶

Z

fx ψi dxdy +

∂ψi ∂ψj ∂ψi ∂ψj +b dxdy ∂x ∂x ∂y ∂y Ωe Z ∂ψi ∂ψj 21 dxdy = Kji = b e ∂y ∂x Ω ¶ Z µ ∂ψi ∂ψj ∂ψi ∂ψj +c = b dxdy ∂x ∂x ∂y ∂y Ωe

11 = Kij 12 Kij

Z

Fi1 = Fi2 =

a

Ωe

Z

Ωe

fy ψi dxdy +

I

I

Γe

Γe

tx ψi ds ty ψi ds

(8)

(c) The pair of equations in (4) can be written in matrix form as ∙

[M 11 ] [0] [0] [M 22 ]

¸½

{U˙ } {V˙ }

¾

∙

[K 11 ] [K 12 ] + [K 21 ] [K 22 ]

¸½

{U } {V }

¾

=

½

{F 1 } {F 2 }

¾

or ˙ + [K]{∆} = {F } [M ]{∆}

(9)

which is in the standard form of a parabolic equation [see Eq. (8.6.6b)]. Hence, the fully discretized finite element model is given by Eqs. (8.6.10a) and (8.6.10b).

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGrawHill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

Chapter 9 INTERPOLATION FUNCTIONS, NUMERICAL INTEGRATION, AND MODELING CONSIDERATIONS

Problem 9.1: Show that the interpolation functions for the three-node equilateral triangular element given in Fig. P9.1 are ψ1 =

µ

¶

µ

¶

1 1 1 1 1 1 − ξ − √ η , ψ2 = 1 + ξ − √ η , ψ3 = √ η 2 2 3 3 3 η 3

η = 3 (1 + ξ )

η = 3 (1 − ξ ) 3 1

2

1

1

ξ

Figure P9.1 Solution: Since ψ1 must vanish on line connecting nodes 2 and 3, it must be of the form h i √ ψ1 (ξ, η) = c1 η − 3 (1 − ξ) √ Since ψ1 (−1, 0) = 1, we obtain c1 = −1/2 3. Thus, we have µ ¶ h i √ 1 1 ψ1 (ξ, η) = c1 η − 3 (1 − ξ) = 1−ξ− √ η 2 3 h i √ Similarly, ψ2 should be of the form ψ2 (ξ, η) = c2 η − 3 (1 + ξ) and it should be √ equal to unity at node 2, giving c2 = −1/2 3. Hence, we have µ ¶ h i √ 1 1 ψ2 (ξ, η) = c2 η − 3 (1 + ξ) = 1+ξ− √ η 2 3 Finally, we know that ψ3 must vanish on line η = 0. Hence, it is of the form η ψ3 (ξ, η) = c3 η → ψ3 (ξ, η) = √ 3 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

296

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 9.2: Show that the interpolation functions that involve the term ξ 2 + η 2 for the five-node rectangular element shown in Fig. P9.2 are given by ψ1 = 0.25(−ξ − η + ξη) + 0.125(ξ 2 + η 2 )

ψ2 = 0.25(ξ − η − ξη) + 0.125(ξ 2 + η 2 ) ψ3 = 0.25(ξ + η + ξη) + 0.125(ξ 2 + η 2 )

ψ4 = 0.25(−ξ + η − ξη) + 0.125(ξ 2 + η 2 )

ψ5 = 1 − 0.5(ξ 2 + η2 ) η

3

4

2

ξ

5 2

1

2

Figure P9.2 Solution: The interpolation functions are of the form ψi (ξ, η) = ai + bi ξ + ci η + di ξη + ei (ξ 2 + η 2 ) For example, using the interpolation property of ψ1 , we obtain five sets of algebraic relations, which can be expressed in matrix form as ⎡

1 0 0 0 ⎢ 1 −1 −1 1 ⎢ ⎢1 1 −1 −1 ⎢ ⎣1 1 1 1 1 −1 1 −1

⎤⎧

⎫

⎧ ⎫

0 ⎪ a1 ⎪ 0⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ b 2⎥ ⎥⎨ 1 ⎬ ⎨1⎬ ⎥ 2 ⎥ c1 = 0 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪0⎪ ⎪ d ⎪ 2⎦⎪ ⎪ ⎩ 1⎪ ⎭ ⎪ ⎩ ⎪ ⎭ e1 2 0

The determinant of this matrix is 32. Using Cramer’s rule, we can solve the matrix equations for the constants: a1 = 0, b1 = −8/32 = −0.25, c1 = −0.25, d1 = 0.25, and e1 = 0.125. Thus we have ψ1 (ξ, η) = 0.25(−ξ − η + ξη) + 0.125(ξ 2 + η2 ) Similarly, the other functions can be determined. Problem 9.3: Calculate the interpolation functions ψi (x, y) for the quadratic triangular element shown in Fig. P9.3. Hint: Use Eq. (9.2.16), where Li are given by Eq. (8.2.25). PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

297

y (10,10) 3 6 1

5

x

4 2

(15,−3)

Figure P9.3 Solution: Using the procedure described in Example 9.2.1, we obtain ψ1 = L1 (2L1 − 1), ψ2 = L2 (2L2 − 1), ψ3 = L3 (2L3 − 1) ψ4 = 4L1 L2 , ψ5 = 4L2 L3 , ψ6 = 4L1 L3 where Li (i = 1, 2, 3) are the linear interpolation functions ψi of Eq. (8.2.25). The coefficients αi , βi and γi for the element shown are α1 = 150 − (−30) = 180, α2 = 0, α3 = 0, β1 = −13, β2 = 10 β3 = 3, γ1 = −5, γ2 = −10, γ3 = 15 The interpolation functions become (2A = α1 + α2 + α3 ) L1 =

1 1 1 (180 − 13x − 5y) , L2 = (10x − 10y) , L3 = (3x + 15y) 180 180 180

Hence, the quadratic function ψ1 for node 1 of the given element is ψ1 (x, y) = L1 (2L1 − 1) =

1 (180 − 13x − 5y) (90 − 13x − 5y) 180 × 90

Similarly, we obtain 1 (x − y) (−9 + x − y) 162 1 (x + 5y) (−30 + x + 5y) ψ3 (x, y) = L3 (2L3 − 1) = 1800 1 (180 − 13x − 5y) (x − y) ψ4 (x, y) = 4L1 L2 = 810 1 ψ5 (x, y) = 4L2 L3 = (x − y) (x + 5y) 1080 1 (180 − 13x − 5y) (x + 5y) ψ6 (x, y) = 4L3 L1 = 10800 ψ2 (x, y) = L2 (2L2 − 1) =

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

298

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 9.4: Determine the interpolation function ψ14 in terms of the area coordinates, Li for the quartic triangular element shown in Fig. P9.4. Solution: Using Eq. (9.2.14), we obtain the 4th degree polynomial (k = 5 and n = 15). First, note that ψ14 must vanish along lines L1 = 0, L2 = 0 and L3 = 0. It must also vanish on line L2 = 1/4. Thus ψ14 =

L1 − 0 L2 − 0 L3 − 0 L2 − 14 1 2 1 2 1 = 32L1 L2 L3 (4L2 − 1) 4 −0 4 −0 4 −0 4 − 4 s(1) = 0 9

10

3

11

8 15

12 13

1

1

s( 2 ) =

s( 2 ) = 0

7

14

2

6 2

3

1 4

4

s(3 ) = 0

5

Figure P9.4 Problem 9.5: Derive the interpolation function of a corner node in a cubic serendipity element. η 10

2

9

8

7

11

6

12

5

1

2

3

ξ

4

2

Figure P9.5 Solution: First we note that the polynomials used for rectangular serendipity elements should not contain terms under the cone of Figure 9.2.5. For the element under consideration, the polynomial form is given in Eq. (9.2.32). Now consider node 1 of Figure 9.2.8. The function ψ1 must vanish on lines ξ = 1 and η = 1. In addition, it should vanish at nodes 2, 3, 5 and 7. For any corner node, the interpolation function is of the form ψi (ξ, η) = (1 + ξi ξ)(1 + ηi η)(ai + bi ξ 2 + ci η2 ), PROPRIETARY MATERIAL.

i = 1, 2, 9 or 12

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

299

where (ξi , ηi ) denote the local coordinates of the corner nodes. For node 1, we have ξ1 = −1 and η1 = −1, and ψ1 has the form ψ1 (ξ, η) = (1 − ξ)(1 − η)(a1 + b1 ξ 2 + c1 η 2 ) We must determine the constants a1 , b1 , and c1 using the conditions, 1 1 ψ1 (−1, −1) = 1, ψ1 (− , −1) = 0, ψ1 (−1, − ) = 0 3 3 These conditions give the relations 1 b1 c1 a1 + b1 + c1 = , a1 + + c1 = 0, a1 + b1 + =0 4 9 9 whose solution is: a1 = −10/32, b1 = c1 = 9/32, and the interpolation function ψ1 becomes 1 ψ1 (ξ, η) = (1 − ξ)(1 − η)[−10 + 9(ξ 2 + η 2 )] 32 For a node intermediate to the corner nodes, the interpolation functions take a different form. For nodes 2 and 3, for example, ψ must vanish at ξ = −1, ξ = 1 and η = 1: ψi (ξ, η) = (1 − ξ 2 )(1 − η)(ai + bi ξ), i = 2 or 3 and for nodes 5 and 7, ψ must vanish at ξ = 1, η = −1 and η = 1. ψi (ξ, η) = (1 − ξ)(1 − η 2 )(ai + bi η),

i = 5 or 7

The constants ai and bi are to be determined using the interpolation property. As an example, consider node 2. We have ψ2 (ξ, η) = (1 − ξ 2 )(1 − η)(a2 + b2 ξ) The a2 and b2 are to be determined from the conditions, 1 1 ψ2 (− , −1) = 1, ψ2 ( , −1) = 0 3 3 which give a2 = −b2 /3 = 9/32. Hence, ψ2 (ξ, η) =

9 (1 − ξ 2 )(1 − η)(1 − 3ξ) 32

Problem 9.6: Consider the five-node element shown in Fig. P9.6. Using the basic linear and quadratic interpolations along the coordinate directions ξ and η, derive PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

300

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

the interpolation functions for the element. Note that the element can be used as a transition element connecting four-node elements to eight- or nine-node elements. η 4

5

3

ξ

2 2

1

2

Figure P9.6 Solution: First, we construct the interpolation function associated with node 5. It should vanish at ξ = 1, ξ = −1, and η = −1. Hence, it should be of the form ψ5 (ξ, η) = c5 (1 − ξ)(1 + ξ)(1 + η) The constant c5 is determined from the condition ψ5 (0, 1) = 1. We have c5 = 1/2. 1 ψ5 (ξ, η) = (1 − ξ 2 )(1 + η) 2 For any corner node of the bilinear element, the interpolation function is of the form ψˆi (ξ, η) = (1 + ξi ξ)(1 + ηi η) where (ξi , ηi ) denote the local coordinates of the corner nodes: (ξ1 , η1 ) = (−1, −1), (ξ2 , η2 ) = (1, −1), (ξ3 , η3 ) = (1, 1), (ξ4 , η4 ) = (−1, 1) These should be corrected to vanish at node 5: (ξ5 , η5 ) = (0, 1). The bilinear functions ψˆ1 and ψˆ2 already satisfy this property [i.e., vanish at point (0,1)]. Thus, ψ1 = ψˆ1 , ψ2 = ψˆ2 , and we need to correct only ψˆ3 and ψˆ4 so that they vanish at the point (0,1). These functions take a value of 0.5 at node 5, while ψ5 takes a value of unity. Therefore, 0.5×ψ5 should be subtracted from ψˆ3 and ψˆ4 to obtain the required functions. The final result is 1 1 ψ1 = (1 − η)(1 − ξ), ψ2 = (1 + ξ)(1 − η) 4 4 1 1 1 ψ3 = (1 + ξ)(1 + η)ξ, ψ4 = − (1 − ξ)(1 + η)ξ, ψ5 = (1 − ξ 2 )(1 + η) 4 4 2 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

301

Problem 9.7: (Nodeless variables) Consider the four-node rectangular element with interpolation of the form u

4 X

ui ψi +

i−1

4 X

ci φi

i=1

where ui are the nodal values and ci are arbitrary constants. Determine the form of ψi and φi for the element. Solution: Since ui is the value of u at the i−th node of the element, the second part should be identically zero at the nodes. This implies, for non—zero values of the parameters (c1 , c2 , c3 , c4 , that (φ1 , φ2 , φ3 , φ4 ) should take the value of zero at the i−th node, and be linearly independent. Thus, ψi , (i = 1, 2, 3, 4) are the linear interpolation functions of the four—node rectangular element, and φi are the lowest order polynomials that satisfy the requirement, φi (ξj , ηj ) = 0 for any i and j. The following functions satisfy the requirement φ1 = (1 − ξ 2 ), φ2 = (1 − η2 ), φ3 = (1 − ξ 2 )η, φ4 = ξ(1 − η 2 ) Problems 9.8—9.10: Determine the Jacobian matrix and the transformation equations for the elements given in Fig. P9.8—P9.10.

y 10 in.

4

10 3

3

60o

10 in.

1

x

2

Figure P9.8 Solution to Problem 9.8: The transformation equations are x=

4 X

xi ψi = 13.66 + 5ξ + 8.66η,

y=

i=1

4 X

yi ψi = 5(1 + η)

i=1

The Jacobian matrix can be computed using the definition or using Eq. (9.3.11b):

[J] =

"

∂x ∂ξ ∂x ∂η

∂y ∂ξ ∂y ∂η

#

⎡

=⎣

∂ ψˆ1 ∂ξ ∂ ψˆ1 ∂η

PROPRIETARY MATERIAL.

∂ ψˆ2 ∂ξ ∂ ψˆ2 ∂η

∂ ψˆ3 ∂ξ ∂ ψˆ3 ∂η

∂ ψˆ4 ∂ξ ∂ ψˆ4 ∂η

⎤

⎡

x1 ⎢ x2 ⎦⎢ ⎣ x3 x4

⎤

y1 y2 ⎥ ⎥ y3 ⎦ y4

c The McGraw-Hill Companies, Inc. °

All rights reserved.

302

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

⎡

⎤

0.0 0.0 1 −(1 − η) 10.0 0.0 ⎥ (1 − η) (1 + η) −(1 + η) ⎢ ⎢ ⎥ = ⎣ 27.32 10.0 ⎦ (1 − ξ) 4 −(1 − ξ) −(1 + ξ) (1 + ξ) 17.32 10.0 ∙ ¸ 5.0 0.0 = 8.66 5.0 ∙

¸

Thus, the Jacobian is a positive number, J = 25.

y

3

(6.5,7)

4

5 cm 1

2

x

5 cm

Figure P9.9

Solution to Problem 9.9: The coordinates of the element nodes are: ⎡

0.0 ⎢ 5.0 ⎢ ⎣ 6.5 0.0

⎤

0.0 0.0 ⎥ ⎥ 7.0 ⎦ 5.0

The transformation equations are 4 X

4 X 1 1 xi ψi = (1 + ξ)(11.5 + 1.5η), y = yi ψi = (1 + η)(12 + 2ξ) x= 4 4 i=1 i=1

The Jacobian matrix is given by [J] = The Jacobian is

" ∂x

∂ξ ∂x ∂η

∂y ∂ξ ∂y ∂η

#

∙

2.875 + 0.375η = 0.375 + 0.375ξ

0.5 + 0.5η 3.0 + 0.5ξ

¸

1 J = (67.5 + 7.5η + 10ξ) 8

which is positive for any (ξ, η) such that −1 ≤ ξ ≤ 1 and −1 ≤ η ≤ 1.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

y

5 cm

η

5 cm

6

3 cm

•6 7• •4 1 2 • •

8

7

4 5

3 cm 2

1

3 cm

3

3 cm

1.5 cm x 0.5 cm

• 5 • 3 •

303

ψ1 = − 14 (1 − ξ )(1 − η )(1 + ξ + η ) ψ 2 = 12 (1 − ξ 2 )(1 − η )

8

ξ

ψ 3 = − 14 (1 + ξ )(1 − η )(1 − ξ + η ) ψ 4 = 12 (1 − ξ )(1 − η 2 ), ψ 5 = 12 (1 + ξ )(1 − η 2 ) ψ 6 = − 14 (1 − ξ )(1 + η )(1 + ξ − η ) ψ 7 = 12 (1 − ξ 2 )(1 + η ) ψ 8 = − 14 (1 + ξ )(1 + η )(1 − ξ − η )

Figure P9.10 Solution to Problem 9.10: Note that the node numbering used in Figure P9.10 is the same as that used for the (master) element in Figure 9.2.8. The matrix of nodal coordinates is given by ⎡ ⎤ 0.0 0.0 ⎢ 3.0 0.0 ⎥ ⎢ ⎥ ⎢ 6.0 0.0 ⎥ ⎢ ⎥ ⎢ ⎥ ⎢ 0.0 3.0 ⎥ ⎢ ⎥ ⎢ 6.5 1.5 ⎥ ⎢ ⎥ ⎢ 0.0 6.0 ⎥ ⎢ ⎥ ⎣ 5.0 6.0 ⎦ 10.0 6.0 The transformation equations are x=

8 X

xi ψˆi (ξ, η) = 3.25 + 3.25ξ + η + ξη + 0.75η2 + 0.75ξη 2

i=1

y=

8 X i=1

yi ψˆi (ξ, η) = 2.25 − 0.75ξ + 3η + 0.75η 2 + 0.75ξη2

The Jacobian matrix becomes [J] =

" ∂x

∂ξ ∂x ∂η

∂y ∂ξ ∂y ∂η

#

=

∙

3.25 + η + 0.75η 2 (1 + 1.5η)(1 + ξ)

−0.75 + 0.75η 2 3.0 + 1.5η(1 + ξ)

¸

The Jacobian is J = 10.5 + 0.75ξ + 9η + 6ξη + 3η 2 + 0.75ξη 2 A plot of the Jacobian shows that J = 0 at ξ = 1 and η = −1 and J > 0 everywhere else. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

304

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 9.11: Using the Gauss quadrature, determine the contribution of a constant distributed source to nodal points of the four-node finite element in Fig. P9.9. Solution: The integral to be evaluated is fie =

Z

Ωe

f0 ψie (x, y) dxdy =

Z 1 Z 1

−1 −1

f0 ψ e (ξ, η)J dξdη

Note that the integrand is quadratic in ξ and η. Hence, a 2 × 2 Gauss rule would evaluate the integrand exactly. For example, we have (see Problem 9.9 for the Jacobian) f1e = =

= = = =

Z 1 Z 1

1 1 f0 (1 − ξ)(1 − η) (67.5 + 7.5η + 10ξ) dξdη 4 8 −1 −1 ∙ Z f0 1 1 10 (1 − η) (1 − √ )(67.5 + 7.5η + √ ) 32 −1 3 3 ¸ 1 10 + (1 + √ )(67.5 + 7.5η − √ ) dη 3 3 Z 1 f0 10 (1 − η)(67.5 + 7.5η − ) dη 16 −1 3 ∙ ¸ 7.5 10 7.5 10 1 1 f0 √ √ √ √ )(67.5 + − ) + (1 + )(67.5 − − ) (1 − 16 3 3 3 3 3 3 7.5 10 f0 (67.5 − − ) 8 3 3 185 f0 = 7.70833f0 24

Similarly, the remaining three components can be computed: f1e = 7.7083f0 , f2e = 8.5417f0 , f3e = 9.1667f0 , f4e = 8.3333f0 Problem 9.12: For a 12-node serendipity (cubic) element, as illustrated in Fig. P9.12, show that the Jacobian J = J11 is J = 0.4375 + 0.84375(b − a) + 0.5625η − 0.84375(b − a)η + 1.125ξ − 0.5625(a + b)ξ − 1.125ηξ + 0.5625(a + b)ηξ + 1.6875ξ 2 − 2.53125(b − a)ξ 2 − 1.6875ηξ 2 + 2.53125(b − a)ηξ 2 What can you conclude from the requirement J > 0?

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

y

305

Square element

Equally spaced Nodes, except for these nodes

2

(a,0) (b,0)

x

Figure P9.12 Solution: We have (after a lengthy algebra using Maple) x = 0.4375 + 0.28125(a + b) + 0.4375ξ + 0.5625η + 0.84375(b − a)ξ − 0.28125(a + b)η + 0.5625ξη + 0.84375(a − b)ξη

+ 0.5625ξ 2 − 0.28125(a + b)ξ 2 − 0.5625ηξ 2 + 0.28125(a + b)ηξ 2

+ 0.5625ξ 3 + 0.84375(a − b)ξ 3 − 0.5625ηξ 3 + 0.84375(b − a)ηξ 3 y =1+η Hence, the Jacobian is J = J11 because J12 = 0 and J22 = 1 J = J11 = 0.4375 + 0.84375(b − a) + 0.5625η − 0.84375(b − a)η + 1.125ξ − 0.5625(a + b)ξ − 1.125ηξ + 0.5625(a + b)ηξ + 1.6875ξ 2 − 2.53125(b − a)ξ 2 − 1.6875ηξ 2 + 2.53125(b − a)ηξ 2 Note that J(ξ, η = −1) = −0.125 + 1.6875(b − a) + 2.25ξ − 1.125(a + b)ξ

+ 3.375ξ 2 − 5.0625(b − a)ξ 2 J(ξ, η = +1) = 1.0

Thus J = J11 > 0 ensures a unique transformation and preservation of the sense of the coordinate system in the master rectangular element, provided a and b are such that 5.5 − 1.125(a + b) − 3.375(b − a) > 0 and 1.0 + 1.125(a + b) − 3.375(b − a) > 0 The above inequalities place a restriction on the values of a and b. Clearly, for a > 0.666667 and b = 1.333333 (the usual location of the midside nodes), the inequalities are met (i.e., J = 1 > 0). A plot of the Jacobian shows, for example, that J = 0 when (i) a = 0.27777 = 5/18 and (ii) b = 1 and J < 0 for a = 0.27777 and any b < 0.4745. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

306

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 9.13: Determine Jacobian of the eight-node rectangular element of Fig. P9.13 in terms of the parameter a. y, η

•6 7• •4 1 2 •• a

ψ1 = − 14 (1 − ξ )(1 − η )(1 + ξ + η )

• 5 • 3 •

ψ 2 = 12 (1 − ξ 2 )(1 − η )

8

ψ 3 = − 14 (1 + ξ )(1 − η )(1 − ξ + η )

x, ξ

ψ 4 = 12 (1 − ξ )(1 − η 2 ), ψ 5 = 12 (1 + ξ )(1 − η 2 ) ψ 6 = − 14 (1 − ξ )(1 + η )(1 + ξ − η ) ψ 7 = 12 (1 − ξ 2 )(1 + η ) ψ 8 = − 14 (1 + ξ )(1 + η )(1 − ξ − η )

Figure P9.13 Solution: Using the coordinate system (x, y), which coincides with the natural coordinate system (ξ, η), we obtain a x = ξ − (1 − ξ 2 )(1 − η), y = η 2 The Jacobian is given by J = J11 (J12 = 0 and J22 = 1) J = 1.0 + a(1 − η)ξ

which is zero at (i) (ξ, η) = (−1, −1) when a = 0.5 (left quarter point) and (ii) (ξ, η) = (1, −1) when a = −0.5 (right quarter point). The Jacobian is negative when the node is placed inside a quarter point and the nearest corner node. Problem 9.14: Determine the conditions on the location of node 3 of the quadrilateral element shown in Fig. P9.14. Show that the transformation equations are given by 1 x = (1 + ξ) [2(1 − η) + a(1 + η)] 4 1 y = (1 + η) [2(1 − ξ) + b(1 + ξ)] 4

y

3

(a, b)

4

2" 1

2

2"

x

Figure P9.14 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

307

Solution: The transformation equations are x= y=

4 X

1 xi ψi = (1 + ξ) [2(1 − η) + a(1 + η)] 4 i=1

4 X

1 yi ψi = (1 + η) [2(1 − ξ) + b(1 + ξ)] 4 i=1

The Jacobian matrix is ⎡

⎤

0 0 ⎥ 1 −(1 − η) (1 − η) (1 + η) −(1 + η) ⎢ ⎢2 0⎥ [J] = 4 −(1 − ξ) −(1 + ξ) (1 + ξ) (1 − ξ) ⎣ a b ⎦ 0 2 ∙ ¸ 1 2(1 − η) + a(1 + η) (b − 2)(1 + η) = (a − 2)(1 + ξ) 2(1 − ξ) + b(1 + ξ) 4 ∙

¸

The Jacobian is given by J=

1 [a(1 + η) + b(1 + ξ) − 2(ξ + η)] 4

For positive Jacobian at the point (ξ, η)=(1,1), it follows that a+b > 2. In particular, J = 0 when a = 0.5, b = 1.5 and ξ = η = 1.0. Problem 9.15: Determine the global derivatives of the interpolation functions for node 3 of the element shown in Fig. P9.9. Solution: The inverse of the Jacobian matrix is given by J −1 =

∙

1 3 + 0.5ξ −0.5(1 + η) J −0.375(1 + ξ) 2.875 + 0.375η

¸

Hence, the global derivatives of the interpolation functions for node 3 of the element in Figure P9.9 are ∂ ψˆ3 5(1 + η) ∂ ψˆ3 5(1 + ξ) = , = ∂x 8J ∂y 8J where J = (135 + 15η + 20ξ)/16. Problem 9.16: Let the transformation between the global coordinates (x, y) and local normalized coordinates (ξ, η) in a Lagrange element Ωe be x=

m X

xi ψˆi (ξ, η),

i=1

PROPRIETARY MATERIAL.

y=

m X

yi ψˆi (ξ, η)

i=1

c The McGraw-Hill Companies, Inc. °

All rights reserved.

308

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

where (xei , yie ) denote the global coordinates of the element nodes. The differential lengths in the two coordinates are related by dxe = or

½

∂xe ∂xe dξ + ∂η, ∂ξ ∂η

dxe dye

¾

=

" ∂xe ∂ξ ∂ye ∂ξ

∂ye ∂ye ξ+ dη ∂ξ ∂η

dye =

∂xe ∂η ∂ye ∂η

#½

dξ dη

¾

= [J]

½

dξ dη

¾

In the finite element literature the transpose of [T ] is called the Jacobian matrix, [J]. Show that the derivatives of the interpolation function ψie (ξ, η) with respect to the global coordinates (x, y) are related to their derivatives with respect to the local coordinates (ξ, η) by e ( ∂ψe )

⎧ 2 e ∂ ψi ⎪ ⎪ ⎪ ⎨ ∂x2 ⎪ ⎪ ⎪ ⎩

∂ 2 ψie ∂y2 ∂ 2 ψie ∂x∂y

⎫ ⎪ ⎪ ⎪ ⎬ ⎪ ⎪ ⎪ ⎭

⎡³

∂xe ∂ξ

´2

⎢³ ⎢ ∂x ´2 e ⎣ ∂η

( ∂ψ ) i

i

∂x ∂ψie ∂y

= [J]

³

−1

∂ξ ∂ψie ∂η

´ ∂ye 2 ∂ξ ³ ´ ∂y 2

⎤−1

e ∂ye 2 ∂x ∂ξ ∂ξ

⎥

⎥ ∂xe ∂ye ⎥ 2 ⎦ ∂η ∂η ∂η ∂ye ∂ye ∂xe ∂ye ∂xe ∂ye ∂xe ∂xe + ∂ξ ∂η ∂ξ ∂η ∂η ∂ξ ∂ξ ∂η ⎛⎧ ∂ 2 ψe ⎫ ⎡ 2 ⎞ ∂ 2 ye ⎤ ∂ xe i ⎪ ⎪ ⎪ ⎪ ( ) e 2 2 ∂ψi ∂ξ 2 ⎨ ∂ξ ⎪ ⎬ ⎢ ∂ξ ⎜⎪ ⎟ ⎥ 2x ⎜ ∂ 2 ψie ∂ 2 ye ⎥ ∂xe ⎟ ∂ e ⎢ × ⎜ ∂η2 − ⎣ ∂η2 ⎟ 2 ∂ψ ∂η ⎦ i ⎪ ⎝⎪ ⎠ ⎪ ⎪ ⎪ ∂y ∂ 2 ye ∂ 2 xe ⎩ ∂ 2 ψie ⎪ ⎭ ∂ξ ∂η ∂ξ∂η ∂ξ∂η

=⎢

e

Problem 9.17: (Continuation of Problem 9.16) Show that the Jacobian can be computed from the equation

[J] =

( ∂ψe 1

∂ψ2e

∂ξ ∂ψ1e ∂η

∂ξ ∂ψ2e ∂η

··· ···

e ∂ψn

∂ξ e ∂ψn ∂η

)

⎡ e x1 ⎢ xe ⎢ 2 ⎢ . ⎣ ..

xen

⎤

y1e y2e ⎥ ⎥ .. ⎥ . ⎦

yne

Solution of Problems 16 and 17: Part of the Problem 9.16 and all of Problem 9.17 is already discussed in the problem statement. The same procedure as that used for the first derivatives can be used (i.e. chain rule of differentiation) for the second derivatives and arrive at the required result. For example, we have ∂ψi ∂ψi ∂x ∂ψi ∂y ∂ψi ∂ψi ∂x ∂ψi ∂y = + , = + ∂ξ ∂x ∂ξ ∂y ∂ξ ∂η ∂x ∂η ∂y ∂η PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

309

and µ

¶

∂ 2 ψi ∂ ∂ψi ∂x ∂ψi ∂y + = 2 ∂ξ ∂ξ ∂x ∂ξ ∂y ∂ξ µ ¶ µ ¶ ∂ ∂ψi ∂x ∂ψi ∂ 2 x ∂ ∂ψi ∂y ∂ψi ∂ 2 y = + + + ∂ξ ∂x ∂ξ ∂x ∂ξ 2 ∂ξ ∂y ∂ξ ∂y ∂ξ 2 µ ¶ 2 ∂ 2 ψi ∂x ∂ 2 ψi ∂x ∂y ∂ψi ∂ 2 x + = + 2 ∂x ∂ξ ∂x∂y ∂ξ ∂ξ ∂x ∂ξ 2 µ ¶ ∂ 2 ψi ∂y 2 ∂ 2 ψi ∂x ∂y ∂ψi ∂ 2 y + + + ∂y 2 ∂ξ ∂x∂y ∂ξ ∂ξ ∂y ∂ξ 2 Similarly, the second derivative with respect to η and the mixed derivative can be evaluated: µ

¶

∂ 2 ψi ∂x 2 ∂ 2 ψi ∂x ∂y ∂ψi ∂ 2 x ∂ψi ∂ 2 y ∂ 2 ψi ∂ 2 ψi + = + 2 + + ∂η2 ∂x2 ∂η ∂x∂y ∂η ∂η ∂x ∂η 2 ∂y ∂η 2 ∂y 2 µ ¶ ∂ 2 ψi ∂ 2 ψi ∂y ∂y ∂ 2 ψi ∂x ∂x ∂ 2 ψi ∂x ∂y ∂x ∂y + = + + ∂η∂ξ ∂x2 ∂ξ ∂η ∂x∂y ∂η ∂ξ ∂ξ ∂η ∂y 2 ∂ξ ∂η 2 2 ∂ψi ∂ x ∂ψi ∂ y + + ∂x ∂η∂ξ ∂y ∂η∂ξ

µ

∂y ∂η

¶2

Since we need to write the global derivatives in terms of the local derivatives, set up the equations for the global derivatives from the above three equations. This will yield the required equations. Problem 9.18: Find the Jacobian matrix for the nine-node quadrilateral element shown in Fig. P9.18. What is the determinant of the Jacobian matrix? y

3"

3" 4

3

7

2"

8

9

1

5

6

2" 2"

2 2"

1"

x

0.5"

Figure P9.18 Solution: This problem is similar to one in Problem 9.10 (see Figure P9.10), except that it is a nine-node element used here. Once again we note that the node numbering used in Figure P9.14 is different from that used for the master element in Figure 9.6. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

310

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

The matrix of nodal coordinates is ⎡

0.0 ⎢ 2.0 ⎢ ⎢ 4.0 ⎢ ⎢ 0.0 ⎢ ⎢ ⎢ 2.5 ⎢ ⎢ 4.5 ⎢ ⎢ 0.0 ⎢ ⎣ 3.0 6.0

⎤

0.0 0.0 ⎥ ⎥ 0.0 ⎥ ⎥ 2.0 ⎥ ⎥ ⎥ 2.0 ⎥ ⎥ 1.0 ⎥ ⎥ 4.0 ⎥ ⎥ 4.0 ⎦ 4.0

The transformation equations are x= y=

i 1h xi ψˆi (ξ, η) = 10 + ξ(9 − ξ − 6ξη) + 2η(1 − 2ξ) − 5ξη 2 (1 + ξ) 4 i=1

9 X 9 X

1 yi ψˆi (ξ, η) = (1 + η) [4 − ξ(1 + ξ)(1 + η)] 2 i=1

The Jacobian matrix becomes [J] = =

" ∂x ∂ξ ∂x ∂η

∙

∂y ∂ξ ∂y ∂η

#

1 9 − 4η − 2ξ(1 + 6η) − 5η 2 (1 + 2ξ) −2(1 + 2ξ)(1 + η)2 2(1 + ξ)(1 − 3ξ − 5ξη) 8 − 4ξ(1 + ξ)(1 + η) 4

¸

The Jacobian is J = 4.75 − 3.25ξ − 1.5η − 8.5ξη − 3.5ξ 2 − 2.25η 2 − 5.25ξη 2 − 5ηξ 2 − ξ 3 − 2ξ 3 η − 1.5ξ 2 η 2 − ξ 3 η 2

Problem 9.19: For the eight-node element shown in Fig. P9.19, show that the x-coordinate along the side 1—2 is related to the ξ-coordinate by the relation x = − 12 ξ(1 − ξ)xe1 + 12 ξ(1 + ξ)xe2 + (1 − ξ 2 )xe5 and that the relations ξ=2

µ ¶1/2

PROPRIETARY MATERIAL.

x a

− 1,

∂x = (xa)1/2 ∂ξ

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

311

hold. Also, show that " µ ¶ 1/2

x uh (x, 0) = − 2 a

¯

"

#"

−1

1−

µ ¶1/2 # µ ¶1/2

x + −1 + 2 a

∂uh ¯¯ 1 =− ¯ ∂x ¯(x,0) (xa)1/2 "

µ ¶1/2 #

x a

( "

x a

ue2 + 4

µ ¶1/2 #

1 x 3−4 2 a

µ ¶1/2 #

x +2 1 − 2 a

ue5

ue1

ue1

"µ ¶ 1/2

x a

"

#

x e − u a 5

µ ¶1/2 #

x 1 + −1 + 4 2 a

)

ue2

Thus, ∂uh /∂x grows at a rate of (xa)−1/2 as x approaches zero along the side 1—2. In other words, we have a x−1/2 singularity at node 1. Such elements are used to fracture mechanics problems. y 4

3

7

0.75 a 6 8 0.25 a 1 5

2

x

0.25a 0.75a

Figure P9.19 Solution: The transformation equation for x is given by 1 1 x = x1 · (1 − ξ)(1 − η)(−1 − ξ − η) + x5 · (1 − ξ 2 )(1 − η) 4 2 1 + x2 · (1 + ξ)(1 − η)(−1 + ξ − η)|η = −1 4 Substituting x1 = 0, x2 = a, x5 = a/4, we obtain x=

a a (1 − ξ 2 ) + ξ(1 + ξ) 4 2

The roots of the above equation are (ξ)1 = 2

r

r

x − 1, (ξ)2 = −2 a

x −1 a

The second √ root is not admissible here. Differentiating ξ with respect to x, we obtain ∂ξ/∂x = 1/ ax. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

313

SOLUTIONS MANUAL

New Problem 9.1: Determine the interpolation functions for the rectangular element shown in Fig. NP9.1. Hint: Make use of the one-dimensional interpolation functions and the interpolation properties. p5 (ξ )

7

4

η

6

4

3

η

1

5

ξ

p6 (ξ )

1

7

ξ

4

3

6

p7 (ξ )

1

7

η

ξ

5

3

6 5

η 1 4

7

2

ξ

5

2 3

1 3

4

2

1

1

2

1

2

2

3

6

7

η

2

ξ

1

2 3

1

4

3

6

1 3

1 1 2

7

η ξ

5

1

2

3

6 5

2

Figure NP.1 Solution: First, note the following interpolation functions associated with nodes 5, 6, and 7: 2

p5 (η) = (1 − η ),

µ

¶

1 27 p6 (ξ) = (1 − ξ 2 ) +ξ , 16 3

µ

1 27 p7 (ξ) = (1 − ξ 2 ) −ξ 16 3

¶

Then the interpolation functions associated with nodes 5, 6, and 7 can be written as ψ5 (ξ, η) = p5

∙

¸

1 (1 + ξ) , 2

ψ6 (ξ, η) = p6 (ξ)

∙

¸

1 (1 + η) , 2

ψ7 (ξ, η) = p7 (ξ)

∙

¸

1 (1 + η) 2

The interpolation functions associated with the corner nodes can be constructed as follows: 1 ψ1 (ξ, η) = (1 + ξ)(1 + η), 4 1 ψ3 (ξ, η) = (1 − ξ)(1 − η) − 4 1 ψ4 (ξ, η) = (1 − ξ)(1 + η) − 4

PROPRIETARY MATERIAL.

1 1 ψ2 (ξ, η) = (1 + ξ)(1 − η) − ψ5 (ξ, η) 4 2 1 2 1 ψ5 (ξ, η) − ψ6 (ξ, η) − ψ7 (ξ, η) 2 3 3 1 2 ψ6 (ξ, η) − ψ7 (ξ, η) 3 3

c The McGraw-Hill Companies, Inc. °

All rights reserved.

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGrawHill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

SOLUTIONS MANUAL

315

Chapter 10 FLOWS OF VISCOUS INCOMPRESSIBLE FLUIDS

Problem 10.1: Consider Eqs. (10.1) and (10.2) in cylindrical coordinates (r, θ, z). For axisymmetric flows of viscous incompressible fluids (i.e., flow field is independent of θ coordinate), we have ρ

∂u 1 ∂ σθθ ∂σrz = (rσrr ) − + + fr ∂t r ∂r r ∂z ρ

where

(i)

1 ∂ ∂σzz ∂w = (rσrz ) + + fz ∂t r ∂r ∂z 1 ∂ ∂w (ru) + =0 r ∂r ∂z

(ii) (iii)

∂u u , σθθ = −P + 2µ ∂r r ¶ µ ∂u ∂w ∂w , σrz = µ + = −P + 2µ ∂z ∂z ∂r

σrr = −P + 2µ σzz

(iv)

Develop the semidiscrete finite element model of the equation by the pressure-velocity formulation. Solution: Weak Forms The weak forms of the three equations are ∙

Z

¸

∂u 1 ∂ σθθ ∂σrz − (rσrr ) + − − fr rdrdz 0 =2π w1 ρ ∂t r ∂r r ∂z Ωe ∙ ¸ Z ∂u ∂w1 σθ ∂w1 + σr + w1 + σrz − w1 fr rdrdz =2π ρw1 ∂t ∂r r ∂z Ωe − 2π Z

I

Γe

w1 tr r ds,

tr = σr nr + σrz nz

∙

(1b) ¸

∂w 1 ∂ ∂σzz − (rσrz ) − − fz rdrdz e ∂t r ∂r ∂z Ω ¸ Z ∙ ∂w ∂w2 ∂w2 + σrz + σz − w2 fz rdrdz =2π ρw2 ∂t ∂r ∂z Ωe

0 =2π

w2 ρ

− 2π

I

Γe

w2 tz r ds,

PROPRIETARY MATERIAL.

(1a)

tz = σrz nr + σzz nz

c The McGraw-Hill Companies, Inc. °

(2a)

(2b) All rights reserved.

316

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Z

∙

¸

∂w 1 ∂ (ru) − rdrdz e r ∂r ∂z Ω ¸ Z ∙ ∂ ∂w =2π −w3 (ru) − rw3 drdz ∂r ∂z Ωe

0 =2π

w3 −

(3a) (3b)

Semi-Discrete Finite Element Model For the interpolation of the form u(r, z) =

m X

uj ψj (r, z), w(r, z) =

j=1

m X

wj ψj (r, z), P (r, z) =

j=1

n X

Pj φj (r, z)

(4)

j=1

the finite element model is given by ⎫

⎤⎧

⎡

⎡

[M 11 ] [0] [0] u} ⎬ [K 11 ] ⎨ {¨ ⎣ [0] [0] ⎦ {¨ [M 22 ] v } + ⎣ [K 12 ]T ⎩ ¨ ⎭ 33 [0] [0] [M ] [K 13 ]T {P } =

Mij11 =Mij22 = 2π

13 Kij 22 Kij 23 Kij

Ωe

⎧ 1 ⎫ ⎨ {F } ⎬ ⎩

⎫

{F 2 } ⎭ {F 3 }

(5)

ρψi ψj rdrdz

∙ µ

Z

⎤⎧

[K 13 ] ⎨ {u} ⎬ [K 23 ] ⎦ {v} ⎭ ⎩ [K 33 ] {P }

¶

¸

ψi ψj ∂ψi ∂ψj ∂ψi ∂ψj + + rdrdz ∂r ∂r r r ∂z ∂z Ωe Z ∂ψi ∂ψj rdrdz =2π µ ∂z ∂r Ωe µ ¶ Z ∂ψi φj + ψi φj drdz = − 2π r ∂r Ωe µ ¶ Z ∂ψi ∂ψj ∂ψi ∂ψj +2 =2π µ rdrdz ∂r ∂r ∂z ∂z Ωe Z ∂ψi 33 φj rdrdz, Kij = − 2π = 0, Fi3 = 0 e ∂z Ω Z I

11 =2π Kij 12 Kij

Z

[K 12 ] [K 22 ] [K 23 ]T

Fi1 =2π Fi2 =2π

µ 2

e

ZΩ

Ωe

fr ψi rdrdz + 2π

fz ψi rdrdz + 2π

e

IΓ

Γe

ψi tr rds

ψi tz rds

(5)

Fully-Discretized Finite Element Model Equation (5) is of the general form ¨ + [K]{∆} = {F } [M ]{∆} PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

(7a) All rights reserved.

SOLUTIONS MANUAL

where {∆} =

⎧ ⎫ ⎨ {u} ⎬

{v} ⎭ {P }

⎩

317

(7b)

Then it follows that [see Eqs. (11.32)—(11.33b)]:

ˆ ˆ [K]{∆} s+1 = {F }s,s+1

(8)

ˆ = [M ] + a1 [K] [K] {Fˆ } = ([M ] − a2 [K]) {∆}s + a1 {F }s+1 + a2 {F }s

(9)

where

a1 = α∆t,

a2 = (1 − α)∆t

(10)

Problem 10.2: Develop the semidiscrete finite element model of the equations in Problem 10.1 using the penalty function formulation. Solution: For the finite element model, we begin with the weak forms of the first equation. Adding Eqs. (1b) and (2b) Z

∙

µ

¶

µ

¶

¸

∂u ∂w1 ∂u w1 u ∂w1 ∂u ∂w + 2µ + + +µ − w1 fr rdrdz ∂t ∂r ∂r r r ∂z ∂z ∂r Ωe µ ¶ ¸ Z ∙ ∂w ∂w ∂w2 ∂u ∂w2 ∂w +2π + +µ − w2 fz rdrdz ρw2 + 2µ ∂t ∂r ∂z ∂r ∂z ∂z Ωe ¶ I Z µ ∂w1 w1 ∂w2 −2π + + (w1 tr + w2 tz ) rds − P rdrdz (1) ∂r r ∂z Γe Ωe

0 =2π

ρw1

Since w1 and w2 satisfy the incompressibility constraint 1 ∂ ∂w2 (rw1 ) + =0 r ∂r ∂z

(2)

we can set Z

Ωe

µ

¶

∂w1 w1 ∂w2 + + P rdrdz = ∂r r ∂z

Z

Ωe

∙

¸

1 ∂ ∂w2 (rw1 ) + P rdrdz = 0 r ∂r ∂z

(3)

Next we add the following expression due to the constraint (2) to Eq. (1): γ

Z

Ωe

µ

∂w1 w1 ∂w2 + + ∂r r ∂z

¶µ

∂u u ∂w + + ∂r r ∂z

¶

rdrdz

(4)

This amounts to replacing P with P = −γ PROPRIETARY MATERIAL.

µ

∂u u ∂w + + ∂r r ∂z

¶

c The McGraw-Hill Companies, Inc. °

(5) All rights reserved.

318

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

The finite element model based on Eq. (1)+Eq. (4) is the same as that in Eq. (11.30) of the textbook with the coefficients

12 ¯ ij K 22 ¯ ij K

Z

µ

∂ψi + ∂r Ωe Z µ ∂ψi 12 + =Kij + 2πγ ∂r Ωe Z ∂φi ∂φj 22 =Kij + 2πγ Ωe ∂z ∂z

11 11 ¯ ij K =Kij + 2πγ

¶µ

¶

ψi ψj ∂ψj + r ∂r r ¶ ψi ∂φj rdrdz r ∂z

rdrdz

rdrdz

(6)

Problem 10.3: Write the fully discretized finite element equations of the finite element models in Problems 10.1 and 10.2. Use the α-family of approximation. Solution: The fully discretized models readily follow from Eqs. (10.5.30)—(10.5.32). Problem 10.4: The equations governing unsteady slow flow of viscous, incompressible fluids in the (x, y) plane can be expressed in terms of vorticity ζ and stream function ψ: ρ

∂ζ − µ∇2 ζ = 0, ∂t

−2ζ − ∇2 ψ = 0

Develop the semidiscrete finite element model of the equations. Discuss the meaning of the secondary variables. Use α-family of approximation to reduce the ordinary differential equations to algebraic equations. Solution: The weak forms of the equations are given by µ

Z

¶

∂ζ 0= − µ∇2 ζ dv w1 ρ e ∂t Ω ¶ Z µ I ∂ζ ∂ζ = + ∇w1 · ∇ζ dv − ρw1 w1 µ ds e e ∂t ∂n Ω Γ 0= =

Z Z

³

´

Ωe

w2 ζ − ∇2 ψ dv

Ωe

(w2 ζ + ∇w2 · ∇ψ) dv −

(1a) (1b) (2a)

I

Γe

∂ψ ds ∂n

(2b)

ψj (x)vj

(3)

w2

Suppose that w0s (x) and φs (x) are approximated as ζ(x) ≈

m X

j=1

ϕj (x)uj , ψ(x) ≈

n X

j=1

where uj are the nodal values of ζ and vj are nodal values of ψ. The finite element model is given by ∙

[M ] [0] [0] [0]

¸½

{u} ˙ {v} ˙

PROPRIETARY MATERIAL.

¾

+

∙

[A] [0] [B] [C]

¸½

{u} {v}

¾

=

½

c The McGraw-Hill Companies, Inc. °

{P } {Q}

¾

All rights reserved.

(4)

SOLUTIONS MANUAL

319

where Mij = Bij = Pi =

Z

e

ZΩ

e

IΩ

Γe

ρϕi ϕj dv , ψi ϕj dv ,

Aij = Cij =

qn1 ϕi ds ,

Qi =

qn1 = µ

∂ζ , ∂n

Z

Z

Ωe

Ωe

I

Γe

µ∇ϕi · ∇ϕj dv

∇ψi · ∇ψj dv

qn2 ψi ds

qn2 =

(5)

∂ψ ∂n

(6)

Problems 10.5—10.7 For the viscous flow problems given in Figs. P10.5—P10.7, give the specified primary and secondary degrees of freedom and their values. General comments The specified primary and secondary variables are clearly indicated in the figures, and therefore they are obvious. In general, both velocity components are zero on fixed walls, and shear stress is zero along the line of symmetry (see the discussion in the text). Nodes on the inlet have zero vertical velocities and specified horizontal velocities. Fixed wall 42

35 27

34 v y = 0

vx = 1

19

ty = 0

• •

11

• •

6 1

Figure P10.5

2

3

4

16

17

26 18

tx = 0

10 v = 0, v = 0 x y 5

v y = 0 , tx = 0

Solution of Problem 10.5: Horizontal velocity vx is known as unity at nodes 1, 6, 11, 19 and 27; vertical velocity vy is zero at nodes 1, 2, 3, 4, and 5, 10, 16, 17, 18 and 35 through 42; horizontal velocity is zero at nodes 5, 10, 16, 17, 18, 26, 34 and 42. The specified secondary variables are all zero: Fy = 0 at nodes 1, 6, 11, 19, 27; Fy = 0 at nodes 1, 2, 3, 4, 26 and 34. Solution of Problem 10.6: Horizontal velocity vx is known as zero at nodes 1—8, 15, 22, 29, 36, and 43—49; vertical velocity vy is zero at nodes 1—7 and it is vy = −1 at nodes 43 through 49; The specified secondary variables are all zero: Fy = 0 at nodes 1, 8, 15, 22, 29 and 36; Fx = Fy = 0 at nodes 7, 14, 21, 28, 35 and 42.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

320

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

v x = 0 , v y = −1

• •

vx = 0 ty = 0

8 1

2

3

• •

tx = 0 ty = 0

5

4

6

7

vx = 0 , v y = 0

Figure P10.6 Fixed wall Uniform flow

tx = t y = 0

y =1 L

Line of symmetry

x = 20 L

Figure P10.7 Solution of Problem 10.7: Vertical velocity component vy and horizontal stress tx must be zero along the horizontal line of symmetry. Rest of the boundary conditions are obvious. Problem 10.8: Consider the flow of a viscous incompressible fluid in a square cavity (Fig. P10.8). The flow is induced by the movement of the top wall (or lid) with a velocity vx = sin πx. For a 5 × 4 mesh of linear elements, give the primary and secondary degrees of freedom.

7

1 2

•

•

•

•

3

4

Fixed walls

vx = sin πx , v y = 0

5 6

Figure P10.8 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

321

Solution: All boundary conditions are on the primary variables. Except for the top, all velocity componenst aloing the fixed walls are zero; along the top wall, vy = 0 and vx (x) = sin πx. Problem 10.9: Consider the flow of a viscous incompressible fluid in a 90◦ plane tee. Using the symmetry and the mesh shown in Fig. P10.9. Write the specified primary and secondary variables for the computational domain. vx = 0 , t y = 0

Fixed walls

y

6 in.

10 in. Fixed wall

8 in.

vx = 1 vy = 0 Line of symmetry

x

8 in.

Figure P10.9 Solution: Vertical velocity component vy and horizontal stress tx must be zero along the horizontal line of symmetry. Rest of the boundary conditions are obvious from the figure (e.g., both velocity components are zero along the fixed wall). Problem 10.10: Repeat Problem 10.9 for the geometry shown in Fig. P10.10. Solution: Both velocity components are zero along the fixed wall; The velocities at the left boundary are specified to be vx = 1 and vy = 0 (fully-developed flow); The velocity vy = 0 at the right boundary. All specified secondary variables are zero (Fx = 0 at the right boundary).

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

322

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Fixed walls

vx = 1

vy = 0

vy = 0

tx = 0

Figure P10.10 New Problem 10.1: Consider the problem of (linear) bending of beams according to the Euler—Bernoulli beam theory. The principle of minimum total potential energy states that if the beam is in equilibrium then the total potential energy associated with the equilibrium configuration is the minimum; i.e., the equilibrium displacements are those which make the total potential energy a minimum. Thus, solving the equations governing the equilibrium of the Euler—Bernoulli beam is equivalent to minimizing the total potential energy Π(u0 , w0 ) = −

Z

xb ∙ EA

xa Z xb xa

2

µ

du0 dx

¶2

EI + 2

Ã

d2 w0 dx2

!2 ¸

dx

(fu0 + qw0 ) dx

(1)

where u0 and w0 are the axial and transverse displacements. The necessary condition for the minimum of a functional is that its first variation be zero: δΠ = 0, which yields the governing equations of equilibrium. As you know, the statement δΠ = 0 is the same as the weak forms of the governing equations of the Euler—Bernoulli beam theory. The weak form requires Hermite cubic interpolation of the transverse deflection w0 . Now suppose that we wish to relax the continuity required of the interpolation used for w0 (x) by introducing the relation dwo = ϕ(x) dx Then the total potential energy functional takes the form Π(u0 , w0 , ϕ) = − PROPRIETARY MATERIAL.

Z

xb ∙ EA

x Z xab xa

2

µ

du0 dx

¶2

+

EI 2

µ

(2)

dϕ dx

¶2 ¸

dx

(f u0 + qw0 ) dx

c The McGraw-Hill Companies, Inc. °

(3) All rights reserved.

SOLUTIONS MANUAL

323

Since the functional now contains only the first derivative of u0 and ϕ, Lagrange (minimum, linear) interpolation can be used. Thus the original problem is replaced with the following mathematical problem: ♣ Minimize Π(u0 , w0 , ϕ) in Eq. (3) subjected to the constraint dw0 − ϕ(x) = 0 (4) dx Develop the penalty function formulation of the constrained problem by deriving (a) the weak form and (b) the finite element model. Note: Much of the above discussion provides a background for the problem. The statements beginning with the symbol ♣ are all that you need to answer. Solution: The penalty functional is given by µ ¶ Z xb ∙ EA du0 2

µ

¶ ¸

EI dϕ 2 ΠP (u0 , w0 , ϕ) = + dx 2 dx 2 dx xa µ ¶2 Z xb Z γ xb dw0 − ϕ(x) (fu0 + qw0 ) dx + dx − 2 xa dx xa

(5)

The weak forms are given by setting δu I = 0, δw I = 0 and δφ I = 0: Z xb µ

¶

dδu0 du0 − f δu0 dx EA 0= dx dx xa ¶ ¸ Z xb ∙ µ dw0 dδw0 −ϕ − qδw0 dx γ 0= dx dx xa µ ¶ ¸ Z xb ∙ dw0 dϕ dδϕ 0= −γ − ϕ δϕ dx EI dx dx dx xa

(6a) (6b) (6c)

where (δu0 , δw0 , δϕ) can be viewed as the weight functins (w1 , w2 , w3 ). The finite element model is given by setting u0 (x) ≈ w0 (x) ≈ ϕ(x) ≈ We have

⎡

[K 11 ] ⎣ [K 12 ]T [K 13 ]T

m X

j=1 n X j=1 p X

uj ψj (x),

(1)

w1 ≡ δu0 = ψi

wj ψj (x),

(2)

w2 ≡ δw0 = ψi

(3)

w3 ≡ δϕ = ψi

Xj ψj (x),

j=1

[K 12 ] [K 22 ] [K 23 ]T

PROPRIETARY MATERIAL.

(1)

(2)

⎤⎧

(3)

⎫

⎧

(7) ⎫

[K 13 ] ⎨ {u} ⎬ ⎨ {F 1 } ⎬ [K 23 ] ⎦ {w} = {F 2 } ⎭ ⎩ ⎭ ⎩ {X} {F 3 } [K 33 ]

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(8)

324

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

where 11 Kij

=

Z

xa

22 Kij =γ 33 Kij =

Fi1 =

xb

Z

Z

xb

xa

xb

xa

Z

(1)

(1) dψi dψj EA dx, dx dx

xb

xa

⎛

12 = 0, Kij

(2)

(2) dψi dψj , dx dx

⎝EI

(3) (3) dψi dψj

(1)

f ψi

23 Kij = −γ

Z

xb

xa

⎞

13 Kij =0

(3) (3) + γψi ψj ⎠ dx

dx

dx

dx,

Fi2 =

Z

xb

xa

(2)

qψi

dx,

(2)

dψi (3) ψ dx dx j

Fi3 = 0

(9)

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

325

Chapter 11 PLANE ELASTICITY

Problems 11.1—11.3: Compute the contribution of the surface forces to the global force degrees of freedom in the plane elasticity problems given in Figs. P11.1—P11.3. Give nonzero forces for at least two global nodes. Problems 11.4—11.6: Give the connectivity matrices and the specified primary degrees of freedom for the plane elasticity problems given in Figs. P11.1—P11.3. Give only the first three rows of the connectivity matrix. General Note: A pin-type connection implies that both components ux and uy displacement are zero, whereas a roller support indicates the displacement un normal to the wall is zero. In the following problems Ui and Vi denote the horizontal and vertical displacements, respectively, at the global ith node of the mesh, and Fix and Fiy denotes the horizontal and vertical forces, respectively, at the global ith node of the mesh.

Plane stress ( h = 5 cm)

y

b = 3 cm

• •36 •29 •22 •15 •8 •1

E = 204 GPa , ν = 0.29, G = 79 GPa p0 43 49

• • 2

•

3

x

•

4

•

a = 6 cm

• • 5

•

• • • 28 • 21 • 14 • 7 • p 1

42 35

6

•

Figure P11.1 Solution to Problems 11.1 and 11.4: The specified primary degrees of freedom (i.e., displacements) are: U1 = V1 = 0, U43 = V43 = 0, U8 = 0, U15 = 0, U22 = 0, U29 = 0, U36 = 0

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

326

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

The specified secondary degrees of freedom (i.e., forces) with zero magnitudes are: F2x = F2y = 0, F3x = F3y = 0, F4x = F4y = 0, F5x = F5y = 0, F6x = F6y = 0 y y y x x x = F44 = 0, F45 = F45 = 0, F46 = F46 =0 F7y = 0, F44 y y y x x = F47 = 0, F48 = F48 = 0, F49 =0 F47

The nonzero (horizontal) forces at nodes 7, 14, 21, 28, 35, 42 and 49 can be computed as follows. The procedure to calculate the nodal forces is the same as that used for the calculation of nodal sources in Chapter 8 for single-variable problems, except that the nodal values must be decomposed into the x and y components. Since the distributed force is along the x coordinate, all nodal computed nodal forces are along the x coordinate. Assume that p0 and p1 have the units of N/m (if they are taken as N/m2 , the final nodal values should be multiplied with the factor h = 5 × 10−2 m). Note that a linearly varying force q of the type q(s) = q1e + (q2e − q1e )(

s ) Le

over an element ‘e’ of length Le , acting perpendicular to the length of the element, results in the nodal values of q e Le q e Le q1e Le (q2e − q1e )Le 1 + × = 1 + 2 2 2 3 3 6 q1e Le q2e Le q1e Le (q2e − q1e )Le 2 e + × = + F2 = 2 2 3 6 3

F1e =

q( s ) = q1e + (q2e − q1e )

s Le q2e

q1e

Le

1 3

q2e Le + 16 q2e Le

1 6

q2e Le + 13 q2e Le

Le

The above result can be used to find the nodal forces of the problem at hand. First note that the variation of q(s) is q(s) = p1 + (p0 − p1 )s/3, which can be used to determine q1e and q2e of each line element (Le = 0.5). For example, the element between (1) (1) global nodes 7 and 14 has the values: q1 = p1 and q2 = 5p1 /6+p0 /6. Similarly, the PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

(2)

(1)

(2)

327

(3)

next element has the values: q1 = q2 = 5p1 /6+p0 /6 and q2 = q1 = 2p1 /3+p0 /3. Hence, the horizontal forces at nodes 7 and 14, for example, are 17p1 + p0 p1 5p1 + p0 + = 6 72 72 µ ¶ µ ¶ 5p1 + p0 p1 5p1 + p0 2p1 + p0 5p1 + p0 + + = + = 12 36 36 36 12

F7x = x F14

Similarly, other values can be calculated Alternatively, the nonzero (horizontal) forces at nodes 7, 14, 21, etc. can be computed using the definition Qei

=

Z ya

tx (y)ψ1e (y) dy

yb

where Qei denotes the nodal force at node i of the element ‘e’, ψie denote the interpolation functions of the element, and y is the global coordinate (with origin at node 7). In the global coordinate system, with origin at node 7, the interpolation functions are given by ψ1e (y) =

yb − y , Le

ψ2e (y) =

y − ya Le

First, we note that the horizontal traction tx for the problem at hand is given by q(y) = p1 + (p0 − p1 )y/3. Then we have F7x

=

Qx7

=

Z 0.5

(1) q(y)ψ1 (y)

Z 0.5

(1) tx (y)ψ2 (y)

0

dy =

Z 0.5 ∙ 0

¸

p0 − p1 y (1 − 2y) dy p1 + 3

17p1 + p0 p1 p0 − p1 = = + 4 72 72 x F14

=

Qx14

=

0

dy +

Z 0.5 ∙

¸

Z 1

0.5

(2)

tx (y)ψ1 (y) dy Z

∙

¸

1 p0 − p1 p0 − p1 y (2y)dy + y 2(1 − y)dy p1 + p1 + = 3 3 0 0.5 ∙ µ ¶¸ p1 p0 − p1 5p1 + p0 p1 p0 − p1 + +2 = = + 4 36 4 18 12

etc. The connectivity matrix is given by (all that matters is the counterclockwise local node numbering; the elements are numbered as in FEM2D mesh generator) ⎡

⎤

1 2 9 8 ⎢ 2 3 10 9 ⎥ ⎢ ⎥ ⎢ 4 11 10 ⎥ [B] = ⎢ 3 ⎥ ⎣... ... ... ...⎦ 8 9 16 15 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

328

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Plane strain

10"

3

33 • • 30• 7

• • 5 • • • 10 3 9• • 1 6• 2 1• •

4

25 •

Quadratic curve 17

(σ xx = 0, σ xy = 0)

p0 = 200 lbs/in.

10"

• • • 37 • 8 • 32 • • •29 15" • 6 •24 (σ • • • 21 15 4 20 " 16 • • 11 • 12• •13 2 7• • 8 (u 3 4 • • •5

x

xx

= 0, σ xy = 0)

= 0, u y = 0)

10"

Line of symmetry(u x = 0, σ xy = 0)

Figure P11.2 Solution to Problems 11.2 and 11.5: The specified displacements are: U1 = V1 = 0, U2 = V2 = 0, U3 = V3 = 0, U4 = V4 = 0, U5 = V5 = 0 The specified nonzero forces are: 4 3 y x = F0 = 800 lbs. F25 = − F0 = 600 lbs. F25 5 5 p0 h 4p0 h 2p0 h 4p0 h p0 h y y y y y =− =− =− =− =− , F34 , F35 , F36 , F37 F33 6 6 6 6 6 The connectivity matrix is given by ⎡

⎤

1 ⎢3 [B] = ⎢ ⎣9 Plane stress 12

• 2 cm

•8 1

•

3 11 9 2 7 10 6 5 13 11 4 8 12 7 ⎥ ⎥ 11 19 17 10 15 18 14 ⎦ ... ... ... ...

E1 = E 2 = 69 GPa, ν = 0.333, G = 26 GPa, h = 1 cm 13

•

14

•

1 2

•

4 cm

•9 3

•

15

•

16

4

•

4 cm

t0 = 3 kN/cm2

•

2

• 10 5

•

h

3

•

11

6

•

4 cm

•

7

4

3

Figure P11.3 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

329

Solution to Problems 11.3 and 11.6: The specified displacements are U1 = V1 = 0, U8 = V8 = 0, U12 = V12 = 0 √ The nonzero specified forces are (a = 2 5, cos α = 4/5 and sin α = 3/5) t0 ha t0 ha 4th 0a x cos α, F7y = sin α, F11 cos α = 6 6 6 4th 0a th 0a th 0a y x = = = sin α, F16 cos α, F16 sin α 6 6 6

F7x = y F11

The connectivity matrix is given by ⎡

⎤

1 3 14 12 2 9 13 8 ⎣ [B] = 3 5 16 14 4 10 15 9 ⎦ 5 7 16 6 11 10 × × Problem 11.7: Consider the cantilevered beam of length 6 cm, height 2 cm, thickness 1 cm, and material properties E = 3 × 107 N/cm2 and ν = 0.3, and subjected to a bending moment of 600 N cm at the free end, (as shown in P11.7). Replace the moment by an equivalent distributed force at x = 6 cm, and model the domain by a nonuniform 10 × 4 mesh of linear rectangular elements and quadratic rectangular elements. Identify the special displacements and global forces.

Plane stress 45 M

2 cm

E = 3 × 107 N/cm 2 , ν = 0.3 h = 1 cm, M 0 = 600 N − cm 55

M

44

7

33

M

22

M

11

1

6 cm

M0

h

Figure P11.7 Solution: The specified displacements are: U1 = 0, U6 = V6 = 0, U11 = 0 The specified nonzero forces are at nodes 11, 22, 33, 44 and 55. To calculate the magnitude, assume that the force causing the moment is linear with y: σxx = σ0 PROPRIETARY MATERIAL.

2y b

c The McGraw-Hill Companies, Inc. °

All rights reserved.

330

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

where the origin of the (x, y) coordinate system is taken at node 23, with x coordinate horizontal and y coordinate vertical, and b = 2cm is the dimension along the y−coordinate. Then we have M0 = 6M0 b2

Hence σ0 = x F11 x F22

= =

x F33 =

Z

−b/2 −b/4 −b/2 0

Z

−b/4

b 2

− 2b

σxx y dy =

σ0 b2 6

= 900N/cm2 . Then we can calculate the forces at nodes

−b/4

Z

Z

σxx ψ11 dy

=−

Z

b/4

−b/2

σxx (4y/b + 2)dy −

σxx (4y/b + 1)dy +

σxx (1 + 4y/b)dy = −

Z

Z

5σ0 b = −187.50N 48

0

−b/4 b/4

σxx (4y/b)dy = −

σ0 b σ0 b − = −225 N 12 24

σxx (1 − 4y/b)dy = −

0

σ0 b σ0 + =0N 48 48

x = −F x and F x = −F x . By antisymmetry, we have F44 22 55 11

Problem 11.8: Consider the (“transition”) element shown in Fig. P11.8. Define the generalized displacement vector of the element by {u} = {u1 , v1 , Θ1 , u2 , v2 , u3 , v3 }T and represent the displacement components u and v by b u = ψ1 u1 + ψ2 u2 + ψ3 u3 + ηψ1 θ1 , 2

v = ψ1 v1 + ψ2 v2 + ψ3 v3

where ψ1 is the interpolation function for the beam, and ψ2 and ψ3 are the interpolation functions for nodes 2 and 3: 1 ψ1 = (1 − ξ), 2

1 ψ2 = (1 + ξ)(1 − η), 4

1 ψ3 = (1 + ξ)(1 + η) 4

Derive the stiffness matrix for the element. η

Transition element

v3 u3

3

v1

b

θ1

2

1

h Beam element

ξ

u1 v2

u2

Plane stress element

Figure P11.8 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

331

Solution: The individual beam and plane elasticity (plane stress) element are shown in the figure below. Both the plan stress and beam elements have the same height b (not depicted in the figure below). Let us introduce the following nodal displacement vector: ∆ = {u1 v1 = w2 θ2 = Θ1 u2 v2 u3 v3 }T

y η

w1

η

v4

w2

θ1

u4

u3

3

4

θ2

1

v3

ξ

b

ξ

v1

2

Beam element

1

u1

2

v2

x

u2

h

Plane stress element

The interpolation functions associated with nodes 2 and 3 are those of the plane stress element and they are ψ2 (ξ, η) =

1 (1 + ξ) (1 − η) , 4

ψ3 (ξ, η) =

1 (1 + ξ) (1 + η) 4

(1)

Node 3 of Fig. P11.8 is a beam node that is connected to the plane stress element. Its interpolation function is 1 ψ1 (ξ, η) = (1 − ξ) 2 The finite element approximation of the displacements (ux , uy ) of the transition element are of the form b ux = u1 ψ1 + ηψ1 Θ1 + u2 ψ2 + u3 ψ3 , uy = v1 ψ1 + v2 ψ2 + v3 ψ3 2

(2)

Then Ψ of Eq. (11.4.2) becomes ∙

ψ1 Ψ= 0 ∆ = { u1

0 ψ1 v1

0.5bηψ1 0 Θ1

u2

ψ2 0 v2

0 ψ2 u3

ψ3 0

0 ψ3

T

¸

(3)

v3 }

The coordinate transformation is given by the usual expression, with the coordinates x1 = x4 = 0, x2 = x3 = h, y1 = y2 = 0, and y3 = y4 = b: x=

4 X

xi ψi =

i=1

PROPRIETARY MATERIAL.

4 X h b yi ψi = (1 + η) (1 + ξ) , y = 2 2 i=1 c The McGraw-Hill Companies, Inc. °

All rights reserved.

(4)

332

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Note that the Jacobian matrix and its inverse are J=

" ∂x

∂y ∂ξ ∂y ∂η

∂ξ ∂x ∂η

#

=

∙h

0

2

b 2

0

¸

,

J

−1

=

∙

2 h

0 2 b

0

¸

and the transformation between (x, y) and (ξ, η) is given by ( ∂ψ e )

( ∂ψ e ) i

i

∂x ∂ψie ∂y

−1

= [J]

∂ξ ∂ψie ∂η

=

∙

2 h

0 2 b

0

¸ ( ∂ψie ) ∂ξ ∂ψie ∂η

(5)

Finally, matrix B required to evaluate the stiffness matrix in (11.4.9) can be computed using Eq. (11.4.4): ⎡

∂ ∂x

⎢ B = DΨ = ⎣ 0 ⎡

2 ∂ h ∂ξ

⎢ =⎣ 0

2 ∂ b ∂η ⎡ 1 −h

=⎣ 0 0

∂ ∂y

0

2 ∂ b ∂η 2 ∂ h ∂ξ

0 0 − h1

0

⎤

∂ ∂y ∂ ∂x

∙ ⎥ ψ1 ⎦

0

⎤

∙ ⎥ ψ1 ⎦

0

0 ψ1

0 ψ1

0.5bηψ1 0

0.5bηψ1 0

ψ2 0

ψ2 0 0 ψ2

0 ψ2 ψ3 0

b 1 − 2h η 0 2h (1 − η) 1 0 0 − 2b (1 + ξ) 1 1 1 2 (1 − ξ) − 2b (1 + ξ) 2h (1 − η)

ψ3 0 0 ψ3

0 ψ3

¸

¸

1 2h (1 + η)

0 1 2b (1 + ξ)

⎤

0 1 (1 + ξ) ⎦ 2b 1 2h (1 + η)

(6)

Problem 11.9: Consider a square, isotropic, elastic body of thickness h shown in Fig. P11.9. Suppose that the displacements are approximated by ux (x, y) = (1 − x)yu1x + x(1 − y)u2x ,

uy (x, y) = 0

Assuming that the body is in a plane state of stress, derive the 2 × 2 stiffness matrix for the unit square ½ 1¾ ½ ¾ ux F1 [K] = u2x F2

b =1

a =1

h

Figure P11.9 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

333

Solution: The interpolation functions are ψ1 (x, y) = (1 − x)y, ψ2 = (1 − y)x. Obviously, the 2D element has just 2 nodes (diagonally opposite sides of the unit square) The element stiffness matrix is given by [K] =

∙

¸

(α + β)h 2 −1 , −1 2 6

α=

E E , β= 2 1−ν 2(1 + ν)

Problems 11.10—11.14: For the plane elasticity problems shown in Figs. P11.10— 11.16, give the boundary degrees of freedom and compute the contribution of the specified forces to the nodes. Solution to Problem 11.10: Note that the element is a quadratic element. The distributed force per unit length (along the y−axis) is τ0 = 3h kN/cm, where thickness of the body is h = 1 cm. The specified non-zero nodal loads are (height b = 2 cm) F7y =

τ0 b 4τ0 b τ0 b y y = = = 1, 000N, F11 = 4, 000N, F18 = 1, 000N 6 6 6

The specified nodal displacements are U1 = V1 = U8 = V8 = U12 = V12 = 0

Plane stress 12

• 2 cm

•8 1

•

E1 = E 2 = 69 GPa, ν = 0.333, G = 26 GPa, h = 1 cm 13

•

14

•

1 2

•

15

4

•

4 cm

18

• 10

3

11

6

7

2

•9 3

17

•

•

5

•

h

16

•

•

•

4 cm

•

• •

4 cm 3 kN/cm2

Figure P11.10 Solution to Problem 11.11: This has two parts. For (a), ux = 0 along the vertical line of symmetry and uy = 0 along the horizontal line of symmetry. The specified nonzero forces are computed using the formula FIx = −

p0 h , 2

FJx = −p0 h

where I is an end node, J is an interior node, and h is the element length along the force. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

334

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

(a)

(b)

2.5 in × 1.5 in

p0

8 in 15 in

34

19

• •

11

• •

6

E = 3 × 107 psi, ν = 0.3

Plane stress

42

35 27

1

h = 1 in, p0 = 200 lb/ft

2

3

4

Line of 26 symmetry

16 10

17

18

Quadrant of the domain

5

Line of symmetry

Figure P11.11 For (b), ux = 0 along the vertical line of symmetry (i.e., nodes 18, 26, 34 and 42) and uy = 0 along the horizontal line of symmetry (i.e., nodes 1 through 5). The specified nonzero forces are computed using the formula FIx = −

p0 h , 2

FJx = −p0 h

where I is an end node (I = 1 and 35), J is an interior node (J = 6, 11, 19 and 27), and h is the element length along the force. Solution to Problem 11.12: The specified displacements are obvious from the figure (U1 = V1 = · · · = U9 = V9 = 0). The nonzero specified forces are (h = 0.75 m) y =− F37

0.75p0 y y = −75 kN, F39 = −75 kN = −37.5 kN, F38 2 y y = −75 kN, F41 = −37.5 kN F40

p0 = 100 kN/m 2 37

45

28

36

4 m 19

27

10

18

9 1

3m

h = 1 cm

8m

Plane strain E = 40 GPa, ν = 0.15

Figure P11.12 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

335

Solution to Problem 11.13: By symmetry, the displacement component ux on x = 0 is zero and the displacement component uy on y = 0 is zero. Hence, the known displacements are V1 = V2 = V3 = V4 = 0,

U14 = U15 = U16 = 0

The non-zero known forces are F4x =

p0 hb p0 hb p0 hb x , F8x = , F19 = 4 2 4 y

a • 12 17 • 15• 8 • 11 13 7 10 • • 4 6 14 12•9 • • 1 1 5• • •1

16

2b

2

18

19 • 10 • 6 • 8• 11 7 • 2 1 3 • 4•

9

p0 (psi)

3

x

One quadrant of the domain is used in the finite element analysis (isotropic plate of thickness h)

Figure P11.13 ty = − p0 sin

πs 2c Plane strain

E = 3 × 107 psi, ν = 0.3 h = 1 in, p0 = 200 lb/ft a = 5 in, b = 4 in, c = 3 in

s

b a

y

b x

Rigid walls

c

Figure P11.14

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

336

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Solution to Problem 11.14: The horizontal displacement ux along the line of symmetry must be zero. Both displacement components are zero along the fixed walls. The only nonzero forces are at the five nodes under the sinusoidal load. They can be computed using Z e Fyi =

sb

sa

ty (s)ψie (s) ds

where ψie are the 1-D interpolation functions ψ1 (s) =

sb − s , he

ψ2 (s) =

s − sa he

The following integrals are useful Z

1 sin as ds = − cos as, a

Z

s sin as ds =

1 s sin as − cos as a2 a

We obtain (a = π/2c)

e Fy2

∙

Z

¸

sb p0 sb p0 sb s 1 sin as (sb − s) ds = − − cos as − 2 sin as + cos as he sa he a a a sa ∙ µ ¶ µ ¶ 2 πsa p0 4c πsb 2c πsb πsa − sin − sa cos =− − 2 sin + sb cos he π 2c 2c π 2c 2c µ ¶¸ πsa 2csb πsb − cos − cos π 2c 2c ∙ ¸sb Z sa p0 sb p0 1 s cos as + cos as =− sin as (s − sa ) ds = − sin as − he sa he a2 a a sa ∙ 2µ ¶ µ ¶ πsa p0 4c πsb 2c πsb πsa − sin − sa cos =− sin − sb cos he π 2 2c 2c π 2c 2c µ ¶¸ πsa 2csa πsb − cos + cos π 2c 2c

e Fy1 =−

The global forces are obtained as 1 1 2 , Fy2 = F2y + F1y , ... Fy1 = F1y

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

337

Chapter 12 BENDING OF ELASTIC PLATES

Problem 12.1: Investigate the displacement and slope compatibility of the nonconforming rectangular element CPT(N). Hint: Use the edge connecting nodes 1 and 2 and check if the displacement w and slopes ∂w/∂x and ∂w/∂y are continuous. Solution: Consider the interface 1—2 between element A and element B (see the figure below). The displacement w and slopes θx = ∂w/∂x and θy = ∂w/∂y along this edge are [from Eq. (12.2.24)] w(x, 0) = a1 + a2 x + a5 x2 + a9 x3 ¶ ∂w = a2 + 2a5 x + 3a9 x2 ∂x y=0 µ ¶ ∂w = a3 + a4 x + a7 x2 + a11 x3 ∂y y=0 µ

Since there are four degrees of freedom, (w, θx ) at each node, along the edge 1—2, w is uniquely determined by the four conditions from both elements and therefore it is continuous across the interface. Thus, a1 , a2 , a5 and a9 are uniquely determined in terms of w1 , w2 , θx1 and θx2 . This also implies that θx is also uniquely defined along the interface. This cannot be said about θy since the expression for θy contains 4 constants that are not determined by the four degrees of freedom (w1 , θx1 , w2 , θx2 ). There are only two other conditions, namely (θy1 , θy2 ), available at the two nodes on the interface 1—2, whereas there are 4 constants. Thus, the slope θy normal to the edge 1—2 is not uniquely defined along the edge 1—2.

•

• θ x1

A

1•

•2 B

•

θx2

w1

•

1

•

PROPRIETARY MATERIAL.

w1

2• Displacement

x

From element A

θ y1

From element B

•

1

θ y2

2•

Normal slope

c The McGraw-Hill Companies, Inc. °

All rights reserved.

x

338

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problems 12.2—12.10: For the plate bending problems (CPT and SDT) given in Figs. P12.2—P12.10, give the specified primary and secondary degrees of freedom and their values for the meshes shown. The dashed lines in the figures indicate simply supported boundary conditions Use E, ν, h, a, and b in formulating the data. You are required to give values of the loads for at least a couple of representative loads. Data for all problems : E = 107 psi, ν = 0.33, ρ = 3 × 10−3 slugs/in3 h = 0.2 in, q0 = 600 lb/in

4

•

5 in

Figure P12.2

•2

•1

q0

7

Fixed end

• •

8 y

5

6

•

•

9

•3

x

z

•

10 in

5 in

∂w Solution to Problem 12.2: For CPT, use ∂w ∂x in place of φx and ∂y in place of φy . Use symmetry about x = 0 line. All primary degrees of freedom are zero along the y = 0 line (fixed edge); w = 0 and ∂w ∂x or φx = 0 along the symmetry line (i.e., x = 0 line). Nodal forces at the y = 10 in. line for FSDT are given by q02h at the outside nodes and q0 h at the inner nodes, h is the element length parallel to the x-axis). Thus, we have F7 = F9 = 750 lb and F8 = 1, 500 lb. For CP T (N ) we have (using the load vector of the Euler—Bernoulli beam element) F7 = F9 = 750 lb, F8 = 1, 500 lb, Mx7 = −312.5 lb-in., My8 = 0 lb-in., and Mx9 = 312.5 lb-in.

q( x , y) = q0

Simply supported at x = ± a/2 and under uniform load Use 2×2 mesh for CPT(C)

y a/ 2

• • 11 • • •1

a/ 2

• • • • • 2

• • • • •3

• • • • •

25

• • •b/ 2 • •

x

b/ 2

Figure P12.3 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

339

Solution to Problem 12.3: The specified displacement degrees of freedom are w3 = w6 =w7 = w8 = w9 = 0; θx1 = θx4 = θx7 = θx8 = θx9 = 0 θy1 = θy2 = θy3 = θy6 = θy9 = 0, θxy1 = 0 ∂w For SDT, use φx in place of θx = ∂w ∂x and φy in place of θy = ∂y in place of φy . In SDT, the load vector of uniformly loaded nine-node element can be obtained from the tensor product of the load vectors of 1-D quadratic elements. The load vector of a 1-D quadratic element of length hx with uniform load q0 is

⎧ ⎫ 1 q0 hx ⎨ ⎬ 4 6 ⎩ ⎭

1

Hence the load vector for a nine-node quadratic element with uniform load is ⎧ ⎫

⎧ ⎫

⎡

⎤

1 1 T 1 4 1 q0 hx ⎨ ⎬ hy ⎨ ⎬ q0 hx hy ⎣ 4 4 4 16 4 ⎦ = 6 ⎩ ⎭ 6 ⎩ ⎭ 36 1 1 1 4 1

Thus, for the SDT, the loads at different nodes are (hx = a/4 and hy = b/4) q0 ab 4q0 ab 2q0 ab 4q0 ab q0 ab , F2 = , F3 = , F4 = , F5 = 576 576 576 576 576 4q0 ab 16q0 ab 8q0 ab 16q0 ab 4q0 ab , F7 = , F8 = , F9 = , F10 = F6 = 576 576 576 576 576 2q0 ab 8q0 ab 4q0 ab 8q0 ab 2q0 ab , F12 = , F13 = , F14 = , F15 = F11 = 576 576 576 576 576 F1 =

etc. For the CPT(C) element, the given mesh must be interpreted as a 2 × 2 mesh of four-node elements (a total of nine nodes). The load vector of uniformly loaded four-node element (of sides hx and hy ) can be obtained from the tensor product of the load vectors of 1-D Euler—Bernoulli beam elements. The load vector of an Euler— Bernoulli beam element of length hx with uniform load q0 is (the rotations used in plate bending do not include the negative sign) ⎧ ⎫ 6 ⎪ ⎪ ⎪ ⎪ q0 hx ⎨ hx ⎬ 6 ⎪ 12 ⎪ ⎪ ⎪ ⎩ ⎭

−hx

Hence, the load vector for a four-node Hermite cubic element with uniform load is ⎧ ⎫ 6 ⎪ ⎪ ⎪ ⎪ q0 hx ⎨ hx ⎬ hy 6 ⎪ 12 ⎪ ⎪ ⎪ ⎩ ⎭ 12

−hx

⎧ ⎫T 6 ⎪ ⎪ ⎪ ⎪ ⎨ ⎬

⎡

36 q0 hx hy ⎢ hy 6h x ⎢ = ⎣ 36 ⎪ 6 ⎪ 144 ⎪ ⎪ ⎩ ⎭ −hy −6hx

PROPRIETARY MATERIAL.

6hy hx hy 6hy −hx hy

c The McGraw-Hill Companies, Inc. °

36 6hx 36 −6hx

⎤

−6hy −hx hy ⎥ ⎥ −6hy ⎦ hx hy

All rights reserved.

340

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

The 2 × 2 submatrix of coefficients (there are four such submatrices) correspoind to the four degrees (Qn , Mx , My , Mxy ) of freedom at the node. Thus, at node 1 we have (hx = a/4 and hy = b/4) Q1 =

q0 ab q0 a2 b q0 ab2 q0 a2 b2 , Mx1 = , My1 = , Mxy1 = 64 64 × 24 64 × 24 256 × 144

At node 2 we have Q2 =

72q0 ab 12q0 ab2 , Mx2 = 0, My2 = − , Mxy2 = 0 16 × 144 64 × 144

At node 5, we have Q5 =

4 × 36q0 ab , Mx5 = 0, My5 = 0, Mxy5 = 0 16 × 144

and so on.

⎛x⎞ q( x , y ) = q0 ⎜ ⎟ ⎝a⎠

y

• •6 •1

a

•

•

•

•

•

•

3

•

4

•

2

•

•15 10

•b x

5• b

Simply supported at y = ±b/2 and under linearly varying load

Figure P12.4 Solution to Problem 12.4: The specified primary degrees of freedom in CPT(C) are w1 = w6 = w11 = 0, θy1 = θy6 = θy11 = θy12 = θy13 = θy14 = θy15 = 0 θx1 = θx2 = θx3 = θx4 = θx5 = θx6 = θx11 = 0 For SDT replace θx with φy and θy with φy . As for the load vector, we have a load that varies linearly with the x-ccordinate. On a typical element, the load varies in the natural coordinate system as (see the figure below) 1 1 q(ξ, η) = q1 ψ1 (ξ) + q2 ψ2 (ξ), ψ1 (ξ) = (1 − ξ), ψ2 (ξ) = (1 + ξ) 2 2 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

341

Thus, the load vector components at nodes 1 and 2 of the SDT element are (F4e = F1e and F2e = F4e ) µ

¶

µ

¶

hy q1e hx (q2e − q1e )hx hy q1e hx q2e hx + + = = 2 2 6 2 3 6 µ e ¶ µ ¶ e − q e )h eh e 2(q q q h q h h y x x y x 1 2 1 1 2 hx e + + F2 = = 2 2 6 2 6 3

F1e

For example, we have F1 = 0.5F6 = F11 F2 = 0.5F7 = F12 F3 = 0.5F8 = F13

µ

¶

q0 hy hx hx q0 ab = = 2 6a 384 µ ¶ µ ¶ q0 hy hx hx q0 hy hx hx hx hx q0 ab = + = + 2 3a 2 3a 3a 64 µ ¶ µ ¶ q0 hy hx hx 2hx hx q0 hy 2hx hx 3hx hx + + = + 2 6a 3a 2 3a 6a q0 ab = 32 y

4 3 q2 q1

1

2

x

For the CPT(N) element, the load vector can be computed using the load vector of a Euler—Bernoulli beam element foir linearly varying load (see Example 5.2.1). We have

⎧ ⎪ ⎨

⎫

9hx + 30xa ⎪ ⎬ q0 hx hy hx (2hx + 5xa ) 21h a ⎪ x + 30xa ⎪ ⎩ ⎭ 12 −hx (3hx + 5xa ) ⎡ 6(9hx + 30xa ) q0 hx hy ⎢ 6hx (2hx + 5xa ) = ⎣ 6(21h + 30x ) 12a x a 6hx (3hx + 5xa )

⎧ ⎫ 6 ⎪T ⎪ ⎨ ⎬ hy

⎪ ⎩ 6 ⎪ ⎭

−hy hy (9hx + 30xa ) hy hx (2hx + 5xa ) hy (21hx + 30xa ) hy hx (3hx + 5xa )

6(9hx + 30xa ) −6hx (2hx + 5xa ) 6(21hx + 30xa ) 6hx (3hx + 5xa )

−hy (9hx + 30xa )

hy hx (2hx + 5xa ) ⎥

−hy (21hx + 30xa ) −hy hx (3hx + 5xa )

Hence, the loads at node 1, for example, are Q1 =

9q0 ab q0 a2 b 3q0 ab2 q0 a2 b2 , Mx1 = , My1 = , Mxy1 = 64 128 64 1536

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

⎤

All rights reserved.

⎦

342

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Solution to Problem 12.5: The boundary conditions on the primary variables are w3 = w6 = w9 = 0, θy1 = θy2 = θy3 = 0, θx7 = θy8 = θy9 = 0 The tangential moment Mrθ = 0 can be prescribed only as a multipoint constraint (between Mn and Ms ). The specified forces in SDT are F1 =

Q0 L14 Q0 L14 Q0 L47 Q0 L47 , F4 = + , F7 = 2 2 2 2

where Lij denote the distance between node i and node j of the mesh. The loads for the CPT(N) can be computed using the load vector of the Euler—Bernoulli beam element, where Lij replaces the element length. Q0

Q0 y 9

•

8• 5 a 7 4 •

6

•

•• b •1 •2 •3

x

Simply supported at r = a

Figure P12.5

and under line load at r = b

q0 y 9

•

8• 5 a 7 4 •

6

•

•• b •1 •2 •3

Figure P12.6 PROPRIETARY MATERIAL.

x

Simply supported at r = a and under uniform load c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

343

Solution to Problem 12.6: The boundary conditions on the primary variables are (same as in Problem 12.5) w3 = w6 = w9 = 0, θy1 = θy2 = θy3 = 0, θx7 = θy8 = θy9 = 0 The tangential moment Mrθ = 0 can be prescribed only as multipoint constraints (between Mn and Ms ). The specified forces in SDT are F1 =

q0 A1 q0 A1 q0 A2 q0 A2 q0 (A1 + A2 + A3 + A4 ) , F2 = + , F3 = , F5 = 4 4 4 4 4

and so on. Here Ai denote the areas of the quadrilateral elements. The loads for the CPT(N) can be computed using the load vector definition and they must be evaluated only numerically. q( x , y) = q0

21 •

y 16 •

•

•

11 •

•

a

• •

• 1 •2 •

• •

25

•20

•

•

•

•

•

• •

•

•15

b

•10 •5

x

Simply supported along the slant edge and under uniform load

Figure P12.7 Solution to Problem 12.7: The boundary conditions on the primary variables are wi = θxi = θyi = 0,

for i = 1, 2, . . . , 5 and i = 21, 22, . . . , 25

The tangential moment Mns = 0 along the slant edges can be prescribed only as multipoint constraints. The specified forces in SDT can be obatined by first noting that qie =

q0 Ai , where Ai is the areaf the ith element 4

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

344

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Then the forces can be easily obtained by inspection of the mesh; for example, we have F1 = q11 , F2 = q21 + q12 , F7 = q31 + q42 + q25 + q16 and so on. The loads for the CPT(N) can be computed using the load vector definition and they must be evaluated only numerically.

Solution to Problem 12.8: The boundary conditions on the primary variables are

wi = θxi = θyi = 0, for i = 3, 6, 9; θy1 = θy2 = 0 θx1 = θx4 = θx7 = θx8 = 0; w7 = w8 = 0 q( x , y ) = q0

a = 20 in

• 7 4•

•

1

8• 5

• • 2

9

• 6

• • 3

b = 15 in

E1 = 30 × 106 psi, E2 = 0.75 × 106 psi,

ν 12 = 0.25, G12 = 0.375 × 106 psi h = 2 in, q0 = 100 lb/in

Figure P12.8 The specified forces at the nodes in CPT(N) can be determined as in Problem 12.2. For SDT, they are

F1 =

q0 hx hy q0 hx hy q0 hx hy , F2 = , F4 = , F1 = q0 hx hy 4 2 2

where hx = 5 in. and hy = 3.75 in. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

345

q0

a

y

a

• •6 5 8• • a 7 •4• •1 2• •3 b 9

x

a

Simply supported at y = ± a/2 and under uniform load

Figure P12.9 Solution to Problem 12.10: The boundary conditions on the primary variables are wi = θxi = θyi = 0, for i = 1, 7, 14, 21 θy1 = θy2 = θy3 = θy4 = θy5 = θy6 = 0 The specified forces at the nodes in SDT and CPT(N) can be determined as in Problem 12.8. q0

21

24 cm

•14 • •7 •1

• •8 • 2•

12 cm × 8 cm hole

• • • •9 •10 •11 • • • •4 3•

• •12 • 5•

•27 •20 •13 •6

12 cm

20 cm 40 cm

Under uniform load E = 200 GPa, ν = 0.3 h = 1 cm, q0 = 60 kN/m 2

Figure P12.10

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGrawHill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

Chapter 13 COMPUTER IMPLEMENTATION OF TWO-DIMENSIONAL PROBLEMS

Note that most of the problems may be analyzed using FEM2D. The results obtained from the program should be evaluated for their accuracy in the light of analytical solutions for qualitative understanding of the solution of the problem. New problems can be generated from those given here by changing the problem data, mesh, type of element, etc. For time-dependent problems, the time step and number of time steps should be chosen such that the solution pattern is established or a steady state is reached. When specific material properties are not given, use values such that the solution can be interpreted as the nondimensional solution of the problem. Additional Note: Solutions to only selected problems are included here for two reasons: (1) it will take lot of space to include the computer input data and output files for each of the problem; (2) many problems are similar and there is only a change of data.

Problems 13.1 and 13.2: Investigate the convergence of solutions to Problem 8.18 using 2 × 2, 4 × 4, and 8 × 8 meshes of linear triangular elements, and compare the results (in graphical or tabular form) with the analytical solution. Solution: Input file for the 8 × 8 mesh of triangles is presented in Box 13.1 and the results are summarized in Table 13.1. Table 13.1: Comparison of the finite element solutions u(0, y) with the analytical solution. Triangular elem. y Mesh T2 Mesh T4 Mesh T8 0.125 0.250 0.375 0.500 0.625 0.750 0.875

−− −− −−

−−

0.0797

−−

0.2303

0.2080

−− −− −−

−−

0.4630

−−

0.0355 0.0764 0.1291 0.2015 0.3050 0.4554 0.6758

PROPRIETARY MATERIAL.

Rectangular elem. Mesh R2 Mesh R4 Mesh R8 −− −− −−

−−

0.0703

−−

0.1520

0.1895

−− −− −−

−−

0.4410

−−

0.0343 0.0740 0.1255 0.1969 0.2996 0.4499 0.6716

c The McGraw-Hill Companies, Inc. °

Analytical Solution 0.0351 0.0757 0.1280 0.2002 0.3034 0.4538 0.6746

All rights reserved.

348

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

y

u( x ,b) = sinπ ( x + 0.5a )

8

7 1

6

∂u =0 4 ∂x

u=0

73

81 72

8 5

1

1

5

7

u=0 1

1

6

20

63 54

15

45 36

10

27

b

4

2

18

3

1 1

21 22 23 24 25

9 1

1

2 0.5a

1

3

x

2 × 2 Mesh

1 2 3 4

5

9

1

4 × 4 Mesh

8 × 8 Mesh

Box 13.1: Input data for program FEM2D (shown only for 8 × 8 mesh of triangles). Prob 13.1: Laplace equation on a square (Problem 8.18: 8 by 8 mesh) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 3 1 0 IELTYP,NPE,MESH,NPRNT 8 8 NX,NY 0.0 0.0625 0.0625 0.0625 0.0625 0.0625 0.0625 0.0625 0.0625 X0,DX(I) 0.0 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.125 Y0,DY(I) 25 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 18 1 27 1 36 1 45 1 54 1 63 1 72 1 73 1 74 1 75 1 76 1 77 1 78 1 79 1 80 1 81 1 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 1.0 0.98079 0.92388 0.83147 0.7071 0.55557 0.38268 0.19510 0.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 0.0 0.0 F0, FX, FY

It is clear that meshes of triangular elements give more accurate results for the number of nodes. This is due to the fact that there are two triangles per a rectangle, thereby provides greater flexibility in approximating the solution. Also, note that the solution predicted by triangles converges from the top while that provided by the rectangular elements converges from the bottom. This means that the triangle underestimates the “stiffness” while the rectangular element overestimates it.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

349

Problem 13.5: Investigate the convergence of the solution to Problem 8.23 using 2 × 2, 4 × 4, and 8 × 8 meshes of linear triangular elements and equivalent meshes of quadratic triangular elements. Solution: If FEM2D is to generate the mesh, we must use the total domain. If the mesh can be read in, then one can exploit the diagonal symmetry of the problem. Here we use the option to generate the mesh by the program FEM2D. The input data and partial output for 4 × 4 mesh of quadratic triangular elements is presented in Box 13.5. Box 13.5: Input data and partial output for program FEM2D (shown only for 4 × 4 mesh of quadratic triangles). Prob. 13.5 Laplace equation on a square (Problem 8.18: 4 by 4 T6 mesh) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 6 1 0 IELTYP,NPE,MESH,NPRNT 4 4 NX,NY 0.0 0.25 0.25 0.25 0.25 X0,DX(I) 0.0 0.25 0.25 0.25 0.25 Y0,DY(I) 32 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 18 1 19 1 27 1 28 1 36 1 37 1 45 1 46 1 54 1 55 1 63 1 64 1 72 1 73 1 74 1 75 1 76 1 77 1 78 1 79 1 80 1 81 1 ISPV(I,J) 0.0 0.015625 0.0625 0.140625 0.25 0.390625 0.5625 0.765625 1.0 0.015625 0.875 0.0625 0.75 0.140625 0.625 0.25 0.5 0.390625 0.375 0.5625 0.25 0.765625 0.125 1.0 0.875 0.75 0.625 0.5 0.375 0.25 0.125 0.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 2.0 0.0 0.0 F0, FX, FY Node

11 12 13 14 15 16 17

x

0.12500E+00 0.25000E+00 0.37500E+00 0.50000E+00 0.62500E+00 0.75000E+00 0.87500E+00

PROPRIETARY MATERIAL.

y

0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00

u(x,y)

0.11449E+00 0.19773E+00 0.28288E+00 0.37869E+00 0.48802E+00 0.61111E+00 0.74359E+00

c The McGraw-Hill Companies, Inc. °

All rights reserved.

350

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.6: Repeat Problem 13.5 using rectangular elements. Solution: The input data and partial output for 4 × 4 mesh of quadratic rectagular elements is presented in Box 13.6. Box 13.6: Input data and partial output for program FEM2D (shown only for 4 × 4 mesh of quadratic rectangles). Prob. 13.6 Laplace equation on a square (Problem 8.18: 4 by 4 Q9 mesh) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 2 9 1 0 IELTYP,NPE,MESH,NPRNT 4 4 NX,NY 0.0 0.25 0.25 0.25 0.25 X0,DX(I) 0.0 0.25 0.25 0.25 0.25 Y0,DY(I) 32 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 18 1 19 1 27 1 28 1 36 1 37 1 45 1 46 1 54 1 55 1 63 1 64 1 72 1 73 1 74 1 75 1 76 1 77 1 78 1 79 1 80 1 81 1 ISPV(I,J) 0.0 0.015625 0.0625 0.140625 0.25 0.390625 0.5625 0.765625 1.0 0.015625 0.875 0.0625 0.75 0.140625 0.625 0.25 0.5 0.390625 0.375 0.5625 0.25 0.765625 0.125 1.0 0.875 0.75 0.625 0.5 0.375 0.25 0.125 0.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 2.0 0.0 0.0 F0, FX, FY Node

11 12 13 14 15 16 17 20 21 22 23 24 25 26

x

y

0.12500E+00 0.25000E+00 0.37500E+00 0.50000E+00 0.62500E+00 0.75000E+00 0.87500E+00 0.12500E+00 0.25000E+00 0.37500E+00 0.50000E+00 0.62500E+00 0.75000E+00 0.87500E+00

PROPRIETARY MATERIAL.

0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.12500E+00 0.25000E+00 0.25000E+00 0.25000E+00 0.25000E+00 0.25000E+00 0.25000E+00 0.25000E+00

u(x,y)

0.11646E+00 0.19820E+00 0.28335E+00 0.37888E+00 0.48838E+00 0.61144E+00 0.74492E+00 0.19820E+00 0.29914E+00 0.38343E+00 0.46224E+00 0.54055E+00 0.61861E+00 0.69170E+00

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

351

Problem 13.7: Analyze the axisymmetric problem in Problem 8.26 using 4 × 1 and 8 × 1 linear rectangular elements, and compare the solution with the exact solution. Solution: The input data and partial output for the two meshes are presented in Boxes 13.7(a) and 13.7(b). The exact solution is in the solution to Problem 8.26. The exact values at r = 0.0, 0.005, 0.01, 0.015, and 0.02 are T1 = 150.0, T2 = 146.875, T3 = 137.50, and T4 = 121.875. Box 13.7(a): Input data and partial output for program FEM2D for 4 × 1 mesh of rectangles. Prob 13.7: An axisymmetric problem (4x1 mesh of rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 1 IELTYP,NPE,MESH,NPRNT 4 1 NX, NY 0.0 0.005 0.005 0.005 0.005 X0, DX(I) 0.0 1.0 Y0, DY(1) 2 NSPV 5 1 10 1 ISPV(I,J) 100.0 100.0 VSPV(I) 0 NSSV 0.0 20.0 0.0 A10, A1X, A1Y 0.0 20.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 1.0E07 0.0 F0, FX, FY Node 1 2 3 4 5 6 7 8 9 10

x-coord.

y-coord.

0.00000E+00 0.50000E-02 0.10000E-01 0.15000E-01 0.20000E-01 0.00000E+00 0.50000E-02 0.10000E-01 0.15000E-01 0.20000E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01

PROPRIETARY MATERIAL.

Primary DOF 0.15175E+03 0.14758E+03 0.13786E+03 0.12202E+03 0.10000E+03 0.15175E+03 0.14758E+03 0.13786E+03 0.12202E+03 0.10000E+03

c The McGraw-Hill Companies, Inc. °

All rights reserved.

352

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Box 13.7(b): Input data and partial output for program FEM2D for 8 × 1 mesh of rectangles. Prob 13.7: An axisymmetric problem (8x1 mesh of rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 8 1 NX, NY 0.0 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 X0, DX(I) 0.0 1.0 Y0, DY(1) 2 NSPV 9 1 18 1 ISPV(I,J) 100.0 100.0 VSPV(I) 0 NSSV 0.0 20.0 0.0 A10, A1X, A1Y 0.0 20.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 1.0E07 0.0 F0, FX, FY

Node

x-coord.

y-coord.

Primary DOF

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

0.00000E+00 0.25000E-02 0.50000E-02 0.75000E-02 0.10000E-01 0.12500E-01 0.15000E-01 0.17500E-01 0.20000E-01 0.00000E+00 0.25000E-02 0.50000E-02 0.75000E-02 0.10000E-01 0.12500E-01 0.15000E-01 0.17500E-01 0.20000E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01

0.15053E+03 0.14948E+03 0.14705E+03 0.14310E+03 0.13759E+03 0.13053E+03 0.12191E+03 0.11174E+03 0.10000E+03 0.15053E+03 0.14948E+03 0.14705E+03 0.14310E+03 0.13759E+03 0.13053E+03 0.12191E+03 0.11174E+03 0.10000E+03

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

353

Problem 13.9: Analyze Problem 8.18 for eigenvalues (take c = 1.0), using a 4 × 4 uniform mesh of triangular elements. Calculate the critical time step for a parabolic equation. Solution: The input data file and edited output for the problem are presented in Box 13.9. The critical time step is ∆tcr = 2/920.9 = 2.172 × 10−3 . Box 13.9: Input data and edited output for 4 × 4 mesh of triangles (eigenvalue problem). Prob 13.9: Eigenvalues of 0 2 1 1 12 1 0 3 1 0 4 4 0.0 0.125 0.125 0.125 0.0 0.25 0.25 0.25 13 1 1 2 1 3 1 4 1 5 20 1 21 1 22 1 23 1 24 1.0 0.0 0.0 1.0 0.0 0.0 0.0 0 1.0 0.0 0.0

a Laplace equation (4by4 T3 mesh) ITYPE,IGRAD,ITEM,NEIGN NVALU, NVCTR IELTYP,NPE,MESH,NPRNT NX,NY 0.125 X0,DX(I) 0.25 Y0,DY(I) NSPV 1 10 1 15 1 1 25 1 ISPV(I,J) A10, A1X, A1Y A20, A2X, A2Y A00 ICONV C0, CX, CY

S O L U T I O N : Number of Jacobi iterations ..... NROT = 217 E I G E N V A L U E ( 1) = 0.920904E+03 E I G E N V A L U E ( 2) = 0.869250E+03 E I G E N V A L U E ( 3) = 0.742104E+03 E I G E N V A L U E ( 4) = 0.626822E+03 E I G E N V A L U E ( 5) = 0.496488E+03 E I G E N V A L U E ( 6) = 0.372089E+03 E I G E N V A L U E ( 7) = 0.323778E+03 E I G E N V A L U E ( 8) = 0.198632E+03 E I G E N V A L U E ( 9) = 0.147678E+03 E I G E N V A L U E ( 10) = 0.122005E+03 E I G E N V A L U E ( 11) = 0.634863E+02 E I G E N V A L U E ( 12) = 0.216955E+02 E I G E N V E C T O R : 0.21660E+01 0.19704E+01 0.14881E+01 0.79420E+00 0.30128E+01 0.27839E+01 0.21305E+01 0.11526E+01 0.20937E+01 0.19650E+01 0.15239E+01 0.83579E+00

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

354

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.10: Analyze Problem 8.18 using a 4 × 4 mesh of triangles for transient response. Assume zero initial conditions. Use α = 0.5 and ∆t = 0.001. Investigate the stability of the solution when α = 0.0 and ∆t = 0.0025. The number of time steps should be such that the solution reaches its peak value or a steady state. Solution: From Problem 13.9, it is clear that for 4 × 4 mesh of linear triangles, the critical time step for conditionally stable schemes is ∆tcr = 0.00217. So, we may wish to investigate the instability of the forward difference scheme (α = 0) using ∆t = 0.0025. The results of the forward difference scheme and Crank-Nicolson scheme are included in Figs. 13.10(a) and 13.10(b).

u(0,0.75,t)

(a)

1.0 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -0.6 -0.8 -1.0

α = 0.0, ∆t = 0.0025

0.000

0.50

0.010

0.020

0.030

Time, t

0.40 0.30

(b)

u(0,0.75,t)

0.20

α = 0.5, ∆t = 0.001

0.10 0.00 -0.10

Steady-state is reached at t = 0.21

-0.20 -0.30 -0.40 0.00 0.05 0.10 0.15 0.20 0.25

Time, t

Fig. 13.10: (a) Transient response showing instability of the forward difference scheme. (b) Transient response reaching steady state with CrankNicolson scheme.

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

355

Problem 13.13: Analyze the heat transfer problem in Problem 8.28 using an 8 × 16 mesh of linear triangular elements and an equivalent mesh of linear rectangular elements. Solution: Using the symmetry considerations, we model the 2 × 8 cm domain with 8 × 16 mesh of linear triangles as well as rectangles. The problem has no specified primary variables, one nonzero specified secondary variable at node 117 of heat Q117 = 125 W, and eight elements at the top row have convection boundary. The input files and modified outputs are presented in Boxes 13.13a and 13.13b. 3

2

3

4

256

242 244

1

Element node numbers

1

2

241

•

•

Electric cables (Q0 = 250 W/cm) k x = 10 W/(cm o C), k y = 15 W/(cm o C)

Insulation

Element 121

2 cm

4 cm Computational domain

•

3o

4 cm

4 cm

Mesh of triangles

y

Convection [T∞ = −5 C, β = 5 W/(cm C)] o

• 6 cm

145

153

127

135

109

•117

91

99

73

81

55

63

37

45

19

27

1

9

x

{DX}={0.25, 0.25,…}, {DY}={0.5, 0.5, …}

Box 13.13a: Input data and edited output for 8 × 16 mesh of triangles. Prob 8.28: Heat transfer in a medium with cables (triangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 3 1 0 IELTYP,NPE,MESH,NPRNT 8 16 NX, NY 0.0 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 X0, DX(I) 0.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Y0, DY(I) 0 NSPV 1 NSSV 117 1 ISSV(1,1), ISSV(1,2) 125.0 VSSV(1) 10.0 0.0 0.0 A10, A1X, A1Y 15.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

356

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

(Table 13.13a continued from the previous page) 1 8 242 244 246 248 250 252 254 256 0.0

ICONV NBE 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 0.0

5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 0.0

Node 1 9 18 90 117 126 145 153

-5.0 -5.0 -5.0 -5.0 -5.0 -5.0 -5.0 -5.0

IBE, INOD, BETA, TINF F0, FX, FY

x-coord. 0.00000E+00 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.00000E+00 0.20000E+01

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.50000E+00 0.45000E+01 0.60000E+01 0.65000E+01 0.80000E+01 0.80000E+01

0.15830E+02 0.15837E+02 0.15837E+02 0.16361E+02 0.23163E+02 0.16247E+02 0.71123E+01 0.79344E+01

. Box 13.13b: Partial input data and edited output for 8 × 16 mesh of rectangles. Prob 8.28: Heat transfer in a medium with cables (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IELTYP,NPE,MESH,NPRNT 8 16 NX, NY . . . . . . . . . . . 1 ICONV 8 NBE 121 4 3 5.0 -5.0 122 4 3 5.0 -5.0 123 4 3 5.0 -5.0 124 4 3 5.0 -5.0 125 4 3 5.0 -5.0 126 4 3 5.0 -5.0 127 4 3 5.0 -5.0 128 4 3 5.0 -5.0 IBE, INOD, BETA, TINF 0.0 0.0 0.0 F0, FX, FY Node 1 9 18 90 117 126 145 153

x-coord. 0.00000E+00 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.00000E+00 0.20000E+01

PROPRIETARY MATERIAL.

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.50000E+00 0.45000E+01 0.60000E+01 0.65000E+01 0.80000E+01 0.80000E+01

0.15831E+02 0.15836E+02 0.15836E+02 0.16301E+02 0.24932E+02 0.15532E+02 0.71346E+01 0.78876E+01

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

357

Problem 13.15: Analyze Problem 8.30 for nodal temperatures and heat flow across the boundaries. Use the following data: k = 30 W/(m ◦ C), β = 60 W/(m2 ◦ C), T∞ = 0◦ C, T0 = 100◦ C, q0 = 2 × 105 W/m2 , g0 = 107 W/m 3 , and a = 1 cm. Solution: The input data and partial output are included in Box 13.15. Box 13.15: Input data and edited output for Prob. 8.30. Prob 8.30: Heat transfer in a square region (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 2 2 NX, NY 0.0 0.01 0.01 X0, DX(I) 0.0 0.01 0.01 Y0, DY(I) 3 NSPV 3 1 6 1 9 1 ISPV(I,J) 100.0 100.0 100.0 VSPV(I) 3 NSSV 1 1 4 1 7 1 ISSV(I,J) 1.0E3 2.0E3 1.0E3 VSSV(I) 30.0 0.0 0.0 A10, A1X, A1Y 30.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 1 ICONV 2 NBE 3 3 4 60.0 0.0 4 3 4 60.0 0.0 IBE, INOD, BETA, TINF 1.0E07 0.0 0.0 F0, FX, FY

Node

x-coord.

y-coord.

Primary DOF

1 2 3 4 5 6 7 8 9

0.00000E+00 0.10000E-01 0.20000E-01 0.00000E+00 0.10000E-01 0.20000E-01 0.00000E+00 0.10000E-01 0.20000E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.10000E-01 0.10000E-01 0.10000E-01 0.20000E-01 0.20000E-01 0.20000E-01

0.29706E+03 0.21458E+03 0.10000E+03 0.29598E+03 0.21383E+03 0.10000E+03 0.29215E+03 0.21088E+03 0.10000E+03

x-coord.

y-coord.

0.5000E-02 0.1500E-01 0.5000E-02 0.1500E-01

0.5000E-02 0.5000E-02 0.1500E-01 0.1500E-01

a22(du/dy) -a11(du/dx) -0.2749E+04 -0.1128E+04 -0.1016E+05 -0.4424E+04

PROPRIETARY MATERIAL.

0.2469E+06 0.3426E+06 0.2451E+06 0.3371E+06

Flux Mgntd Orientation 0.2469E+06 0.3426E+06 0.2453E+06 0.3371E+06

c The McGraw-Hill Companies, Inc. °

90.64 90.19 92.37 90.75

All rights reserved.

358

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.17: Analyze Problem 8.35 for nodal temperature and heat flows across the boundary . Take k = 5 W/(m ◦ C). Solution: The input data and partial output are included in Box 13.17. Box 13.17: Input data and edited output for Prob. 8.35. Prob 8.35: Heat transfer in a square region (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 4 2 NX, NY 0.0 0.02 0.02 0.02 0.02 X0, DX(I) 0.0 0.01 0.01 Y0, DY(I) 3 NSPV 1 1 6 1 11 1 ISPV(I,J) 300.0 300.0 300.0 VSPV(I) 0 NSSV 5.0 0.0 0.0 A10, A1X, A1Y 5.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 1 ICONV 10 NBE 1 1 2 40.0 20.0 2 1 2 40.0 20.0 3 1 2 40.0 20.0 4 1 2 40.0 20.0 4 2 3 40.0 20.0 5 3 4 40.0 20.0 6 3 4 40.0 20.0 7 3 4 40.0 20.0 8 3 4 40.0 20.0 8 3 4 40.0 20.0 IBE, INOD, BETA, TINF 0.0 0.0 0.0 F0, FX, FY Node

x-coord.

y-coord.

Primary DOF

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E-01 0.10000E-01 0.10000E-01 0.10000E-01 0.10000E-01 0.20000E-01 0.20000E-01 0.20000E-01 0.20000E-01 0.20000E-01

0.30000E+03 0.17544E+03 0.11089E+03 0.75481E+02 0.61251E+02 0.30000E+03 0.18415E+03 0.11403E+03 0.77269E+02 0.63053E+02 0.30000E+03 0.17542E+03 0.11112E+03 0.73434E+02 0.59596E+02

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

359

Problem 13.18: Consider heat transfer in a rectangular domain with a central heated circular cylinder (see Fig. P13.19 for the geometry). Analyze the problem using the mesh of linear quadrilateral elements shown in Fig. 13.4.2(b). Solution: The input data and partial output are included in Box 13.18. Box 13.18: Input data and edited output for Problem 13.18. Problem 13.18: Heat transfer from a circular 0 2 0 0 1 4 2 0 16 25 5 1 5 1 0.0 0.0 0.03 0.0 6 10 1 0.0 0.01 0.0307612 0.0038268 11 15 1 0.0 0.02 0.0329289 0.007071 16 20 1 0.02 0.02 0.0361732 0.0092388 21 25 1 0.04 0.02 0.04 0.01 4 1 4 1 1 4 1 2 7 6 5 8 1 1 4 6 7 12 11 9 12 1 1 4 11 12 17 16 13 16 1 1 4 16 17 22 21 3 1 1 6 1 11 1 300.0 300.0 300.0 0 10.0 0.0 0.0 10.0 0.0 0.0 0.0 1 4 4 2 3 40.0 20.0 8 2 3 40.0 20.0 12 2 3 40.0 20.0 16 2 3 40.0 20.0 0.0 0.0 0.0 Node 2 3 4 5 8 9 10 15 20 21 22 23 24 25

x-coord. 0.12857E-01 0.22143E-01 0.27857E-01 0.30000E-01 0.22705E-01 0.28564E-01 0.30761E-01 0.32929E-01 0.36173E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.40000E-01

PROPRIETARY MATERIAL.

cylinder ITYPE,IGRAD,ITEM,NEIGN IELTYP,NPE,MESH,NPRNT NEM, NNM NRECL 6.0 NOD1,NODL,NODINC, ... 6.0 6.0 6.0 6.0 NRECEL NEL1,NELL,IELINC, NODINC

NSPV ISPV(I,J) VSPV(I) NSSV A10, A1X, A1Y A20, A2X, A2Y A00 ICONV NBE

IBE, INOD, BETA, TINF F0, FX, FY

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.54436E-02 0.42677E-02 0.38268E-02 0.70710E-02 0.92388E-02 0.20000E-01 0.15714E-01 0.12619E-01 0.10714E-01 0.10000E-01

0.28987E+03 0.28229E+03 0.27717E+03 0.27506E+03 0.28200E+03 0.27678E+03 0.27456E+03 0.27334E+03 0.27190E+03 0.27365E+03 0.27354E+03 0.27255E+03 0.27141E+03 0.27084E+03

c The McGraw-Hill Companies, Inc. °

All rights reserved.

360

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.19: Analyze the heat transfer problem in Fig. P8.31 with (a) 2 × 2 and (b) 4 × 4 meshes of linear rectangular elements. Solution: The input data and partial output are included in Box 13.19. Box 13.19: Input data and edited output for Problem 13.19. Prob 8.31: Heat transfer in a square region (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 2 2 NX, NY 0.0 0.15 0.15 X0, DX(I) 0.0 0.15 0.15 Y0, DY(I) 5 NSPV 1 1 2 1 3 1 6 1 9 1 ISPV(I,J) 10.0 10.0 40.0 40.0 40.0 VSPV(I) 0 NSSV 5.0 0.0 0.0 A10, A1X, A1Y 5.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 1 ICONV 2 NBE 1 1 4 28.0 0.0 3 1 4 28.0 0.0 IBE, INOD, BETA, TINF 0.0 0.0 0.0 F0, FX, FY k = 5 W/(m oC), β = 28 W/(m 2 oC)

S O L U T I O N :

T∞ = 0 oC, T3 = T6 = T9 = 40 oC,

Node 1 2 3 4 5 6 7 8 9

x-coord. 0.00000E+00 0.15000E+00 0.30000E+00 0.00000E+00 0.15000E+00 0.30000E+00 0.00000E+00 0.15000E+00 0.30000E+00

The orientation of

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.15000E+00 0.15000E+00 0.15000E+00 0.30000E+00 0.30000E+00 0.30000E+00

0.10000E+02 0.10000E+02 0.40000E+02 0.10681E+02 0.23618E+02 0.40000E+02 0.13055E+02 0.25207E+02 0.40000E+02

T1 = T2 = 10 oC, a = 0.15 m Insulated 8

y 7 3

β , T∞ 4

4

6

5

2a

2

1

1 1

9

2

3

x

2a

gradient vector is measured fromthe positive x-axis

x-coord.

y-coord.

a22(du/dy)

-a11(du/dx)

Flux Mgntd

Orientation

0.7500E-01 0.2250E+00 0.7500E-01 0.2250E+00

0.7500E-01 0.7500E-01 0.2250E+00 0.2250E+00

0.2383E+03 0.2270E+03 0.6604E+02 0.2648E+02

-0.2156E+03 -0.7730E+03 -0.4181E+03 -0.5196E+03

0.3214E+03 0.8057E+03 0.4233E+03 0.5203E+03

-42.14 -73.64 -81.02 -87.08

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

361

Problem 13.21: Analyze the problem in Fig. P8.32 with (a) 3 × 3, and (b) 6 × 6 meshes of linear rectangular elements. Take k = 10 W/(m ◦ C). Solution: The input data and partial output are included in Box 13.21. Box 13.21: Input data and edited output for Problem 13.21. Prob 8.32: Heat transfer in a square region (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 3 3 NX, NY 0.0 0.333333 0.333333 0.333333 X0, DX(I) 0.0 0.333333 0.333333 0.333333 Y0, DY(I) 12 NSPV 1 1 2 1 3 1 4 1 5 1 8 1 y 9 1 12 1 13 1 14 1 15 1 16 1 T = 0o C 16 250.0 250.0 250.0 250.0 150.0 50.0 •13 • • • 150.0 50.0 150.0 0.0 0.0 50.0 9 1m 0 9 • • • 12• 10.0 0.0 0.0 o 4 T = 50o C T = 150 C 10.0 0.0 0.0 8 5 • • • • 0.0 k = 10 W/(m oC) 1 2 0 3 3 1 2 g0 = 0 W/m 0.0 0.0 0.0 x • 3• 4• • 1m

Node 6 7 8 9 10 11 12 13 14 15 16

x-coord. 0.33333E+00 0.66667E+00 0.10000E+01 0.00000E+00 0.33333E+00 0.66667E+00 0.10000E+01 0.00000E+00 0.33333E+00 0.66667E+00 0.10000E+01

y-coord.

Primary DOF

0.33333E+00 0.33333E+00 0.33333E+00 0.66667E+00 0.66667E+00 0.66667E+00 0.66667E+00 0.10000E+01 0.10000E+01 0.10000E+01 0.10000E+01

0.17222E+03 0.15000E+03 0.50000E+02 0.15000E+03 0.10556E+03 0.72222E+02 0.50000E+02 0.15000E+03 0.00000E+00 0.00000E+00 0.50000E+02

T = 250o C

x-coord.

y-coord.

a22(du/dy)

-a11(du/dx)

Flux Mgntd

0.1667E+00 0.5000E+00 0.8333E+00 0.1667E+00 0.5000E+00 0.8333E+00 0.1667E+00 0.5000E+00 0.8333E+00

0.1667E+00 0.1667E+00 0.1667E+00 0.5000E+00 0.5000E+00 0.5000E+00 0.8333E+00 0.8333E+00 0.8333E+00

-0.2667E+04 -0.2667E+04 -0.4500E+04 -0.1000E+04 -0.2167E+04 -0.1167E+04 -0.1583E+04 -0.2667E+04 -0.1083E+04

-0.3333E+03 0.3333E+03 0.1500E+04 0.3333E+03 0.8333E+03 0.1833E+04 0.2917E+04 0.5000E+03 -0.4167E+03

0.2687E+04 0.2687E+04 0.4743E+04 0.1054E+04 0.2321E+04 0.2173E+04 0.3319E+04 0.2713E+04 0.1161E+04

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

Orientation -172.87 172.87 161.57 161.57 158.96 122.47 118.50 169.38 -158.96

All rights reserved.

362

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

13.24 Analyze the problem in Fig. P8.35 for transient response using (a) α = 0 and (b) α = 0.5. Use c = ρcp = 1.0. Solution: In order to determine the critical time step, first we find the eigenvalues of the problem. The input data files and partial output for the eigenvalue and transient analysis are included in Boxes 13.24a and 13.24b. Box 13.24a: Input data and edited output for the eigenvalue analysis of Problem 13.24.

T = T0

Prob 8.35a: Eigenvalues of Problem 8.35 (rectangles) 0 2 1 1 ITYPE,IGRAD,ITEM,NEIGN 12 0 NVALU, NVCTR 1 4 1 2 IELTYP,NPE,MESH,NPRNT 4 2 NX, NY 0.0 0.02 0.02 0.02 0.02 X0, DX(I) 0.0 0.01 0.01 Y0, DY(I) 3 NSPV 1 1 6 1 11 1 ISPV(I,J) 5.0 0.0 0.0 A10, A1X, A1Y 5.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 1 ICONV 10 NBE 1 1 2 40.0 20.0 Convection β , T∞ 2 1 2 40.0 20.0 14 11 13 15 12 3 1 2 40.0 20.0 5 6 7 8 4 1 2 40.0 20.0 6 7 8 9 4 2 3 40.0 20.0 10 1 3 2 4 5 3 4 40.0 20.0 1 2 3 4 5 6 3 4 40.0 20.0 Convection β , T∞ a = 2 cm 7 3 4 40.0 20.0 8 3 4 40.0 20.0 8 3 4 40.0 20.0 IBE, INOD, BETA, TINF 1.0 0.0 0.0 C0, CX, CY S O L U T I O N :

∆tcr =

2

λmax

= 2.67 × 10 −6

Number of Jacobi iterations ..... NROT = 178 E E E E E E E E E E E E

I I I I I I I I I I I I

G G G G G G G G G G G G

E E E E E E E E E E E E

N N N N N N N N N N N N

V V V V V V V V V V V V

A A A A A A A A A A A A

L L L L L L L L L L L L

PROPRIETARY MATERIAL.

U U U U U U U U U U U U

E E E E E E E E E E E E

( 1) = ( 2) = ( 3) = ( 4) = ( 5) = ( 6) = ( 7) = ( 8) = ( 9) = ( 10) = ( 11) = ( 12) =

0.750377E+06 0.678560E+06 0.634478E+06 0.616934E+06 0.300201E+06 0.228506E+06 0.184303E+06 0.166798E+06 0.140265E+06 0.694258E+05 0.246351E+05 0.716251E+04

c The McGraw-Hill Companies, Inc. °

All rights reserved.

1 cm β , T∞

SOLUTIONS MANUAL

363

Box 13.24b: Input data and edited output for the transient analysis of Problem 13.24.

T = T0

Prob 8.35b: Transient analysis of Problem 8.35 (rectangles) 0 2 1 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IELTYP,NPE,MESH,NPRNT 4 2 NX, NY 0.0 0.02 0.02 0.02 0.02 X0, DX(I) 0.0 0.01 0.01 Y0, DY(I) 3 NSPV 1 1 6 1 11 1 ISPV(I,J) 300.0 300.0 300.0 VSPV(I) 0 NSSV 5.0 0.0 0.0 A10, A1X, A1Y 5.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 1 ICONV 10 NBE 1 1 2 40.0 20.0 Convection β , T∞ 2 1 2 40.0 20.0 14 11 13 15 3 1 2 40.0 20.0 12 1 cm 5 6 7 8 4 1 2 40.0 20.0 6 7 8 9 4 2 3 40.0 20.0 β , T∞ 10 1 3 2 4 5 3 4 40.0 20.0 1 2 3 4 5 6 3 4 40.0 20.0 Convection β , T∞ a = 2 cm 7 3 4 40.0 20.0 8 3 4 40.0 20.0 8 3 4 40.0 20.0 IBE, INOD, BETA, TINF 0.0 0.0 0.0 F0, FX, FY 1.0 0.0 0.0 C0, CX, CY 500 501 10 0 NTIME,NSTP,INTVL,INTIAL 1.0E-06 0.0 0.5 1.0E-4 DT,ALFA,GAMA,EPSLN

*TIME* = 0.10000E-05 Node 1 2 3 4 5 10 15

x-coord. 0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01

0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01

PROPRIETARY MATERIAL.

1

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E-01 0.20000E-01

0.30000E+03 -0.80008E+02 0.21954E+02 -0.58868E+01 0.36334E+01 0.29023E+01 0.37299E+01

*TIME* = 0.10000E-04 1 2 3 4 5 10 15

Time Step Number =

Time Step Number = 10

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E-01 0.20000E-01

0.30000E+03 -0.74458E+01 -0.63061E+01 0.39980E+01 0.62873E+00 -0.38760E+00 0.11335E+01

c The McGraw-Hill Companies, Inc. °

All rights reserved.

364

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

(Box 13.24b is continued from the previous page; α = 0) *TIME* 1 2 3 4 5 10 15

= 0.40000E-04 0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01

Time Step 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.10000E-01 0.20000E-01

Number = 40 0.30000E+03 0.86300E+02 0.74688E+01 0.72856E+00 0.55114E+01 0.48108E+01 0.60875E+01

*TIME* = 0.10000E-03 Time Step Number =100 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.13695E+03 3 0.40000E-01 0.00000E+00 0.52757E+02 4 0.60000E-01 0.00000E+00 0.17355E+02 5 0.80000E-01 0.00000E+00 0.10216E+02 10 0.80000E-01 0.10000E-01 0.96855E+01 15 0.80000E-01 0.20000E-01 0.10433E+02 *TIME* = 0.20000E-03 Time Step Number =200 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.16020E+03 3 0.40000E-01 0.00000E+00 0.84988E+02 4 0.60000E-01 0.00000E+00 0.45326E+02 5 0.80000E-01 0.00000E+00 0.32576E+02 10 0.80000E-01 0.10000E-01 0.33055E+02 15 0.80000E-01 0.20000E-01 0.31928E+02 *TIME* = 0.30000E-03 Time Step Number =300 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.16830E+03 3 0.40000E-01 0.00000E+00 0.98472E+02 4 0.60000E-01 0.00000E+00 0.60636E+02 5 0.80000E-01 0.00000E+00 0.46961E+02 10 0.80000E-01 0.10000E-01 0.48102E+02 15 0.80000E-01 0.20000E-01 0.45804E+02 *TIME* = 0.40000E-03 Time Step Number =400 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.17199E+03 3 0.40000E-01 0.00000E+00 0.10486E+03 4 0.60000E-01 0.00000E+00 0.68234E+02 5 0.80000E-01 0.00000E+00 0.54261E+02 10 0.80000E-01 0.10000E-01 0.55740E+02 15 0.80000E-01 0.20000E-01 0.52850E+02 *TIME* = 0.50000E-03 Time Step Number =500 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.17376E+03 3 0.40000E-01 0.00000E+00 0.10795E+03 4 0.60000E-01 0.00000E+00 0.71948E+02 5 0.80000E-01 0.00000E+00 0.57842E+02 10 0.80000E-01 0.10000E-01 0.59487E+02 15 0.80000E-01 0.20000E-01 0.56307E+02

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

(Box 13.24b is continued from the previous two pages; α = 0.5) *TIME* 1 2 3 4 5 10 15

= 0.10000E-05 0.00000E+00 0.20000E-01 0.40000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01

Time Step Number = 1 0.00000E+00 0.30000E+03 0.00000E+00 -0.75048E+02 0.00000E+00 0.19257E+02 0.00000E+00 -0.48145E+01 0.00000E+00 0.28232E+01 0.10000E-01 0.22798E+01 0.20000E-01 0.29189E+01

*TIME* = 0.10000E-04 Time Step Number = 10 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 -0.61555E+01 3 0.40000E-01 0.00000E+00 -0.56611E+01 4 0.60000E-01 0.00000E+00 0.35382E+01 5 0.80000E-01 0.00000E+00 0.90864E+00 10 0.80000E-01 0.10000E-01 -0.10142E+00 15 0.80000E-01 0.20000E-01 0.13939E+01 *TIME* = 0.10000E-03 Time Step Number =100 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.13679E+03 3 0.40000E-01 0.00000E+00 0.52687E+02 4 0.60000E-01 0.00000E+00 0.17478E+02 5 0.80000E-01 0.00000E+00 0.10408E+02 10 0.80000E-01 0.10000E-01 0.98865E+01 15 0.80000E-01 0.20000E-01 0.10619E+02 *TIME* = 0.20000E-03 Time Step Number =200 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.16014E+03 3 0.40000E-01 0.00000E+00 0.84912E+02 4 0.60000E-01 0.00000E+00 0.45283E+02 5 0.80000E-01 0.00000E+00 0.32556E+02 10 0.80000E-01 0.10000E-01 0.33034E+02 15 0.80000E-01 0.20000E-01 0.31909E+02 *TIME* = 0.30000E-03 Time Step Number =300 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.16826E+03 3 0.40000E-01 0.00000E+00 0.98412E+02 4 0.60000E-01 0.00000E+00 0.60570E+02 5 0.80000E-01 0.00000E+00 0.46900E+02 10 0.80000E-01 0.10000E-01 0.48039E+02 15 0.80000E-01 0.20000E-01 0.45746E+02 *TIME* = 0.50000E-03 Time Step Number =500 1 0.00000E+00 0.00000E+00 0.30000E+03 2 0.20000E-01 0.00000E+00 0.17374E+03 3 0.40000E-01 0.00000E+00 0.10793E+03 4 0.60000E-01 0.00000E+00 0.71914E+02 5 0.80000E-01 0.00000E+00 0.57809E+02 10 0.80000E-01 0.10000E-01 0.59452E+02 15 0.80000E-01 0.20000E-01 0.56275E+02

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

365

366

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

13.25 Analyze the axisymmetric problem in Fig. P8.26 using the Crank—Nicolson method. Use an 8 × 1 mesh of linear rectangular elements and c = ρcp = 3.6 × 106 J/(m3 ·K). Solution: The eigenvalue analysis gives ∆tcr = 0.1698. Input data and partial output are included in Boxes 13.25a and 13.25b. Box 13.25a: Input data and edited output for the eigenvalue analysis of Problem 13.25. Prob 8.26a Eigenvalue of an axisymmetric problem 0 2 1 1 ITYPE,IGRAD,ITEM,NEIGN 16 0 1 4 1 2 IELTYP,NPE,MESH,NPRNT 8 1 NX, NY 0.0 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 X0, DX(I) 0.0 1.0 Y0, DY(1) 2 NSPV 9 1 18 1 ISPV(I,J) 0.0 20.0 0.0 A10, A1X, A1Y 0.0 20.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0. 3.6E06 0.0 C0, CX, CY S O L U T I O N : Number of Jacobi iterations ..... NROT = 225 E E E E E E E E E E E E E E E E

I I I I I I I I I I I I I I I I

G G G G G G G G G G G G G G G G

E E E E E E E E E E E E E E E E

N N N N N N N N N N N N N N N N

V V V V V V V V V V V V V V V V

A A A A A A A A A A A A A A A A

L L L L L L L L L L L L L L L L

U U U U U U U U U U U U U U U U

∆tcr =

PROPRIETARY MATERIAL.

E E E E E E E E E E E E E E E E

( ( ( ( ( ( ( ( ( ( ( ( ( ( ( (

1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16)

= = = = = = = = = = = = = = = =

0.117769E+02 0.117768E+02 0.893008E+01 0.389702E+01 0.620594E+01 0.893014E+01 0.620601E+01 0.389696E+01 0.112116E+01 0.223250E+01 0.223256E+01 0.434475E+00 0.112109E+01 0.434542E+00 0.804288E-01 0.804954E-01

2 = 0.1698 11.7769

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

367

Box 13.25b: Input data and edited output for the transient analysis of Problem 13.25. Prob 8.26b Transient analysis of an axisymmetric problem 0 2 1 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IELTYP,NPE,MESH,NPRNT 8 1 NX, NY 0.0 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 0.0025 X0, DX(I) 0.0 1.0 Y0, DY(1) 2 NSPV 9 1 18 1 ISPV(I,J) 100.0 100.0 VSPV(I) 0 NSSV 0.0 20.0 0.0 A10, A1X, A1Y 0.0 20.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 1.0E07 0.0 F0, FX, FY 0.0 3.6E06 0.0 C0, CX, CY 500 501 10 0 NTIME,NSTP,INTVL,INTIAL 0.2 0.5 0.5 1.0E-5 DT,ALFA,GAMA,EPSLN *TIME* = 0.10000E+02

Time Step Number = 50

Node

x-coord.

y-coord.

Primary DOF

1 2 3 4 5 6 7 8 9

0.00000E+00 0.25000E-02 0.50000E-02 0.75000E-02 0.10000E-01 0.12500E-01 0.15000E-01 0.17500E-01 0.20000E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00

0.53769E+02 0.55406E+02 0.59123E+02 0.64867E+02 0.72184E+02 0.80371E+02 0.88488E+02 0.95424E+02 0.10000E+03

*TIME* = 0.90000E+02 1 2 3 4 5 6 7 8 9

0.00000E+00 0.25000E-02 0.50000E-02 0.75000E-02 0.10000E-01 0.12500E-01 0.15000E-01 0.17500E-01 0.20000E-01

Time Step Number =450 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00

0.15037E+03 0.14933E+03 0.14691E+03 0.14297E+03 0.13749E+03 0.13045E+03 0.12186E+03 0.11171E+03 0.10000E+03

Reached steady-state at this time

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

368

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.27: Repeat Problem 13.26 with the mesh of linear triangular elements shown in Fig. 8.3.8. Solution: Input data and partial output are included in Boxes 13.27a and 13.27b, respectively. Box 13.27a: Input data for the ground water flow problem of Problem 13.27. Problem 13.27: Ground water flow problem (triangles) 0 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 3 2 1 IELTYP,NPE,MESH,NPRNT 64 45 NEM,NNM 9 NRECL 1 5 1 0.0 0.0 600.0 0.0 1.0 NOD1,NODL,... 6 10 1 0.0 87.5 600.0 175.0 1.0 11 15 1 0.0 175.0 600.0 350.0 1.0 16 20 1 0.0 262.5 600.0 525.0 1.0 21 25 1 0.0 350.0 600.0 700.0 1.0 26 30 1 0.0 525.0 600.0 787.5 1.0 31 35 1 0.0 700.0 600.0 875.0 1.0 36 40 1 0.0 875.0 600.0 962.5 1.0 41 45 1 0.0 1050.0 600.0 1050.0 1.0 16 NRECEL 1 7 2 1 3 1 2 6 NEL1,NELL,IELINC,NODINC,.. 2 8 2 1 3 2 7 6 9 15 2 1 3 6 7 11 10 16 2 1 3 7 12 11 17 23 2 1 3 11 12 16 18 24 2 1 3 12 17 16 25 31 2 1 3 16 17 21 26 32 2 1 3 17 22 21 33 39 2 1 3 21 22 26 34 40 2 1 3 22 27 26 41 47 2 1 3 26 27 31 42 48 2 1 3 27 32 31 49 55 2 1 3 31 32 36 50 56 2 1 3 32 37 36 57 63 2 1 3 36 37 41 58 64 2 1 3 37 42 41 5 NSPV 41 1 42 1 43 1 44 1 45 1 ISPV 100.0 100.0 100.0 100.0 100.0 VSPV 6 NSSV 21 1 22 1 23 1 24 1 25 1 33 1 ISSV(I,J) 45.069 90.139 90.139 90.139 45.069 -200.0 VSSV(I) 1.75 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 0.0 0.0 F0, FX, FY

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

y

Impermeable,

∂φ =0 ∂n

a11 = 1.75 m3/day/m2 , a22 = 1 m3/day/m2

400 m

x

φ = 100 m

3

Impermeable, ∂φ =0 ∂n

2

(300, 787.5)

Pump Q = 200 m3/day

•

Stream q = 0.5 m3/day/m

Impermeable,

369

∂φ =0 ∂n

b = 600 m

200 m

a = 1050 m

Box 13.27b: Edited output for the ground water flow problem of Problem 13.27.

Node 1 2 3 4 5 10 15 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

x-coord. 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03 0.60000E+03 0.60000E+03 0.60000E+03 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03 0.00000E+00 0.15000E+03 0.30000E+03 0.45000E+03 0.60000E+03

PROPRIETARY MATERIAL.

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.17500E+03 0.35000E+03 0.52500E+03 0.35000E+03 0.43750E+03 0.52500E+03 0.61250E+03 0.70000E+03 0.52500E+03 0.59063E+03 0.65625E+03 0.72188E+03 0.78750E+03 0.70000E+03 0.74375E+03 0.78750E+03 0.83125E+03 0.87500E+03 0.87500E+03 0.89688E+03 0.91875E+03 0.94063E+03 0.96250E+03 0.10500E+04 0.10500E+04 0.10500E+04 0.10500E+04 0.10500E+04

0.33097E+03 0.32998E+03 0.32788E+03 0.32598E+03 0.32523E+03 0.32330E+03 0.31538E+03 0.29556E+03 0.35206E+03 0.33574E+03 0.31120E+03 0.28367E+03 0.25282E+03 0.29531E+03 0.26855E+03 0.23939E+03 0.21890E+03 0.19783E+03 0.21492E+03 0.19083E+03 0.14004E+03 0.16513E+03 0.15799E+03 0.14902E+03 0.13931E+03 0.13034E+03 0.13121E+03 0.12729E+03 0.10000E+03 0.10000E+03 0.10000E+03 0.10000E+03 0.10000E+03

c The McGraw-Hill Companies, Inc. °

All rights reserved.

370

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.31: Analyze the flow around cylinder of elliptical cross-section (see Fig. P8.41). Use the symmetry and an appropriate mesh of linear triangular elements. Use the stream function approach. Solution: Here we use the mesh of linear triangles from Fig. 8.5.10. Input data and partial output are included in Boxes 13.31a and 13.31b, respectively. Box 13.31a: Input data for the flow around an elliptic cylinder of Problem 13.31. Prob 13.31: Flow around an elliptic cylinder (Stream function-Triangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 3 2 1 IELTYP,NPE,MESH,NPRNT 60 42 NEM, NNM 7 NRECL 1 6 1 0.0 0.0 3.0 0.0 0.3164 NOD1,NODL,... 7 12 1 0.0 0.6667 3.034074 0.12941 0.3164 13 18 1 0.0 1.3333 3.133975 0.25 0.3164 19 24 1 0.0 2.0 3.292893 0.35355 0.3164 25 30 1 1.3333 2.0 3.5 0.4330 0.3164 31 36 1 2.6667 2.0 3.74118 0.48296 0.3164 37 42 1 4.0 2.0 4.0 0.5 0.3164 12 NRECEL 1 9 2 1 3 1 2 8 NEL1,NELL,IELINC,NODINC 2 10 2 1 3 1 8 7 11 19 2 1 3 7 8 14 12 20 2 1 3 7 14 13 21 29 2 1 3 13 14 20 22 30 2 1 3 13 20 19 31 39 2 1 3 19 20 25 32 40 2 1 3 20 26 25 41 49 2 1 3 25 26 31 42 50 2 1 3 26 32 31 51 59 2 1 3 31 32 37 52 60 2 1 3 32 38 37 18 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 12 1 18 1 24 1 30 1 36 1 42 1 7 1 13 1 19 1 25 1 31 1 37 1 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.6667 1.3333 2.0 2.0 2.0 2.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 0.0 0.0 0.0 F0, FX, FY

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

371

Fixed wall (no flow)

u0 = 1

u0 = 1 1 cm

b = 4 cm

2 cm

a = 8 cm

Fixed wall (no flow)

Box 13.31b: Edited output for the flow around an elliptic cylinder of Problem 13.31. S O L U T I O N : Node

x-coord.

y-coord.

Primary DOF

7 8 9 10 11 13 14 15 16 17 19 20 21 22 23 26 27 28 29 32 33 34 35 38 39 40 41

0.00000E+00 0.29170E+00 0.74096E+00 0.13478E+01 0.21121E+01 0.00000E+00 0.30130E+00 0.76535E+00 0.13921E+01 0.21817E+01 0.00000E+00 0.31658E+00 0.80416E+00 0.14627E+01 0.22923E+01 0.15416E+01 0.18624E+01 0.22958E+01 0.28416E+01 0.27700E+01 0.29291E+01 0.31440E+01 0.34147E+01 0.40000E+01 0.40000E+01 0.40000E+01 0.40000E+01

0.66670E+00 0.61504E+00 0.53549E+00 0.42803E+00 0.29267E+00 0.13333E+01 0.12292E+01 0.10687E+01 0.85209E+00 0.57917E+00 0.20000E+01 0.18417E+01 0.15979E+01 0.12686E+01 0.85384E+00 0.18493E+01 0.16173E+01 0.13039E+01 0.90915E+00 0.18542E+01 0.16295E+01 0.13261E+01 0.94393E+00 0.18558E+01 0.16337E+01 0.13337E+01 0.95579E+00

0.66670E+00 0.61367E+00 0.53175E+00 0.41956E+00 0.27278E+00 0.13333E+01 0.12276E+01 0.10635E+01 0.83773E+00 0.53821E+00 0.20000E+01 0.18415E+01 0.15949E+01 0.12537E+01 0.79541E+00 0.18450E+01 0.16001E+01 0.12524E+01 0.74952E+00 0.18330E+01 0.15691E+01 0.11951E+01 0.68802E+00 0.18217E+01 0.15440E+01 0.11610E+01 0.65865E+00

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

372

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.33: Analyze the torsion of a member of circular cross-section (see Fig. P8.43) for the state of shear stress distribution. Investigate the accuracy with mesh refinements (by subdividing the mesh in Fig. P8.43 with horizontal and vertical lines). Solution: Here we use the mesh of linear triangles from Fig. P8.43. Input data and partial output are included in Boxes 13.33a and 13.33b, respectively. Box 13.33a: Input data for the circular cross-section bar of Problem 13.33. Prob 8.43: Torsion of a circular cross-section bar (triangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 0 3 0 2 IELTYP,NPE,MESH,NPRNT 4 6 NEM, NNM 1 2 4 2 3 5 2 5 4 4 5 6 NOD(I,J) 0.0 0.0 0.5 0.0 1.0 0.0 0.35355 0.35355 0.92388 0.38268 0.7071 0.7071 GLXY(I,J) 3 NSPV 3 1 5 1 6 1 ISPV(I,J) 0.0 0.0 0.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 10.0 0.0 0.0 F0, FX, FY By symmetry, any sector can be used as the computational domain

y

•6 • •5 •1 •2 •3 41

1

a

y

a = 1, 2Gθ = 10

1

3 1 1 2

Mesh of 4 linear triangles

PROPRIETARY MATERIAL.

•15•14 • 12 6 • • •9 •• •• •1 •2 •3 •4 •5 13 10

4

1

x a

1

x

Mesh of 4 quadratic triangles

c The McGraw-Hill Companies, Inc. °

All rights reserved.

373

SOLUTIONS MANUAL

Box 13.33b: Edited output for the circular cross-section bar of Problem 13.33 for two different meshes. S O L U T I O N Node 1 2 3 4 5 6

(for the 4 linear element mesh):

x-coord. 0.00000E+00 0.50000E+00 0.10000E+01 0.35355E+00 0.92388E+00 0.70710E+00

The orientation of

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.35355E+00 0.38268E+00 0.70710E+00

0.26292E+01 0.19179E+01 0.00000E+00 0.19179E+01 0.00000E+00 0.00000E+00

gradient vector is measured from the positive x-axis

x-coord.

y-coord.

a22(du/dy)

-a11(du/dx)

Flux Mgntd

Orientation

0.2845E+00 0.8080E+00 0.5925E+00 0.6615E+00

0.1179E+00 0.1276E+00 0.2454E+00 0.4811E+00

-0.5892E+00 -0.7630E+00 -0.1364E+01 -0.2173E+01

0.1423E+01 0.3836E+01 0.3293E+01 0.3252E+01

0.1540E+01 0.3911E+01 0.3565E+01 0.3911E+01

112.50 101.25 112.50 123.75

S O L U T I O N Node 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

(for the 4 quadratic element mesh):

x-coord. 0.00000E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.10000E+01 0.17677E+00 0.46194E+00 0.73559E+00 0.98078E+00 0.35355E+00 0.62360E+00 0.92388E+00 0.53033E+00 0.83147E+00 0.70711E+00

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.17677E+00 0.19134E+00 0.14632E+00 0.19509E+00 0.35355E+00 0.41668E+00 0.38268E+00 0.53033E+00 0.55557E+00 0.70711E+00

0.24893E+01 0.23481E+01 0.18618E+01 0.10959E+01 0.00000E+00 0.23481E+01 0.18811E+01 0.10960E+01 0.00000E+00 0.18618E+01 0.10960E+01 0.00000E+00 0.10959E+01 0.00000E+00 0.00000E+00

⎡ 1 3 10 2 7 6⎤ ⎢ 3 12 10 8 11 7⎥ ⎥ [ B] = ⎢ ⎢ 3 5 12 4 9 8⎥ ⎢ ⎥ ⎣10 12 15 11 14 13⎦ 15

13 1

10 3

6 1

1

6

1

7

5

4

2 1

2

3

14

4 11 2

12 8

9

3

1

4

5

x-coord.

y-coord.

a22(du/dy)

-a11(du/dx)

Flux Mgntd

Orientation

0.3001E+00 0.6119E+00 0.8268E+00 0.6619E+00

0.1243E+00 0.2535E+00 0.1092E+00 0.5074E+00

-0.6209E+00 -0.1293E+01 -0.5720E+00 -0.2525E+01

0.1499E+01 0.3122E+01 0.4143E+01 0.3334E+01

0.1623E+01 0.3379E+01 0.4182E+01 0.4182E+01

112.50 112.50 97.86 127.14

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

374

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.36: Analyze the rectangular membrane problem in Fig. P8.48 with 4 × 4 and 8 × 8 meshes of linear rectangular elements in the computational domain. Take a11 = a22 = 1 and f0 = 1. Solution: Input data and partial output are included in Box 13.36. Box 13.36: Input data and edited output for the 4 × 4 mesh of linear rectangular elements. Prob 13.36: Deflections of the membrane of Problem 8.48 (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 4 4 NX, NY 0.0 0.0125 0.0125 0.0125 0.0125 DX(I) 0.0 0.02 0.02 0.02 0.02 DY(I) 13 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 11 1 16 1 21 1 22 1 23 1 24 1 25 1 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.109375 0.1875 0.234375 0.25 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 1.0 0.0 0.0 F0, FX, FY

Node 7 8 9 10 12 13 14 15 17 18 19 20 22 23 24 25

x-coord.

y-coord.

0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01

0.20000E-01 0.20000E-01 0.20000E-01 0.20000E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.60000E-01 0.60000E-01 0.60000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01 0.80000E-01

PROPRIETARY MATERIAL.

Primary DOF 0.10669E-01 y u = (10 − x )x ( x is in cm ) 0.19647E-01 5cm 0.25612E-01 0.27705E-01 • • • • •25 0.25698E-01 0.47286E-01 u = 0 • • • • • 20 0.61702E-01 • • • • •15 u=0 0.66745E-01 8 cm 6 0.51737E-01 • • • • •10 0.95449E-01 0.12351E+00 x •1 • • • •5 0.13312E+00 10 cm u = 0 0.10938E+00 0.18750E+00 ∆x = 1.25 cm = 0.0125 m 0.23438E+00 ∆y = 2 cm = 0.02 m 0.25000E+00

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

Problem 13.37: elements.

375

Repeat Problem 13.36 with equivalent meshes of quadratic

Solution: Input data and partial output are included in Box 13.37. Box 13.37: Input data and edited output for the 2 × 2 mesh of nine-node rectangular elements. Prob 13.37: Deflections of the membrane of Problem 8.48 (rectangles) 0 2 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 2 IELTYP,NPE,MESH,NPRNT 4 4 NX, NY 0.0 0.025 0.025 DX(I) 0.0 0.04 0.04 DY(I) 13 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 11 1 16 1 21 1 22 1 23 1 24 1 25 1 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.109375 0.1875 0.234375 0.25 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 1.0 0.0 0.0 F0, FX, FY Node 7 8 9 10 12 13 14 15 17 18 19 20 22 23 24 25

x-coord. 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01 0.12500E-01 0.25000E-01 0.37500E-01 0.50000E-01

y-coord. 0.20000E-01 0.20000E-01 0.20000E-01 0.20000E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.40000E-01 0.60000E-01 0.60000E-01 0.60000E-01 0.60000E-01 0.80000E-01 0.80000E-01 0.80000E-01 0.80000E-01

PROPRIETARY MATERIAL.

Primary DOF 0.11083E-01 y u = (10 − x )x ( x is in cm ) 0.20366E-01 5cm 0.26477E-01 0.28619E-01 • • • • •25 0.26859E-01 0.48751E-01 u = 0 • • • • • 20 0.63252E-01 • • • • •15 u=0 0.68306E-01 8 cm 6 0.53199E-01 • • • • •10 0.97014E-01 0.12487E+00 x •1 • • • •5 0.13443E+00 10 cm u = 0 0.10938E+00 0.18750E+00 ∆x = 2.5 cm = 0.025 m 0.23438E+00 ∆y = 4 cm = 0.04 m 0.25000E+00

c The McGraw-Hill Companies, Inc. °

All rights reserved.

376

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.38: Determine the eigenvalues of the rectangular membrane in Fig. P8.48 using a 4 × 4 mesh of linear rectangular elements in the half-domain. Use c = 1.0. Solution: Input data and partial output are included in Box 13.38. Box 13.38: Input data and edited output for the 4 × 4 mesh of linear rectangular elements. Prob 8.48: Frequencies of a square membrane (rectangles) 0 2 2 1 ITYPE,IGRAD,ITEM,NEIGN 12 0 NVALU, NVCTR 1 4 1 2 IELTYP,NPE,MESH,NPRNT 4 4 NX, NY 0.0 0.0125 0.0125 0.0125 0.0125 DX(I) 0.0 0.02 0.02 0.02 0.02 DY(I) 13 NSPV 1 1 2 1 3 1 4 1 5 1 6 1 11 1 16 1 21 1 22 1 23 1 24 1 25 1 ISPV(I,J) 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 1.0 0.0 0.0 C0, CX, CY S O L U T I O N : Number of Jacobi iterations ..... NROT = 150 Eigenvalue(

1) =

0.884549E+05

Frequency =

0.29741E+03

Eigenvalue(

2) =

0.761512E+05

Frequency =

0.27596E+03

Eigenvalue(

3) =

0.702742E+05

Frequency =

0.26509E+03

Eigenvalue(

4) =

0.526383E+05

Frequency =

0.22943E+03

Eigenvalue(

5) =

0.297534E+05

Frequency =

0.17249E+03

Eigenvalue(

6) =

0.403291E+05

Frequency =

0.20082E+03

Eigenvalue(

7) =

0.344521E+05

Frequency =

0.18561E+03

Eigenvalue(

8) =

0.208052E+05

Frequency =

0.14424E+03

Eigenvalue(

9) =

0.174488E+05

Frequency =

0.13209E+03

Eigenvalue( 10) =

0.115714E+05

Frequency =

0.10757E+03

Eigenvalue( 11) =

0.849973E+04

Frequency =

0.92194E+02

Eigenvalue( 12) =

0.262268E+04

Frequency =

0.51212E+02

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

377

Problem 13.39: Determine the eigenvalues of the circular membrane problem in Fig. P8.49 with a mesh of four quadratic triangular elements. Use c = 1.0. Solution: Input data and partial output are included in Box 13.39. Box 13.39: Input data and edited output for the mesh of four quadratic elements. Prob 13.39: Vibrations of a circular membrane (quadratic triangles) 0 2 2 1 ITYPE,IGRAD,ITEM,NEIGN 10 1 0 6 0 0 IELTYP,NPE,MESH,NPRNT 4 15 NEM, NNM 1 3 10 2 7 6 3 12 10 8 11 7 3 5 12 4 9 8 10 12 15 11 14 13 NOD(I,J) 0.0 0.0 0.25 0.0 0.5 0.0 0.75 0.0 1.0 0.0 0.17677 0.17677 0.46194 0.19134 0.73559 0.14632 0.98078 0.19509 0.35355 0.35355 0.62360 0.41668 0.92388 0.38268 0.53033 0.53033 0.83147 0.55557 0.70711 0.70711 GLXY(I,J) 5 NSPV 5 1 9 1 12 1 14 1 15 1 ISPV(I,J) 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 1.0 0.0 0.0 C0, CX, CY Eigenvalue( 1) Eigenvalue( 2) Eigenvalue( 3) Eigenvalue( 4) Eigenvalue( 9) Eigenvalue( 10)

= = = = = =

0.587824E+03 0.554397E+03 0.489670E+03 0.280291E+03 0.313889E+02 0.579571E+01

Frequency Frequency Frequency Frequency Frequency Frequency

= = = = = =

0.24245E+02 0.23546E+02 0.22128E+02 0.16742E+02 0.56026E+01 0.24074E+01

3.00 2.00

Mode shape 1

Deflection, w

1.00 0.00 -1.00 -2.00

Mode shape 2

-3.00 -4.00 -5.00 0.00

0.20

0.40

0.60

0.80

1.00

Radial distance, x

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

378

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.40: Determine the transient response of the problem in Fig. P8.49 (see Problem 13.39). Assume zero initial conditions, c = 1 and f0 = 1. Use α = γ = 0.5, ∆t = 0.05, and plot the center deflection versus time t for t = 0 to t = 2.4. Solution: Input data and partial output are included in Boxes 13.40a and 13.40b. Box 13.40a: Input data for the transient response of a circular membrane (mesh of four quadratic elements is used). Prob 13.40: Transient analysis of a circular membrane (quadr tri) 0 2 2 0 ITYPE,IGRAD,ITEM,NEIGN 0 6 0 0 IELTYP,NPE,MESH,NPRNT 4 15 NEM, NNM 1 3 10 2 7 6 3 12 10 8 11 7 3 5 12 4 9 8 10 12 15 11 14 13 NOD(I,J) 0.0 0.0 0.25 0.0 0.5 0.0 0.75 0.0 1.0 0.0 0.17677 0.17677 0.46194 0.19134 0.73559 0.14632 0.98078 0.19509 0.35355 0.35355 0.62360 0.41668 0.92388 0.38268 0.53033 0.53033 0.83147 0.55557 0.70711 0.70711 GLXY(I,J) 5 NSPV 5 1 9 1 12 1 14 1 15 1 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 VSPV(I) 0 NSSV 1.0 0.0 0.0 A10, A1X, A1Y 1.0 0.0 0.0 A20, A2X, A2Y 0.0 A00 0 ICONV 1.0 0.0 0.0 F0, FX, FY 1.0 0.0 0.0 C0, CX, CY 50 51 1 0 NTIME,NSTP,INTVL,INTIAL 0.05 0.5 0.5 1.0E-5 DT,ALFA,GAMA,EPSLN y

•15•14 • 12 6 • • •9 •• •• •1 •2 •3 •4 •5 13 10

1

a

1

x

Mesh of 4 quadratic triangles

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

379

Box 13.40b: Edited output for the transient response of a circular membrane (mesh of four quadratic elements is used). *TIME* = 0.50000E-01 Node 1 2 3 4 5

x-coord. 0.00000E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.10000E+01

Time Step Number =

1

y-coord.

Primary DOF

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00

0.50716E-03 0.63430E-03 0.41805E-03 0.82401E-03 0.00000E+00

*TIME* = 0.50000E+00 1 0.00000E+00 2 0.25000E+00 3 0.50000E+00 4 0.75000E+00 5 0.10000E+01

Time Step Number = 10 0.00000E+00 0.10904E+00 0.00000E+00 0.11163E+00 0.00000E+00 0.11476E+00 0.00000E+00 0.83341E-01 0.00000E+00 0.00000E+00

*TIME* = 0.10000E+01 1 0.00000E+00 2 0.25000E+00 3 0.50000E+00 4 0.75000E+00 5 0.10000E+01

Time Step Number = 20 0.00000E+00 0.48343E+00 0.00000E+00 0.42507E+00 0.00000E+00 0.30774E+00 0.00000E+00 0.16717E+00 0.00000E+00 0.00000E+00

*TIME* = 0.20000E+01 1 0.00000E+00 2 0.25000E+00 3 0.50000E+00 4 0.75000E+00 5 0.10000E+01

Time Step Number = 40 0.00000E+00 0.22552E+00 0.00000E+00 0.22546E+00 0.00000E+00 0.18105E+00 0.00000E+00 0.10533E+00 0.00000E+00 0.00000E+00

1.00

∆t = 0.05, α = 0.5, γ = 0.5

Deflection, w(0,0,t)

0.80 0.60 0.40 0.20 0.00 -0.20 -0.40 0.00

0.50

1.00

1.50

2.00

2.50

Time, t

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

380

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.41: Analyze the viscous flow problem in Problem 10.8 using an 8 × 8 mesh of linear rectangular elements. Plot the horizontal velocity u(0.5, y) versus y, and the pressure along the top surface of the cavity. Investigate the effect of the penalty parameter on the solution (see Fig. P10.8). Solution: Input data and partial output are included in Boxe 13.41. Also, see Fig. 13.41 for plots of the velocity vx (0.5, y) versus y and P (x, 0.9375) versus x. Box 13.41: Input data and partial output for the lid-driven cavity problem (uniform mesh of 8 × 8 rectangular elements is used). Prob. 13.41: Steady flow of viscous incompressible fluid in a cavity 1 1 0 0 0 ITYPE,ISTRS,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 8 8 NX, NY 0.0 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.125 X0, DX(I) 0.0 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.125 Y0, DY(I) 64 NSPV 1 1 1 2 2 1 2 2 3 1 3 2 4 1 4 2 5 1 5 2 6 1 6 2 7 1 7 2 8 1 8 2 9 1 9 2 10 1 10 2 18 1 18 2 19 1 19 2 27 1 27 2 28 1 28 1 36 1 36 2 37 1 37 2 45 1 45 2 46 1 46 2 54 1 54 2 55 1 55 2 63 1 63 2 64 1 64 2 72 1 72 2 73 1 73 2 74 1 74 2 75 1 75 2 76 1 76 2 77 1 77 2 78 1 78 2 79 1 79 2 80 1 80 2 81 1 81 2 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.38268 0.0 0.7071 0.0 0.92388 0.0 1.0 0.0 0.92388 0.0 0.7071 0.0 0.38268 0.0 0.0 0.0 0 NSSV 1.0 1.0E2 AMU, PENLTY 0.0 0.0 0.0 F0, FX, FY Node

x-coord.

y-coord.

Value of u

Value of v

5 14 23 32 41 50 59 68 77

0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00

0.00000E+00 0.12500E+00 0.25000E+00 0.37500E+00 0.50000E+00 0.62500E+00 0.75000E+00 0.87500E+00 0.10000E+01

0.00000E+00 -0.56878E-01 -0.10743E+00 -0.13835E+00 -0.18925E+00 -0.16489E+00 -0.61431E-01 0.29025E+00 0.10000E+01

0.00000E+00 0.29798E-02 -0.58367E-02 0.69427E-03 -0.57231E-02 0.95842E-03 -0.27417E-02 0.14788E-02 0.00000E+00

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

381

(a)

Velocity vx(0.5, y)

1.00

0.80 0 γ = 10

0.60

2

2 γ = 108

0.40

0.20

0.00 -0.4 -0.2

0.0

0.2

0.4

0.6

0.8

1.0

Distance, y

25.00

(b)

Pressure, P (x,0.9375)

20.00

0 γ = 10

15.00

2

2 γ = 108

10.00 5.00 0.00 -5.00 -10.00 -15.00 -20.00 -25.00 0.0

0.2

0.4

0.6

0.8

1.0

Distance, x

Figure 13.41: Plots of (a) velocity vx (0.5, y) versus y and (b) P (x, 0.9375) versus x for the lid-driven cavity (uniform mesh of 8 × 8 rectangular elements is used).

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

382

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.46: Analyze the cavity problem in Problem 13.41 for its transient solution. Use ρ = 1.0, zero initial conditions, penalty parameter γ = 108 , time parameter α = 0.5, and a time step of ∆t = 0.005 to capture the evolution of vx (0.5, y) with time. Solution: Input data and partial output are included in Box 13.46. Box 13.46: Input data and partial output for the transient analysis of the liddriven cavity problem (uniform mesh of 8 × 8 rectangular elements). Prob. 13.46: Transient analysis of 1 1 1 0 1 4 1 0 8 8 0.0 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.0 0.125 0.125 0.125 0.125 0.125 0.125 0.125 0.125 64 1 1 1 2 2 1 2 2 3 1 6 1 6 2 7 1 7 2 8 1 18 1 18 2 19 1 19 2 27 1 37 1 37 2 45 1 45 2 46 1 63 1 63 2 64 1 64 2 72 1 75 1 75 2 76 1 76 2 77 1 80 1 80 2 81 1 81 2 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.7071 0.0 0.92388 0.0 1.0 0.38268 0.0 0.0 0.0 0 1.0 1.0E8 0.0 0.0 0.0 1.0 0.0 0.0 20 21 1 0 0.005 0.5 0.5 1.0E-3

the lid-driven cavity problem ITYPE,ISTRS,ITEM,NEIGN IEL, NPE, MESH, NPRNT NX, NY X0, DX(I)

3 8 27 46 72 77

2 2 2 2 2 2

0.0 0.0 0.0 0.0 0.0 0.0

Y0, DY(I) NSPV 4 1 4 2 9 1 9 2 28 1 28 1 54 1 54 2 73 1 73 2 78 1 78 2

5 10 36 55 74 79

0.0 0.0 0.0 0.0 0.0 0.92388

0.0 0.0 0.0 0.0 0.38268 0.7071

0.0 0.0 0.0 0.0 0.0 0.0

1 1 1 1 1 1

Velocity

0.80

8 t

t = 0.02 t = 0.03

4 t = 0.05

0.40

•

Steady − state (t = 0.085)

0.20

0.00 -0.4 -0.2

0.0

0.2

0.4

0.6

0.8

1.0

Distance, y PROPRIETARY MATERIAL.

2 2 2 2 2 2

0.0 0.0 0.0 0.0 0.0 0.0

NSSV AMU, PENLTY F0, FX, FY C0, CX, CY NTIME,NSTP,INTVL,INTIAL DT,ALFA,GAMA,EPSLN

1.00

0.60

5 10 36 55 74 79

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

383

Problem 13.48: Analyze the plane elasticity problem in Fig. P11.7 using 10 × 4 mesh of linear rectangular elements. Evaluate the results (i.e., displacements and stresses) qualitatively. Use the plane stress assumption. Solution: The loads at nodes 11, 22, 44 and 55 were calculated in the solution to Problem 11.7. The input data and partial output are included in Boxes 13.48a through 13.48c. Note that the vertical deflection as per the classical beam theory is (for a beam fixed at the left end and subjected to pure bending moment at the right end) M0 x2 hb3 2 uy (x) = − where I = = 2EI 12 3 Hence, the vertical deflection at node 11 or 55 as per the beam theory is uy (6) = −0.54 × 10−3 cm. The elasticity solution predicted with the chosen mesh is uy (6, 0) = −0.5144 × 10−3 cm. Of course, the boundary conditions of elasticity are not quite the same as the “fixed” boundary condition used in arriving at the beam deflection. Box 13.48a: Input data for the static analysis of the plane stress problem in Fig. P11.7 (nonuniform mesh of 10 × 4 rectangular elements is used). Problem 13.48: Bending of a cantilever plate using elasticity eqs 2 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IELTYP,NPE,MESH,NPRNT 10 4 NX, NY 0.0 0.125 0.125 0.25 0.25 0.5 0.75 0.75 1.0 1.0 1.25 X0,DX(I) 0.0 0.5 0.5 0.5 0.5 Y0,DY(I) 6 NSPV 1 1 12 1 23 1 23 2 34 1 45 1 ISPV 0.0 0.0 0.0 0.0 0.0 0.0 VSPV 4 NSSV 11 1 22 1 44 1 55 1 ISSV -187.5 -225.0 225.0 187.5 VSSV 1 LNSTRS 30.0E06 30.0E06 0.3 11.53846E06 1.0 E1,E2,ANU12,G12,THKNS 0.0 0.0 0.0 F0, FX, FY Plane stress 45 M

2 cm

E = 3 × 107 N/cm 2 , ν = 0.3 h = 1 cm, M 0 = 600 N − cm 55

M

44

7

33

M

22

M

11

1

PROPRIETARY MATERIAL.

6 cm

M0

c The McGraw-Hill Companies, Inc. °

h

All rights reserved.

384

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Box 13.48b: Deflections of the plane stress problem in Fig. P11.7 (nonuniform mesh of 10 × 4 rectangular elements is used). Node

x-coord.

y-coord.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

0.00000E+00 0.12500E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.12500E+01 0.20000E+01 0.27500E+01 0.37500E+01 0.47500E+01 0.60000E+01 0.00000E+00 0.12500E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.12500E+01 0.20000E+01 0.27500E+01 0.37500E+01 0.47500E+01 0.60000E+01 0.12500E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.12500E+01 0.20000E+01 0.27500E+01 0.37500E+01 0.47500E+01 0.60000E+01 0.00000E+00 0.12500E+00 0.25000E+00 0.50000E+00 0.75000E+00 0.12500E+01 0.20000E+01 0.27500E+01 0.37500E+01 0.47500E+01 0.60000E+01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.50000E+00 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.15000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01 0.20000E+01

PROPRIETARY MATERIAL.

Value of u 0.00000E+00 -0.37352E-05 -0.74728E-05 -0.14897E-04 -0.22359E-04 -0.36942E-04 -0.58041E-04 -0.79386E-04 -0.10646E-03 -0.13396E-03 -0.16520E-03 0.00000E+00 -0.18461E-05 -0.36899E-05 -0.73777E-05 -0.11029E-04 -0.18282E-04 -0.29024E-04 -0.39502E-04 -0.53253E-04 -0.66617E-04 -0.84050E-04 0.18461E-05 0.36899E-05 0.73777E-05 0.11029E-04 0.18282E-04 0.29024E-04 0.39502E-04 0.53253E-04 0.66617E-04 0.84050E-04 0.00000E+00 0.37352E-05 0.74728E-05 0.14897E-04 0.22359E-04 0.36942E-04 0.58041E-04 0.79386E-04 0.10646E-03 0.13396E-03 0.16520E-03

c The McGraw-Hill Companies, Inc. °

Value of v -0.44216E-05 -0.46542E-05 -0.53515E-05 -0.81369E-05 -0.12776E-04 -0.27563E-04 -0.63135E-04 -0.11462E-03 -0.20746E-03 -0.32777E-03 -0.51440E-03 -0.10905E-05 -0.13241E-05 -0.20262E-05 -0.48223E-05 -0.94826E-05 -0.24330E-04 -0.59949E-04 -0.11150E-03 -0.20443E-03 -0.32466E-03 -0.51167E-03 -0.13241E-05 -0.20262E-05 -0.48223E-05 -0.94826E-05 -0.24330E-04 -0.59949E-04 -0.11150E-03 -0.20443E-03 -0.32466E-03 -0.51167E-03 -0.44216E-05 -0.46542E-05 -0.53515E-05 -0.81369E-05 -0.12776E-04 -0.27563E-04 -0.63135E-04 -0.11462E-03 -0.20746E-03 -0.32777E-03 -0.51440E-03

All rights reserved.

SOLUTIONS MANUAL

385

Box 13.48c: Stresses in the plane stress problem in Fig. P11.7 (nonuniform mesh of 10 × 4 rectangular elements is used). x-coord.

y-coord.

0.6250E-01 0.1875E+00 0.3750E+00 0.6250E+00 0.1000E+01 0.1625E+01 0.2375E+01 0.3250E+01 0.4250E+01 0.5375E+01 0.6250E-01 0.1875E+00 0.3750E+00 0.6250E+00 0.1000E+01 0.1625E+01 0.2375E+01 0.3250E+01 0.4250E+01 0.5375E+01 0.6250E-01 0.1875E+00 0.3750E+00 0.6250E+00 0.1000E+01 0.1625E+01 0.2375E+01 0.3250E+01 0.4250E+01 0.5375E+01 0.6250E-01 0.1875E+00 0.3750E+00 0.6250E+00 0.1000E+01 0.1625E+01 0.2375E+01 0.3250E+01 0.4250E+01 0.5375E+01

0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.2500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.7500E+00 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1250E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01 0.1750E+01

sigma-x -0.6701E+03 -0.6702E+03 -0.6670E+03 -0.6674E+03 -0.6553E+03 -0.6363E+03 -0.6370E+03 -0.6121E+03 -0.6127E+03 -0.5842E+03 -0.2219E+03 -0.2216E+03 -0.2217E+03 -0.2194E+03 -0.2176E+03 -0.2148E+03 -0.2094E+03 -0.2066E+03 -0.1993E+03 -0.2097E+03 0.2219E+03 0.2216E+03 0.2217E+03 0.2194E+03 0.2176E+03 0.2148E+03 0.2094E+03 0.2066E+03 0.1993E+03 0.2097E+03 0.6701E+03 0.6702E+03 0.6670E+03 0.6674E+03 0.6553E+03 0.6363E+03 0.6370E+03 0.6121E+03 0.6127E+03 0.5842E+03

sigma-y -0.1195E+01 -0.1392E+01 -0.8944E+00 -0.1988E+01 -0.8439E+00 0.1668E+01 -0.1882E+01 0.1002E+01 0.5985E+00 0.2066E-01 -0.1148E+01 -0.1015E+01 -0.1320E+01 -0.1218E+01 -0.6825E-01 0.2441E+00 0.3678E+00 -0.1173E+01 0.3700E+01 -0.1637E+01 0.1148E+01 0.1015E+01 0.1320E+01 0.1218E+01 0.6825E-01 -0.2441E+00 -0.3678E+00 0.1173E+01 -0.3700E+01 0.1637E+01 0.1195E+01 0.1392E+01 0.8944E+00 0.1988E+01 0.8439E+00 -0.1668E+01 0.1882E+01 -0.1002E+01 -0.5985E+00 -0.2066E-01

sigma-xy 0.2801E+00 0.8576E+00 0.1599E+01 0.2901E+01 0.4113E+01 0.2497E+01 0.2429E+01 0.2420E+01 0.3200E+01 -0.1109E+02 -0.2801E+00 -0.8576E+00 -0.1599E+01 -0.2901E+01 -0.4113E+01 -0.2497E+01 -0.2429E+01 -0.2420E+01 -0.3200E+01 0.1109E+02 -0.2801E+00 -0.8576E+00 -0.1599E+01 -0.2901E+01 -0.4113E+01 -0.2497E+01 -0.2429E+01 -0.2420E+01 -0.3200E+01 0.1109E+02 0.2801E+00 0.8576E+00 0.1599E+01 0.2901E+01 0.4113E+01 0.2497E+01 0.2429E+01 0.2420E+01 0.3200E+01 -0.1109E+02

y

2 cm

1

PROPRIETARY MATERIAL.

M

55

M

44

7

33

M

22

M

11

6 cm

c The McGraw-Hill Companies, Inc. °

x

All rights reserved.

386

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.60: Analyze the plane elasticity problem in Fig. P11.7 for natural frequencies. Use a density of ρ = 0.0088 kg/cm3 . Solution: The input data and partial output are included in Box 13.60. Box 13.60: Input data and partial output for the vibration analysis of the plane stress problem in Fig. P11.7 (nonuniform mesh of 10 × 4 rectangular elements is used). Problem 13.60: Vibration of a cantilever plate using plane stress element 2 1 2 1 ITYPE,IGRAD,ITEM,NEIGN 10 0 NVALU, NVCTR 1 4 1 0 IELTYP,NPE,MESH,NPRNT 10 4 NX, NY 0.0 0.125 0.125 0.25 0.25 0.5 0.75 0.75 1.0 1.0 1.25 X0,DX(I) 0.0 0.5 0.5 0.5 0.5 Y0,DY(I) 6 NSPV 1 1 12 1 23 1 23 2 34 1 45 1 ISPV 1 LNSTRS 30.0E06 30.0E06 0.3 11.53846E06 1.0 E1,E2,ANU12,G12,THKNS 0.0088 0.0 0.0 C0, CX, CY

OUTPUT

from

program *** FEM2D *** by J. N. REDDY

MATERIAL PROPERTIES OF THE SOLID ANALYZED: Thickness of the body, THKNS ............= Modulus of elasticity, E1 ...............= Modulus of elasticity, E2 ...............= Poisson s ratio, ANU12 ..................= Shear modulus, G12 ......................=

0.1000E+01 0.3000E+08 0.3000E+08 0.3000E+00 0.1154E+08

PARAMETERS OF THE DYNAMIC ANALYSIS: Coefficient, C0 .........................= Coefficient, CX .........................= Coefficient, CY .........................=

0.8800E-02 0.0000E+00 0.0000E+00

(Only ten frequencies were requested - these are the highest ten) Eigenvalue( 1) Eigenvalue( 2) Eigenvalue( 3) Eigenvalue( 4) Eigenvalue( 5) Eigenvalue( 6) Eigenvalue( 7) Eigenvalue( 8) Eigenvalue( 9) Eigenvalue( 10)

= = = = = = = = = =

0.126100E+13 0.123934E+13 0.121864E+13 0.120075E+13 0.119229E+13 0.887367E+12 0.875914E+12 0.774362E+12 0.773088E+12 0.531354E+12

PROPRIETARY MATERIAL.

Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency Frequency

= = = = = = = = = =

c The McGraw-Hill Companies, Inc. °

0.11229E+07 0.11133E+07 0.11039E+07 0.10958E+07 0.10919E+07 0.94200E+06 0.93590E+06 0.87998E+06 0.87925E+06 0.72894E+06

All rights reserved.

SOLUTIONS MANUAL

387

Problem 13.67: Analyze the plate problem in Fig. P12.2 using (a) 2×4 and (b) 4×8 meshes of CPT(N) elements in the half-plate, and compare the maximum deflections and stresses. Use E = 107 psi, ν = 0.25, h = 0.25 in. and q0 = 10 lb/in. Solution: Note that a plate strip of unit width along the x-axis may be modeled. The input data and partial output are included in Boxes 13.67a and 13.67b. Box 13.67a: Input data and partial output for the plate problem in Fig. P12.2 (uniform mesh of 2 × 4 elements is used). Problem 13.67a: Bending of a cantilever plate--CPT(N) 4 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 2 4 NX, NY 0.0 2.5 2.5 X0, DX(I) 0.0 2.5 2.5 2.5 2.5 Y0, DY(I) 9 NSPV 1 1 1 2 1 3 2 1 2 2 2 3 3 1 3 2 3 3 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 3 NSSV 13 1 14 1 15 1 ISSV(I,J) 12.5 25.0 12.5 VSSV(I) 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.0 0.0 F0, FX, FY Node 4 5 6 7 8 9 10 11 12 13 14 15

x-coord.

y-coord.

deflec. w

x-rotation

y-rotation

0.00000E+00 0.25000E+01 0.19679E-01 0.31193E-02 0.19671E-01 0.25000E+01 0.25000E+01 0.22091E-01 0.75123E-16 0.20484E-01 0.50000E+01 0.25000E+01 0.19679E-01 -0.31193E-02 0.19671E-01 0.00000E+00 0.50000E+01 0.75492E-01 0.26409E-02 0.34988E-01 0.25000E+01 0.50000E+01 0.78068E-01 0.16786E-15 0.34732E-01 0.50000E+01 0.50000E+01 0.75492E-01 -0.26409E-02 0.34988E-01 0.00000E+00 0.75000E+01 0.15559E+00 0.16643E-02 0.44033E-01 0.25000E+01 0.75000E+01 0.15731E+00 0.27205E-15 0.43639E-01 0.50000E+01 0.75000E+01 0.15559E+00 -0.16643E-02 0.44033E-01 0.00000E+00 0.10000E+02 0.24768E+00 0.91430E-03 0.47094E-01 0.25000E+01 0.10000E+02 0.24878E+00 0.20634E-15 0.46846E-01 0.50000E+01 0.10000E+02 0.24768E+00 -0.91430E-03 0.47094E-01 _________________________________________________________________ x-coord. y-coord. sigma-x sigma-y sigma-xy _________________________________________________________________ 0.5283E+00 0.5283E+00 0.1972E+01 0.1972E+01

0.5283E+00 0.1972E+01 0.5283E+00 0.1972E+01

PROPRIETARY MATERIAL.

-0.1789E+04 -0.5910E+03 -0.2230E+04 -0.1294E+04

-0.8624E+04 -0.7845E+04 -0.9562E+04 -0.7569E+04

c The McGraw-Hill Companies, Inc. °

-0.1198E+04 -0.1498E+04 -0.4551E+02 -0.3459E+03

All rights reserved.

388

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Box 13.67b: Input data and partial output for the plate problem in Fig. P12.2 (uniform mesh of 4 × 8 CPT(N) elements is used). Problem 13.67b: Bending of a cantilever plate--CPT(N) 4 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 4 8 NX, NY 0.0 1.25 1.25 1.25 1.25 X0, DX(I) 0.0 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 Y0, DY(I) 15 NSPV 1 1 1 2 1 3 2 1 2 2 2 3 3 1 3 2 3 3 4 1 4 2 4 3 5 1 5 2 5 3 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 5 NSSV 41 1 42 1 43 1 44 1 45 1 ISSV(I,J) 6.25 12.5 12.5 12.5 6.25 VSSV(I) 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.0 0.0 F0, FX, FY Node 6 7 8 9 10 15 20 25 30 35 40 41 42 43 44 45

x-coord. 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01

y-coord.

deflec. w

x-rotation

y-rotation

0.12500E+01 0.12500E+01 0.12500E+01 0.12500E+01 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01 0.62500E+01 0.75000E+01 0.87500E+01 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02

0.45692E-02 0.56632E-02 0.58457E-02 0.56632E-02 0.45692E-02 0.19435E-01 0.43563E-01 0.75357E-01 0.11323E+00 0.15563E+00 0.20100E+00 0.24783E+00 0.24863E+00 0.24894E+00 0.24863E+00 0.24783E+00

0.10728E-02 0.22657E-03 -0.34104E-15 -0.22657E-03 -0.10728E-02 -0.14134E-02 -0.14550E-02 -0.13065E-02 -0.10749E-02 -0.82104E-03 -0.59641E-03 0.46503E-03 0.30049E-03 -0.65314E-14 -0.30049E-03 -0.46503E-03

0.48607E-02 0.54417E-02 0.56179E-02 0.54417E-02 0.48607E-02 0.98734E-02 0.14111E-01 0.17546E-01 0.20196E-01 0.22069E-01 0.23171E-01 0.23543E-01 0.23485E-01 0.23473E-01 0.23485E-01 0.23543E-01

x-coord.

y-coord.

sigma-x

sigma-y

sigma-xy

0.2642E+00 0.2642E+00 0.9858E+00 0.9858E+00

0.2642E+00 0.9858E+00 0.2642E+00 0.9858E+00

-0.1557E+04 -0.6436E+03 -0.2176E+04 -0.1526E+04

-0.7856E+04 -0.8642E+04 -0.9368E+04 -0.8578E+04

-0.1596E+04 -0.2455E+04 -0.3455E+03 -0.1204E+04

1 2

6

41

10 15

45

y

3 4 5

x PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

389

Problem 13.69: Repeat Problem 13.67 with an 4 × 8 mesh of linear plate elements and a 2 × 4 mesh of nine-node quadratic plate elements based on the first-order plate theory. Solution: The input data and partial output are included in Boxes 13.69a and 13.69b. Box 13.69a: Input data and partial output for the plate problem in Fig. P12.2 (uniform mesh of 4 × 8 of Q4 elements is used). Problem 13.69a: Bending of a cantilever plate--SDT 3 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 4 8 NX, NY 0.0 1.25 1.25 1.25 1.25 X0, DX(I) 0.0 1.25 1.25 1.25 1.25 1.25 1.25 1.25 1.25 Y0, DY(I) 15 NSPV 1 1 1 2 1 3 2 1 2 2 2 3 3 1 3 2 3 3 4 1 4 2 4 3 5 1 5 2 5 3 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 5 NSSV 41 1 42 1 43 1 44 1 45 1 ISSV(I,J) 6.25 12.5 12.5 12.5 6.25 VSSV(I) 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.0 0.0 F0, FX, FY Node 10 15 20 25 30 41 42 43 44 45

x-coord. 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01

y-coord.

deflec. w

x-rotation

y-rotation

0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01 0.62500E+01 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02

0.44671E-02 0.19099E-01 0.43181E-01 0.74983E-01 0.11286E+00 0.24742E+00 0.24815E+00 0.24845E+00 0.24815E+00 0.24742E+00

0.17611E-02 0.23954E-02 0.24843E-02 0.21559E-02 0.17640E-02 -0.68934E-03 -0.47107E-03 -0.18010E-14 0.47107E-03 0.68934E-03

-0.78276E-02 -0.15928E-01 -0.22636E-01 -0.28075E-01 -0.32297E-01 -0.37657E-01 -0.37669E-01 -0.37563E-01 -0.37669E-01 -0.37657E-01

x-coord.

y-coord.

0.6250E+00

0.6250E+00

0.1875E+01

0.6250E+00

0.3125E+01

0.6250E+00

0.4375E+01

0.6250E+00

PROPRIETARY MATERIAL.

sigma-x sigma-xz -0.1319E+04 -0.7114E+02 -0.2301E+04 -0.7114E+02 -0.2301E+04 0.7114E+02 -0.1319E+04 0.7114E+02

sigma-y sigma-yz

sigma-xy

-0.8449E+04 -0.7884E+02 -0.9551E+04 0.1748E+03 -0.9551E+04 0.1748E+03 -0.8449E+04 -0.7884E+02

-0.5037E+03

c The McGraw-Hill Companies, Inc. °

-0.2611E+03 0.2611E+03 0.5037E+03

All rights reserved.

390

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Box 13.69b: Input data and partial output for the plate problem in Fig. P12.2 (uniform mesh of 2 × 4 of Q9 elements is used). Problem 13.69b: Bending of a cantilever plate--FSDT 3 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 2 9 1 0 IEL, NPE, MESH, NPRNT 2 4 NX, NY 0.0 2.5 2.5 X0, DX(I) 0.0 2.5 2.5 2.5 2.5 Y0, DY(I) 15 NSPV 1 1 1 2 1 3 2 1 2 2 2 3 3 1 3 2 3 3 4 1 4 2 4 3 5 1 5 2 5 3 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 5 NSSV 41 1 42 1 43 1 44 1 45 1 ISSV(I,J) 6.25 12.5 12.5 12.5 6.25 VSSV(I) 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.0 0.0 F0, FX, FY Node 10 15 20 25 30 40 41 42 43 44 45

x-coord. 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01

y-coord.

deflec. w

x-rotation

y-rotation

0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01 0.62500E+01 0.87500E+01 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02 0.10000E+02

0.44331E-02 0.19219E-01 0.43537E-01 0.75537E-01 0.11358E+00 0.20176E+00 0.24885E+00 0.24934E+00 0.24972E+00 0.24934E+00 0.24885E+00

0.18711E-02 0.24401E-02 0.24463E-02 0.21228E-02 0.17336E-02 0.85669E-03 -0.32113E-03 -0.41224E-03 -0.30984E-13 0.41224E-03 0.32113E-03

-0.80203E-02 -0.16063E-01 -0.22652E-01 -0.28099E-01 -0.32312E-01 -0.37089E-01 -0.37601E-01 -0.37695E-01 -0.37504E-01 -0.37695E-01 -0.37601E-01

sigma-x sigma-xz

sigma-y sigma-yz

sigma-xy

-0.8471E+04 -0.5962E+02 -0.7983E+04 0.3187E+02 -0.9714E+04 0.1556E+03 -0.7431E+04 0.6413E+02

-0.5521E+03

x-coord.

y-coord.

0.5283E+00

0.5283E+00

0.5283E+00

0.1972E+01

0.1972E+01

0.5283E+00

0.1972E+01

0.1972E+01

1 2

-0.1224E+04 -0.5876E+02 -0.2164E+03 -0.3272E+02 -0.2372E+04 -0.8276E+02 -0.1279E+04 -0.8725E+01

6

41

10 15

45

-0.3795E+03 -0.2572E+03 -0.4473E+03

y

3 4 5

x

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

391

Problem 13.70: Analyze the plate bending problem in Fig. P12.3 with the CPT (C) elements. Use the mesh shown in the figure, and take E = 107 psi, ν = 0.25, h = 0.25 in. and q0 = 10 lb/in2 . y 7

∂w =0 ∂x

4

5"

•

•

5

• •

• •

2

1

• 6

9

•

5"

∂w =w=0 ∂y

x

•3

∂w =0 ∂y

∂ 2w =0 ∂x∂y

Solution: The input data and partial output are included in Box 13.70 for 2 × 2 mesh of CPT(C) elements. We take a = b = 10 in. Box 13.70: Input data and partial output for the plate problem of Fig. P12.3. Problem 13.70: Bending of a square 5 1 0 0 1 4 1 0 2 2 0.0 2.5 2.5 0.0 2.5 2.5 12 1 2 1 3 1 4 2 3 3 1 4 2 6 1 6 3 7 2 9 1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 10.0 0.0 0.0 Node 1 2 3 4 5 6 7 8 9

x-coord. 0.00000E+00 0.25000E+01 0.50000E+01 0.00000E+00 0.25000E+01 0.50000E+01 0.00000E+00 0.25000E+01 0.50000E+01 x-coord. 0.5283E+00

plate (Prob 12.3)--CPT(C) ITYPE,IGRAD,ITEM,NEIGN IEL, NPE, MESH, NPRNT NX, NY X0, DX(I) Y0, DY(I) NSPV 3 3 9 3 ISPV(I,J) 0.0 0.0 NSSV 0.25 E1,E2,ANU12,G12,…,THKNS F0, FX, FY

y-coord.

deflec. w

x-rotation

y-rotation

0.00000E+00 0.00000E+00 0.00000E+00 0.25000E+01 0.25000E+01 0.25000E+01 0.50000E+01 0.50000E+01 0.50000E+01

0.10189E+00 0.71852E-01 0.00000E+00 0.10507E+00 0.73270E-01 0.00000E+00 0.11635E+00 0.79587E-01 0.00000E+00

0.00000E+00 -0.28389E-01 -0.40707E-01 0.00000E+00 -0.28671E-01 -0.40833E-01 0.00000E+00 -0.30646E-01 -0.44033E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.24985E-02 0.14430E-02 0.00000E+00 0.73965E-04 0.43428E-02 0.00000E+00

y-coord. 0.5283E+00

PROPRIETARY MATERIAL.

sigma-x 0.1284E+05

sigma-y 0.2055E+04

c The McGraw-Hill Companies, Inc. °

sigma-xy 0.8893E+03

All rights reserved.

392

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.71: Analyze the plate bending problem in Fig. P12.4 with the CPT (C) elements. Use the mesh shown in the figure, and take E = 107 psi, ν = 0.25, h = 0.25 in. and q0 = 10 lb/in2 .

y

w=

11 w=

∂w ∂w ∂ 2w = = =0 ∂x ∂y ∂x∂y

• •6 •1

∂w =0 ∂x

•

•

•

•

•

•

•

3

•

4

2

•

∂w =0 ∂y

⎛x⎞ q( x , y ) = q0 ⎜ ⎟ ⎝a⎠

•15 10

• b = 5" x

5• b = 5"

a = 10"

Solution: The input data and partial output are included in Box 13.71 for 4 × 2 mesh of CPT(C) elements. We take a = 10 in. and b = 5 in. Box 13.71: Input data and partial output for the plate problem of Fig. P12.4. Problem 13.71: Bending of a rectangular plate--CPT(C) 5 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 4 2 NX, NY 0.0 2.5 2.5 2.5 2.5 X0, DX(I) 0.0 2.5 2.5 Y0, DY(I) 24 NSPV 1 1 1 2 1 3 1 4 2 3 3 3 4 3 5 3 6 1 6 2 6 3 6 4 11 1 11 2 11 3 11 4 12 1 12 2 13 1 13 2 14 1 14 2 15 1 15 2 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 0 NSSV 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.5 0.0 F0, FX, FY Node 1 2 3 4 5

x-coord. 0.00000E+00 0.25000E+01 0.50000E+01 0.75000E+01 0.10000E+02 x-coord. 0.5283E+00 0.9472E+01 0.4472E+01

y-coord. 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 y-coord. 0.5283E+00 0.1972E+01 0.4472E+01

PROPRIETARY MATERIAL.

deflec. w 0.00000E+00 0.48452E-02 0.13736E-01 0.22636E-01 0.31321E-01

sigma-x -0.2276E+04 0.5033E+03 0.8189E+02

x-rotation 0.00000E+00 0.43387E-02 0.49391E-02 0.43107E-02 0.27373E-02

sigma-y -0.4638E+03 0.2797E+04 0.3101E+03

c The McGraw-Hill Companies, Inc. °

y-rotation 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00

sigma-xy -0.8866E+02 0.1672E+04 0.2266E+04

All rights reserved.

SOLUTIONS MANUAL

393

Problem 13.72: Analyze the plate bending problem in Fig. P12.8 with the CPT (C) elements. Use the data shown in the figure.

w=

∂w ∂w ∂ 2w =0 = = ∂y ∂x∂y ∂x

E1 = 30 × 106 psi, E2 = 0.75 × 106 psi,

7

ν 12 = 0.25, G12 = 0.375 × 10 psi 6

h = 2 in, q0 = 100 lb/in

w=

∂w =0 ∂x

∂w =0 ∂x

•

8• 5

• • 2

4•

•

1

9• 6

∂w =0 ∂y

• • 3

b = 15 in

a = 20 in

Solution: The input data and partial output are included in Box 13.72 for 2 × 2 mesh of CPT(C) elements. Box 13.72: Input data and partial output for the plate problem of Fig. P12.8. Problem 13.72: Bending of a rectangular plate (Prob 12.8)--CPT(C) 5 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 2 2 NX, NY 0.0 5.0 5.0 X0, DX(I) 0.0 3.75 3.75 Y0, DY(I) 21 NSPV 1 2 1 3 1 4 2 3 3 1 3 2 3 3 3 4 4 2 6 1 6 2 6 3 6 4 7 1 7 2 8 1 8 2 9 1 9 2 9 3 9 4 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 0 NSSV 30.0E6 0.75E6 0.25 0.375E6 0.375E6 0.375E6 2.0 E1,E2,ANU12,G12,G13,G23,THKNS 100.0 0.0 0.0 F0, FX, FY Node 1 2 3 4 5

x-coord. 0.00000E+00 0.50000E+01 0.10000E+02 0.00000E+00 0.50000E+01 x-coord. 0.8943E+01 0.1057E+01 0.6057E+01

y-coord. 0.00000E+00 0.00000E+00 0.00000E+00 0.37500E+01 0.37500E+01 y-coord. 0.7925E+00 0.6708E+01 0.6708E+01

PROPRIETARY MATERIAL.

deflec. w 0.24556E-02 0.13258E-02 0.00000E+00 0.22172E-02 0.12060E-02

sigma-x -0.3918E+04 -0.1055E+04 -0.2332E+01

x-rotation 0.00000E+00 -0.93499E-03 0.00000E+00 0.00000E+00 -0.82624E-03

sigma-y -0.2247E+02 0.1729E+03 0.3950E+02

c The McGraw-Hill Companies, Inc. °

y-rotation 0.00000E+00 0.00000E+00 0.00000E+00 -0.79161E-03 -0.18107E-03

sigma-xy 0.2886E+01 -0.1011E+03 -0.1784E+03

All rights reserved.

394

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.73: Analyze the plate bending problem in Fig. P12.3 with the SDT elements. Use the mesh shown in the figure, and take E = 107 psi, ν = 0.25, h = 0.25 in. and q0 = 10 lb/in2 . y 5"

φx = 0

• • 11 • • •1

• • • • •2

5"

• • • • •3

• • • • •

25

• • • 5" • • 5"

φy = w = 0

x φy = 0

Solution: The input data and partial output are included in Box 13.73 for 2 × 2 mesh of quadratic SDT elements. We take a = b = 10 in. Box 13.73: Input data and partial output for the plate problem of Fig. P12.3. Node 1 2 3 4 5 6 10 11 15 16 20 21 22 23 24 25

x-coord. 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01 0.00000E+00 0.50000E+01 0.00000E+00 0.50000E+01 0.00000E+00 0.50000E+01 0.00000E+00 0.12500E+01 0.25000E+01 0.37500E+01 0.50000E+01

y-coord.

deflec. w

x-rotation

y-rotation

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.12500E+01 0.12500E+01 0.25000E+01 0.25000E+01 0.37500E+01 0.37500E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01 0.50000E+01

0.93767E-01 0.86732E-01 0.66813E-01 0.36340E-01 0.00000E+00 0.94247E-01 0.00000E+00 0.95918E-01 0.00000E+00 0.99196E-01 0.00000E+00 0.10514E+00 0.97256E-01 0.74931E-01 0.40758E-01 0.00000E+00

0.00000E+00 0.10873E-01 0.20349E-01 0.27044E-01 0.29577E-01 0.00000E+00 0.30301E-01 0.00000E+00 0.30226E-01 0.00000E+00 0.31893E-01 0.00000E+00 0.12163E-01 0.22775E-01 0.30276E-01 0.33118E-01

0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 0.00000E+00 -0.81810E-03 0.00000E+00 -0.18977E-02 0.00000E+00 -0.35244E-02 0.00000E+00 -0.61704E-02 -0.56916E-02 -0.44741E-02 -0.24484E-02 0.00000E+00

x-coord.

y-coord.

0.5283E+00

0.5283E+00

0.4472E+01

0.4472E+01

PROPRIETARY MATERIAL.

sigma-x sigma-xz 0.1165E+05 -0.2085E+02 0.2475E+04 -0.3055E+03

sigma-y sigma-yz 0.2126E+04 -0.6056E+01 0.1225E+03 -0.1762E+01

c The McGraw-Hill Companies, Inc. °

sigma-xy 0.5444E+02 0.1252E+04

All rights reserved.

SOLUTIONS MANUAL

395

Problem 13.76: Analyze the annular plate in Fig. P12.5 using a four element mesh of CPT(C) elements. Use E = 107 psi, ν = 0.25, a = 10 in., b = 5 in., h = 0.25 in. and Q0 = 1 lb/in. Solution: The input data and partial output are included in Box 13.76. There seems to be a problem with the CPT element as applied to circular plates. It does not even preserve the symmetry expected (e.g., w1 = w7 , w2 = w8 , etc.) and the maximum deflection is only 60% of that predicted by the SDT element (see the solution to Problem 13.77). Box 13.76: Input data and partial output for the annular plate problem of Fig. P12.5. Prob 13.76: Bending of a an annular plate under an edge load -- CPT(C) 5 1 0 0 1 4 0 0 4 9 Q0 Q0 1 2 5 4 2 3 6 5 4 5 8 7 y 5 6 9 8 9 • 5.0 0.0 7.5 0.0 10.0 0.0 6 8 3.5355 3.5355 5.3033 5.3033 7.07107 7.07107 • 5 • a 0.0 5.0 0.0 7.5 0.0 10.0 7 4 • •• 9 x 1 3 2 3 3 1 3 3 6 1 7 2 8 2 9 1 9 2 b •1 •2 •3 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 3 1 1 4 1 7 1 1.9635 3.927 1.9635 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 0.0 0.0 0.0

Node 1 2 3 4 5 6 7 8 9

x-coord. 0.50000E+01 0.75000E+01 0.10000E+02 0.35355E+01 0.53033E+01 0.70711E+01 0.00000E+00 0.00000E+00 0.00000E+00

y-coord.

deflec. w

x-rotation

y-rotation

0.00000E+00 0.00000E+00 0.00000E+00 0.35355E+01 0.53033E+01 0.70711E+01 0.50000E+01 0.75000E+01 0.10000E+02

0.61415E-02 0.30838E-02 0.00000E+00 0.50665E-02 0.25292E-02 0.00000E+00 0.22195E-02 0.10317E-02 0.00000E+00

-0.15437E-02 -0.15670E-02 -0.15629E-02 -0.12687E-02 -0.12284E-02 -0.12307E-02 0.00000E+00 0.00000E+00 0.00000E+00

0.00000E+00 0.00000E+00 0.00000E+00 -0.87643E-03 -0.32587E-03 0.86927E-04 -0.10787E-02 -0.61397E-03 0.23336E-03

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

396

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.77: Analyze the annular plate in Fig. P12.5 using a four element mesh of four-node SDT elements. Use E = 107 psi, ν = 0.25, a = 10 in., b = 5 in., h = 0.25 in. and Q0 = 1 lb/in. Solution: The input data and partial output are included in Box 13.77. Box 13.77: Input data and partial output for the annular plate problem of Fig. P12.5. Prob 13.77: Bending of a an annular plate under an edge load (SDT) 3 1 0 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 0 0 IELTYP,NPE,MESH,NPRNT 4 9 NEM, NNM 1 2 5 4 2 3 6 5 4 5 8 7 5 6 9 8 NOD(I,J) 5.0 0.0 7.5 0.0 10.0 0.0 3.5355 3.5355 5.3033 5.3033 7.07107 7.07107 0.0 5.0 0.0 7.5 0.0 10.0 GLXY(I,J) 9 NSPV 1 3 2 3 3 1 3 3 6 1 7 2 8 2 9 1 9 2 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 3 NSSV 1 1 4 1 7 1 ISSV 1.9635 3.927 1.9635 VSSV 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,... 0.0 0.0 0.0 F0, FX, FY

Node 1 2 3 4 5 6 7 8 9

x-coord. 0.50000E+01 0.75000E+01 0.10000E+02 0.35355E+01 0.53033E+01 0.70711E+01 0.00000E+00 0.00000E+00 0.00000E+00

y-coord.

deflec. w

x-rotation

y-rotation

0.00000E+00 0.00000E+00 0.00000E+00 0.35355E+01 0.53033E+01 0.70711E+01 0.50000E+01 0.75000E+01 0.10000E+02

0.10636E-01 0.51550E-02 0.00000E+00 0.10636E-01 0.51550E-02 0.00000E+00 0.10636E-01 0.51550E-02 0.00000E+00

0.26574E-02 0.24775E-02 0.23526E-02 0.18791E-02 0.17518E-02 0.16635E-02 0.00000E+00 0.00000E+00 0.00000E+00

0.00000E+00 0.00000E+00 0.00000E+00 0.18791E-02 0.17518E-02 0.16635E-02 0.26574E-02 0.24775E-02 0.23526E-02

x-coord.

y-coord.

0.5335E+01

0.2210E+01

0.7469E+01

0.3094E+01

0.2210E+01

0.5335E+01

0.3094E+01

0.7469E+01

PROPRIETARY MATERIAL.

sigma-x sigma-xz 0.1117E+03 -0.3641E+01 0.7314E+02 -0.2600E+01 0.4530E+03 -0.1508E+01 0.3036E+03 -0.1077E+01

sigma-y sigma-yz

sigma-xy

0.4530E+03 -0.1508E+01 0.3036E+03 -0.1077E+01 0.1117E+03 -0.3641E+01 0.7314E+02 -0.2600E+01

-0.1707E+03

c The McGraw-Hill Companies, Inc. °

-0.1152E+03 -0.1707E+03 -0.1152E+03

All rights reserved.

397

SOLUTIONS MANUAL

Problem 13.78: Analyze the plate problem in Fig. P12.2 for its transient response. Use a mesh of 2 × 4 CPT(N) elements and E = 107 psi, ν = 0.25, ρ = 1 lb/in3 , h = 0.25 in., q0 = 10 lb/in., ∆t = 0.05 and α = γ = 0.5. Solution: The input data and partial output are included in Box 13.78. Plot of w(5, 10, t) = w15 (t) versus t is presented in the figure. Box 13.78: Input data file for the transient analysis of the plate problem of Fig. P12.2 (using the CPT(N) element). Problem 13.78: Bending of a cantilever plate--CPT(N) 4 1 2 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 1 0 IEL, NPE, MESH, NPRNT 2 4 NX, NY 0.0 2.5 2.5 X0, DX(I) 0.0 2.5 2.5 2.5 2.5 Y0, DY(I) 9 NSPV 1 1 1 2 1 3 2 1 2 2 2 3 3 1 3 2 3 3 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 3 NSSV 13 1 14 1 15 1 ISSV(I,J) 12.5 25.0 12.5 VSSV(I) 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,ANU12,G12,... 0.0 0.0 0.0 F0, FX, FY 1.0 0.0 0.0 C0, CX, CY 50 51 1 0 NTIME,NSTP,INTVL,INTIAL 0.05 0.5 0.5 1.0E-5 DT,ALFA,GAMA,EPSLN

0.500

Deflection, w

0.375

∂w ∂w = =w=0 ∂x ∂x 7 4 1

0.250

Deflection at this point is plotted as a function of t 10

2

13

14

0.125

3

x

6

9

12

0.000 0.00

0.50

1.00

1.50

2.00

2.50

Time, t

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

³ 15

y

398

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 13.80: Determine the transient response of the annular plate in Fig. P12.5 using four SDT elements, ∆t = 0.05, ρ = 1.0 and α = γ = 0.5. Plot the deflection at node 1 as a function of time for at least two periods. Solution: The input data and partial output are included in Box 13.80. Plot of w(5, 0, t) versus t is presented in the figure. Box 13.80: Input data file for the transient analysis of annular plate problem of Fig. P12.5. Prob 13.80: Transient analysis of an annular plate (SDT) 3 1 2 0 ITYPE,IGRAD,ITEM,NEIGN 1 4 0 0 IELTYP,NPE,MESH,NPRNT 4 9 NEM, NNM 1 2 5 4 2 3 6 5 4 5 8 7 5 6 9 8 NOD(I,J) 5.0 0.0 7.5 0.0 10.0 0.0 3.5355 3.5355 5.3033 5.3033 7.07107 7.07107 0.0 5.0 0.0 7.5 0.0 10.0 GLXY(I,J) 9 NSPV 1 3 2 3 3 1 3 3 6 1 7 2 8 2 9 1 9 2 ISPV(I,J) 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 VSPV(I) 3 NSSV 1 1 4 1 7 1 ISSV 1.9635 3.927 1.9635 VSSV 1.0E7 1.0E7 0.25 0.4E7 0.4E7 0.4E7 0.25 E1,E2,... 0.0 0.0 0.0 F0, FX, FY 1.0 0.0 0.0 C0, CX, CY 50 51 1 0 NTIME,NSTP,INTVL,INTIAL 0.05 0.5 0.5 1.0E-5 DT,ALFA,GAMA,EPSLN

0.03

Deflection, w

0.02

0.02

0.01

0.01

0.00 0.00

0.20

0.40

0.60

0.80

1.00

Time, t PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

399

Chapter 14 PRELUDE TO ADVANCED TOPICS

Problem 14.1: Consider the second-order equation µ

du d a − dx dx

¶

=f

(1)

and rewrite it as a pair of first-order equations −

du P + = 0, dx a

−

dP −f =0 dx

(2)

Construct the weighted-residual finite element model of the equations, and specialize it to the Galerkin model. Assume interpolation in the form u=

m X

uj ψi (x),

P =

j=1

n X

Pj φj (x)

(3)

j=1

and use the equations in (2) in a sequence that yields symmetric element equations: ∙

[K 11 ] [K 12 ]T

[K 12 ] [K 22 ]

¸½

{u} {P }

¾

=

½

{F 1 } {F 2 }

¾

(iv)

The model can also be called a mixed model because (u, P ) are of different kinds. Solution: The element coefficients are 11 21 12 12 = 0, Kij = Kji , Kij = Kij 22 Kij =

Fi1

=

1 EI

Z xb xa

Z xb xa

Z xb dψi dψj xa

dx dx

dx

ψi ψj dx, Fi2 = P1 ψi (xa ) + P2 ψi (xb )

f ψi dx + Q1 ψi (xa ) + Q2 ψi (xb ) ¯

¯

¯

¯

dM ¯¯ dM ¯¯ dw ¯ dw ¯¯ , Q2 = , P1 = − ¯¯ , P2 = Q1 = − ¯ ¯ dx x=xa dx x=xb dx x=xa dx ¯x=xb PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

400

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Problem 14.2: Evaluate the coefficient matrices [K αβ ] in Problem 14.1 for a = constant and column vectors {F α } for f = constant. Assume that ψi = φi are the linear interpolation functions. Eliminate {P } from the two sets of equations (iv) to obtain an equation of the form [K]{u} = {F } Compare the coefficient matrix [K] and vector {F } with those obtained with the weak form finite element model of (a). What conclusions can you draw? Solution: The finite-element equations associated with Eq. (b) of Problem 14.1 are given by ∙ ¸½ e¾ ½ ¾ ½ e¾ 1 fe he 1 1 −1 P1 Q1 = + e −1 1 1 P Qe2 2 2 2 ∙

1 −1 1 2 −1 1

¸½ e ¾ u 1 ue2

∙

he 2 1 = 6ae 1 2

¸½

P1e P2e

¾

Problem 14.3: Develop the least-squares finite element model of (2) in Problem 14.1, and compute element coefficient matrices and vectors when ψi = φi are the linear interpolation functions. Solution: The least-squares functional of the two equations in (2) is I=

Z xb "µ du

P + − dx a

xa

¶2

µ

dP +f + dx

¶2 #

dx

Setting δu I = 0 and δP I = 0, we obtain the integral statements µ Z xb ∙ dδu du

¶¸

P δu I = 2 + − − dx = 0 dx dx a xa µ ¶ µ ¶¸ Z xb ∙ δP du P dδP dP + + f dx = 0 − + δP I = 2 a dx a dx dx xa

(1) (2)

Substituting the approximations u=

m X

uj ψi (x),

P =

j=1

n X

Pj φj (x)

(3)

j=1

into Eqs. (1) and (2), we obtain the finite element model ∙

[K 11 ] [K 12 ]T

PROPRIETARY MATERIAL.

[K 12 ] [K 22 ]

¸½

{u} {P }

¾

=

½

{F 1 } {F 2 }

¾

c The McGraw-Hill Companies, Inc. °

(4) All rights reserved.

SOLUTIONS MANUAL

401

where the element coefficients are 11 Kij =

Z xb dψi dψj

dx dx dx Z xb 1 dψi 12 21 Kij φj dx = Kji =− a dx xa ¸ Z xb ∙ 1 dφi dφj 22 Kij = φi φj + dx a2 dx dx xa Z xb dφi f (x) dx Fi1 = 0, Fi2 = − xa dx xa

(5)

For the choice of linear interpolation functions for ψi and φi and elementwise constant value of a, the element coefficients in (5) are

K22

∙

1 he he = 2 6ae

K11 =

¸

∙

1 1 −1 1 1 , K12 = −1 1 2ae −1 −1 ∙ ¸ ∙ ¸ 1 2 1 1 −1 + 1 2 1 he −1

¸

(6)

Problem 14.4: Solve the problem in Example 3.2.1 using two elements of the leastsquares model developed in Problem 14.3. Compare the results with the exact solution and those of the weak form finite element model. Solution: The governing equation of Example 3.2.1 is slightly more general than Eq. (1) of Problem 14.1. Hence, we consider the more general equation µ

¶

du d a + cu = f − dx dx

(1)

and rewrite it as a pair of first-order equations −

du P + = 0, dx a

−

dP + cu − f = 0 dx

(2)

The least-squares functional becomes I=

Z xb "µ du xa

P + − dx a

¶2

µ

dP + cu − f + − dx

¶2 #

dx

Setting δu I = 0 and δP I = 0, we obtain the integral statements µ Z xb ∙ dδu du

¶

µ

¶¸

P dP + + cu − f dx = 0 δu I = 2 − − + cδu − dx dx a dx xa ∙ µ ¶ µ ¶¸ Z xb δP du P dδP dP + + cu − f dx = 0 − − − δP I = 2 a dx a dx dx xa PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(3) (4)

402

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

For this more general case, the finite element model (4) of Problem 14.3 is still valid with 11 Kij

=

Z xb µ dψi dψj

dx dx

xa

12 =− Kij 22 Kij =

Fi1 =

Z xb µ 1 dψi xa

Z xb ∙ 1 xa

Z xb xa

a

a dx

2

+ c ψi ψj φj + cψi

φφ + 2 i j

¶

dφj dx ¸

dx ¶

21 dx = Kji

dφi dφj dx dx dx

cψi f (x) dx, Fi2 = −

Z xb dφi

dx

xa

f (x) dx

(5)

For the choice of linear interpolation functions for ψi and φi and elementwise constant values of a, c and f , the element coefficients in (5) are 11

K

K12 K22

∙

¸

∙

¸

1 c2 he 2 1 1 −1 = + e 1 1 2 he −1 6 ∙ ¸ ∙ ¸ 1 ce 1 −1 1 1 = + 2ae −1 −1 2 1 −1 ∙ ¸ ∙ ¸ he 2 1 1 1 −1 = 2 + 1 6ae 1 2 he −1

(6)

For the problem in Example 3.2.1, we have a = 1, c = −1 and f (x) = −x2 . Hence, the source vector is given by Z xb

½

xb 1 4 3 3 4 1 3 (xb − xa ) − 4 (xb − xa ) =− ψi (−x ) dx → F = he − x3a (x3b − x3a ) + 14 (x4b − x4a ) xa ½ ¾ Z xb dφi x3b − x3a 1 2 2 2 (−x ) dx → F = − Fi = − −1 3he xa dx

Fi1

2

1

¾

The element equations become ⎡ 1 he he + 3 ⎢ 0 ⎢ ⎢ 1 ⎣ − h + h6e e

1

0 he 1 he + 3 −1 1 − he + h6e

− h1e + h6e −1 1 he he + 3 0

1 1 − he + h6e 0 1 he he + 3

Using h1 = h2 = 0.5, the element equations become ⎡

⎤⎧

⎫

⎤⎧ ⎫ ⎧ 1⎫ u1 ⎪ ⎪ ⎪ F1 ⎪ ⎪ ⎪ ⎬ ⎪ ⎨ 2⎪ ⎥⎨ F1 ⎬ ⎥ P1 = ⎥ u ⎪ ⎪ F1 ⎪ ⎦⎪ ⎪ ⎩ 2⎪ ⎭ ⎪ ⎩ 22 ⎪ ⎭

P2

⎧

F2

⎫

26 0 −23 12 ⎪ u1 ⎪ F11 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎨ ⎬ ⎨ 2⎬ 1 ⎢ 0 26 −12 −23 ⎥ ⎢ ⎥ P1 = F1 26 0⎦⎪ u ⎪ ⎪ F1 ⎪ 12 ⎣ −23 −12 ⎪ ⎩ 2⎪ ⎭ ⎪ ⎩ 22 ⎪ ⎭ 12 −23 0 26 P2 F2

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

403

The assembled equations of the two-element mesh is ⎤⎧

⎡

⎫

⎧

⎫

26 0 −23 12 0 0 ⎪ U1 ⎪ 1⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎢ ⎥⎪ 0 26 −12 −23 0 0 −8 U 2⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎢ ⎥⎪ ⎨ ⎬ ⎨ ⎬ ⎥ 1 ⎢ 1 −23 −12 52 0 −23 12 14 U 3 ⎢ ⎥ = 0 52 −12 −23 ⎥ −48 ⎪ U ⎪ 96 ⎪ 12 ⎢ ⎪ ⎪ ⎪ ⎢ 12 −23 ⎥⎪ ⎪ 4⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎣ ⎪ ⎪ ⎪ ⎪ 0 0 −23 −12 26 0⎦⎪ U ⎪ ⎪ ⎪ ⎪ ⎩ 5⎭ ⎩ 17 ⎭ 0 0 12 −23 0 26 56 U6

Using the boundary conditions U1 = U5 = 0, we obtain the condensed equations ⎤⎧

⎡

⎫

⎧

⎫

26 −12 −23 0 ⎪ −1.00 ⎪ ⎪ ⎪ U2 ⎪ ⎪ ⎪ ⎪ ⎨ ⎥ ⎨ U3 ⎬ 1 ⎢ 1 −12 52 0 12 1.75 ⎬ ⎢ ⎥ = 0 52 −23 ⎦ ⎪ −6.00 ⎪ U ⎪ 12 ⎪ 12 ⎣ −23 ⎪ ⎪ ⎪ ⎩ 4⎪ ⎭ ⎩ ⎭ 0 12 −23 26 7.00 U6

whose solution is

U2 = −0.11453,

U3 = −0.04746,

U4 = −0.06122,

U6 = 0.23698

The two-element weak form solution for U3 is U3 = −0.03977. The exact value is u(0.5) = 0.04076. Problem 14.5: Show that the mixed finite element model of the Euler—Bernoulli beam theory, (14.2.47a), is the same as that in Eq. (5.2.18) for the choice of linear interpolation of w and M . Solution: For linear interpolation of w and M and element-wise constant values of EI, the element matrices in (14.2.47a) become ∙

¸

∙

¸

⎤⎧

⎫

½

¾

1 he 1 −1 2 1 f1e , [Ge ] = , {f e } = 1 f2e he −1 6Ee Ie 1 2 ∙ ¸ ∙ ¸ 2Ee Ie 6Ee Ie 2 −1 1 −1 [Ge ]−1 = , [Ge ]−1 [K e ]T = −1 2 −1 1 he h2e ∙ ¸ ³ ´ 12Ee Ie 1 −1 e −1 e T e e −1 T [K e ][Ge ]−1 [K e ]T = , [G ] [K ] = [K ][G ] −1 1 h3e [K e ] =

Hence, we have from Eq. (14.2.47a) the result ⎡

6 2Ee Ie ⎢ −3h e ⎢ h3e ⎣ −6 −3he

−3he 2h2e 3he h2e

−6 3he 6 3he

⎧

⎫

⎧

⎫

−3he ⎪ w1e ⎪ q1e ⎪ Qe1 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎨ ⎬ ⎨ ⎬ ⎨ 2 e he ⎥ 0 Qe2 ⎬ ⎥ Θ1 = + ⎪ ⎪ q2e ⎪ 3he ⎦ ⎪ w2e ⎪ Qe3 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎩ ⎭ ⎩ ⎭ ⎩ ⎭ 2h2e Θe2 0 Qe4

Interestingly, the stiffness matrix of the mixed finite element model with linear interpolation of both w and M is the same as that of the displacement finite element PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

404

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

model derived in Chapter 5 using the C 1 (Hermite cubic) interpolation. However, the load vector differs in the sense that the mixed model does not contain contributions of distributed load q(x) to the nodal moment components. Problem 14.6: Consider the pair of equations ∇u − q/k = 0,

∇ · q + f = 0 in Ω

where u and q are the dependent variables, and k and f are given functions of position (x, y) in a two-dimensional domain Ω. Derive the finite element formulation of the equations in the form ⎡

⎫

⎤⎧

[K 11 ]

⎧

⎫

[K 12 ] [K 13 ] ⎨ {u} ⎬ ⎨ {F 1 } ⎬ ⎣ [K 22 ] [K 23 ] ⎦ {q1 } = {F 2 } ⎭ ⎩ 2 ⎭ ⎩ symmetric [K 33 ] {q } {F 3 }

Caution: Do not eliminate the variable u from the given equations. Solution: The weak form is 0= 0=

Z Z

Ωe

(gradw · q − wf) dxdy − µ

¶

Z

Γe

wqn ds = 0

1 v · gradu − q dxdy = 0 k Ωe

where v = (v1 , v2 ) and w are test functions (or, variations in q and u, respectively), ˆ · q. and qn = n For the case when u, q1 , q2 are interpolated by same ψi , we have 11 12 Kij = 0, Kij = 21 12 22 = Kji , Kij Kij 31 13 32 Kij = Kji , Kij

Fi1 =

Z

Γe

Z

Z

∂ψi ∂ψi 13 ψj dxdy, Kij ψj dxdy = Ωe ∂x Ωe ∂y Z 1 23 ψi ψj dxdy, Kij =− =0 Ωe k 33 22 = 0, Kij = Kij

ψi qn ds, Fi2 = 0, Fie = 0

Problem 14.7: Compute the element coefficient matrices [K αβ ] and vectors {F α } of Problem 14.6 using linear triangular elements for all variables. Assume that k is a constant. Solution: The matrices Kαβ can be expressed in terms of Sαβ introduced in Eq. (8.2.39). We have K12 = S10 , PROPRIETARY MATERIAL.

K13 = S20 ,

1 K22 = − S00 k

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

405

αβ where Sij are given in Eq. (8.2.44) for a linear triangular element.

Problem 14.8: Repeat Problem 14.7 with linear rectangular elements. Solution: The matrices Kαβ can be expressed in terms of Sαβ introduced in Eq. (8.2.39). We have K12 = S10 ,

K13 = S20 ,

1 K22 = − S00 k

αβ where Sij are given in Eq. (8.2.52) for a linear rectangular element, except that 10 01 T S = (S ) and S20 = (S02 )T are given in the solution to Problem 8.10.

Problem 14.9: Consider the following form of the governing equations of the classical plate theory: −(

∂ 4w ∂ 2 Myy ∂ 2 Mxx − 4D + )=q 66 ∂x2 ∂x2 ∂y 2 ∂y 2 ¡ ¢ ∂2w ¯ 12 Myy , ¯ 22 Mxx + D =− D 2 ∂x ¡ ¢ ∂2w ¯ 11 Myy ¯ 12 Mxx + D =− D 2 ∂y

(a)

(b)

where Mxx and Myy are the bending moments, w is the transverse deflection, q is the distributed load, ν is the Poisson ratio, and ¯ ij = Dij , D D0

2 D0 = D11 D22 − D12

(a) Gove the weak form of the equations, and (b) assume approximation of the form

w=

4 X

wi ψi1 ,

i=1

Mxx =

2 X

Mxi ψi2 ,

Myy =

i=1

2 X

Myi ψj3

i=1

to develop the (mixed) finite element model in the form ⎡

[K 11 ]

⎤⎧

⎫

⎧

⎫

[K 12 ] [K 13 ] ⎨ {w} ⎬ ⎨ {F 1 } ⎬ ⎣ [K 22 ] [K 23 ] ⎦ {Mxx } = {F 2 } ⎭ ⎩ ⎭ ⎩ symm. [K 33 ] {Myy } {F 3 }

Comment on the choice of the functions ψiα for α = 1, 2, 3. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

406

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Solution: The weak forms of Eqs. (a) and (b) over a typical element Ωe are 0=

Z

Ωe

I

Ã

!

∂δw ∂Mxx ∂δw ∂Myy ∂ 2 δw ∂ 2 w + + 4D66 − qδw dxdy ∂x ∂x ∂y ∂y ∂x∂y ∂x∂y

"

#

2 ¯ n − 2D66 ∂ w (δθx ny + δθy nx ) ds δwQ − ∂x∂y Γe ¸ Z ∙ ¡ ¢ ∂w ∂δMxx ¯ 12 Myy dxdy ¯ 22 Mxx − D 0= − δMxx D ∂x Ωe ∂x

−

0=

Z

I

Γe

Ωe

−

I

∙

(c)

δMxx θx nx ds

(d)

¸

¡ ¢ ∂w ∂δMyy ¯ 12 Mxx dxdy ¯ 11 Myy − D − δMyy D ∂y ∂y

Γe

δMyy θy ny ds

(e)

The primary and secondary variables of the formulation are w, Mxx , Myy , ∂w ∂w nx , θy ny ≡ ny , θx nx ≡ ∂x ∂y

Vn ,

(f ) (g)

where Vn is the effective shear force (Kirchhoff free edge condition) Vn = Qn +

∂Mns , ∂s

Qn = Qx nx + Qy ny

(h)

The finite element model of Eq. (d) and (e) is obtained by substituting the approximations of the form w=

r X

(1)

wi ψi , Mxx =

i=1

s X

(2)

Mxi ψi , Myy =

i=1

p X

(3)

Myi ψi

(i)

i=1

(α)

where ψi , (α = 1, 2, 3, 4) are appropriate interpolation functions. We obtain ⎡

where

⎤⎧

[K 11 ]

⎫

⎧

⎫

[K 12 ] [K 13 ] ⎨ {w} ⎬ ⎨ {F 1 } ⎬ ⎣ [K 22 ] [K 23 ] ⎦ {Mx } = {F 2 } ⎭ ⎩ ⎭ ⎩ symm. [K 33 ] {My } {F 3 } 11 Kij = 4D66

Z

Ωe

∂ 2 ψi1 ∂ 2 ψi1 dxdy, ∂x∂y ∂x∂y

PROPRIETARY MATERIAL.

i, j = 1, 2, . . . , r,

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(j)

407

SOLUTIONS MANUAL

12 Kij

=

Z

∂ψi1 ∂ψj2 dxdy, ∂x ∂x ∂ψi1 ∂ψj3 dxdy, ∂y ∂y

Ωe

13 Kij = 22 Kij = 23 Kij = 33 = Kij

Fi1 = Fi2 = Fi3 =

Z

Ωe

Z

Ωe

Z

Ωe

Z

Ωe

i, j = 1, 2, . . . , s,

¯ 12 )ψi2 ψj3 dxdy, (−D

i = 1, 2, . . . , s;

¯ 11 )ψi3 ψj3 dxdy, (−D

i, j = 1, 2, . . . , p,

qψi1 dxdy +

Ωe Γe

I

Γe

i, j = 1, 2, . . . , r; j = 1, 2, . . . , p,

¯ 22 )ψi2 ψj2 dxdy, (−D

Z I

i, j = 1, 2, . . . , r; j = 1, 2, . . . , s,

I

Γe

Vn ψi1 ds,

j = 1, 2, . . . , p,

i = 1, 2, . . . , r,

θx nx ψi2 ds,

i = 1, 2, . . . , s,

θy ny ψi3 ds,

i = 1, 2, . . . , p,

(k)

An examination of the weak forms (d) and (e) show that the minimum continuity conditions of the interpolation functions ψiα (α = 1, 2, 3) are ψi1 = linear in x and linear in y ψi2 = linear in x and constant in y

(i)

ψi3 = linear in y and constant in x ψi4 = linear in x and linear in y Problem 14.10: Use the interpolation w=

4 X

wi ψi1 ,

Mxx =

i=1

2 X

Mxi ψi2 ,

Myy =

i=1

2 X

Myi ψj3

i=1

with ψ11

µ

x = 1− a

¶µ

¶

µ

¶

µ

y x y xy x 1− , ψ21 = 1− , ψ31 = , ψ41 = 1 − b a b ab a

ψ12 = 1 −

x , a

φ22 =

x , a

y ψ13 = 1 − , b

ψ23 =

¶

y b

y b

for a rectangular element with sides a and b to evaluate the matrices [K αβ ](α, β = 1, 2, 3) in Problem 14.9. PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

408

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Solution: We can select either ψ12 = 1 −

x x , ψ22 = , a a

y y ψ13 = 1 − , ψ23 = b b

(a)

and ψi1 to be the bilinear interpolation functions, or ψi1 = ψi2 = ψi3 = ψi4 = bilinear functions of a rectangular element

(b)

The corresponding rectangular elements are shown in Figure P14.10. My2 3

4 w0 , Mx , My at each node 1

2

3 7 w0 , Mx , My 8 at each node 6

4

1

5

3

4 w0 at four corner nodes

Mx1 1

2

Mx2 2

My1

(a) Mixed model A

(b) Mixed model B

(c) Mixed model C

Figure P14.10: Mixed rectangular plate bending elements based on CPT. (a) Model A. (b) Model B. (c) Model C. The numerical form of element matrices is ⎡

⎤

⎡

⎤

1 −1 1 −1 1 −1 ⎥ ⎢ −1 4D66 ⎢ b −1 1 −1 1 1⎥ 11 12 ⎢ ⎥ , [K ] = ⎢ ⎥ = [K 21 ]T [K ] = ⎣ ⎦ ⎣ 1 −1 1 −1 1⎦ ab 2a −1 −1 1 −1 1 1 −1 ⎡ ⎤ 1 −1 ∙ ¸ ⎢ a D22 ab 2 1 1 −1 ⎥ 13 31 T 22 ⎢ ⎥ [K ] = [K ] = , [K ] = − 1⎦ 1 2 2b ⎣ −1 6 −1 1 ∙ ¸ D12 ab 1 1 D11 22 [K 23 ] = [K 32 ]T = , [K 33 ] = [K ] 1 1 4 D22 Problem 14.11: Repeat Problem 14.10 for the case in which φ1i = φ2i = ψi . Solution: [K 11 ] is the same as in Problem 14.10. Also, we have [K 12 ] = [K 21 ]T = [S 11 ], [K 13 ] = [K 31 ]T = [S 22 ] [K 22 ] = −D22 [S 00 ], [K 23 ] = [K 32 ]T = D12 [S 00 ], [K 33 ] = −D11 [S 00 ] PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

409

where [S 11 ], [S 22 ] and [S 00 ] are defined in Eq. (8.2.52). Problem 14.12: Evaluate the element matrices in (14.4.6b) by assuming that the nonlinear parts in the element coefficients are element-wise-constant. Solution: We have ∙

¸

∙

EA 1 EA 1 −1 1 0 −1 0 [K ] = , [K 12 ] = [K 21 ] = 1 1 0 L −1 2 L −1 0 11

⎡

⎤

⎡

¸

⎤

6 −3L −6 −3L 36 −3L −36 −3L 2 2 ⎥ ⎢ ⎢ 2EI N −3L 2L −3h 4L2 3L L 3L −L2 ⎥ ⎥+ ⎢ ⎥ [K 22 ] = 3 ⎢ 3L 6 3L ⎦ 30L ⎣ −36 3L 36 3L ⎦ L ⎣ −6 3L 2L2 −3L L2 −3L −L2 3L 4L2

where L is the length of the element and N = 0.5(dw/dx.

Problem 14.13: Give the finite element formulation of the following nonlinear equation over an element (xa , xb ) : −

µ

¶

d du u + 1 = 0 for 0 < x < 1 dx dx µ

du dx

¶¯ ¯ ¯ ¯

= 0,

u(1) =

√ 2

x=0

Solution: The weak form is same as in the linear equation except that we have a(x) = u(x): [K(¯ u)]{u} = {F } with [see Reddy (2004b)] e Kij

=

Z xb à X n

uek ψke

uek

ψke

xa

=

n X

k=1

Fi = −

Z xb xa

k=1 Z xb xa

!

dψie dψje dx dx dx

dψie dψje dx dx dx

(a)

ψie dx + Qi

For example, for linear approximation (n = 2) of u(x), we have e Kij

= =

n X

k=1 n X

uek

Z xb xa

ψke

dψie dψje dx dx dx

ae0 uek (−1)i+j

k=1 e i+j a0

= (−1)

2he

PROPRIETARY MATERIAL.

1 h2e

à n X

k=1

Z xb

uek

xa

!

ψke dx

= (−1)i+j

ae0 (ue + ue2 ) 2he 1

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(b)

410

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

or

∙

ae (ue + ue2 ) 1 −1 [K ] = 0 1 −1 1 2he e

¸

(c)

Further, the assembled equations associated with a mesh of two linear elements of equal length are (U1 , U2 , U3 are the global nodal values) ⎤⎧

⎡

⎫

(U1 + U2 ) −(U1 + U2 ) 0 ⎨ U1 ⎬ 1 ⎣ −(U1 + U2 ) (U1 + 2U2 + U3 ) −(U2 + U3 ) ⎦ U2 ⎭ ⎩ 2h 0 −(U2 + U3 ) (U2 + U3 ) U3 ⎧ ⎪ ⎨

⎫

(1)

⎧

⎫

(1)

⎪ ⎪ f1 Q1 ⎬ ⎪ ⎨ ⎬ (1) (2) (1) (2) = f2 + f1 + Q2 + Q1 ⎪ ⎪ ⎪ ⎩ ⎭ ⎪ ⎩ ⎭ (2) (2) f2 Q2

(d)

Problem 14.14: Compute the tangent coefficient matrix for the nonlinear problems in Problem 14.13. What restriction(s) should be placed on the initial guess vector? Solution: By definition (14.4.17), we have [see Reddy (2004b)] (KTe )ij

∂Rie ∂ ≡ = e ∂uj ∂uej =

n X

m=1

Ã

à n X

e Kim uem

− Fie

m=1 ! e e ∂Kim e ∂u m e u + Kim ∂uej m ∂uej

!

=

n e X ∂Kim e e e um + Kij

m=1

∂uj

(a)

For the problem at hand, we have (KT )ij =

n e X ∂Kim e e e um + Kij

m=1 n X

∂uj

∂ = ∂uej m=1

µZ x b xa

¶

e dψ e dψm e uh i dx uem + Kij dx dx

à n ! Z xb e ∂uh dψie X dψ m = ue dx + K e xa

∂uej dx

m

m=1

ij

dx

Z xb duh dψie e e e e ˆ ij = ≡K + Kij ψj dx + Kij xa

where the identity

dx dx n X

m=1

uem

duh dLem = dx dx

is used in arriving at the last line. We have, e ˆ ij K =

Z xb Z duh dψie e ue − ue1 xb dψie e ψj dx = 2 ψj dx xa

dx dx

PROPRIETARY MATERIAL.

2

xa

dx

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(i)

SOLUTIONS MANUAL

or

∙

e e ˆ e = u2 − u1 −1 −1 K 1 1 2he Thus, the tangent matrix becomes

KeT

∙

¸

¸

∙

¯e2 ) ¯e1 ) −1 −1 ue1 + u (¯ ue − u 1 −1 ˆ e = (¯ =K +K + 2 −1 1 1 1 2he 2he e

411

¸

where u ¯ei denote the nodal values known from the previous iteration. Note that the tangent coefficient matrix is not symmetric. Also, the initial guess should not be that all Ui = 0. Since the boundary condition at x = 1 is nonzero, the initial guess should be one that satisfies the boundary condition. If the boundary condition is homogeneous, then at least one of the nodal values should be nonzero so that the tangent coefficient matrix is non-zero. Problem 14.15: Compute the tangent stiffness matrix KT in (14.4.17) for the Euler— Bernoulli beam element in (14.4.6a). Solution: The coefficients of the element tangent stiffness matrix KeT ≡ Te can be computed using the definition in (14.4.17). In terms of the components defined in Eq. (14.4.6a), we can write [see Reddy (2004b)] ⎛

⎞(r−1)

∂Riα ⎠ ⎝

Tijαβ =

∂∆βj

(a)

for α, β = 1, 2. The components of the residual vector can be expressed as Riα =

2 X X

γ=1 p=1

=

2 X

αγ γ Kip ∆p − Fiα

α1 1 Kip ∆p +

p=1

=

2 X

4 X

P =1 α1 Kip up +

p=1

4 X

P =1

α2 2 KiP ∆P − Fiα

α2 ¯ KiP ∆P − Fiα

(b)

Note that the range of p is dictated by the size of the matrix [K αβ ]. We have Tijαβ = =

⎛

⎞

∂Riα ⎠ ⎝ ∂∆βj

2 X X

γ=1 p=1 αβ = Kij +

=

⎛

⎝K 2 X

∂∆βj

⎛ ⎝

∂∆βj ∂

∂∆βj

2 X X

γ=1 p=1

γ αγ ∂∆p

ip

p=1 PROPRIETARY MATERIAL.

∂

³

+

αγ γ Kip ∆p − Fiα ⎠

αγ ∂Kip

∂∆βj ´

⎞

⎞

∆γp ⎠

α1 Kip up +

4 X

P =1

∂ ∂∆βj

³

´

α2 ¯ KiP ∆P

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(c)

412

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

Then the tangent stiffness matrix coefficients Tijαβ can be computed as follows: 11 Tij11 = Kij +

2 11 X ∂Kip

∂uj

p=1 11 = Kij +

2 X

p=1

Since

up +

4 12 X ∂KiP ¯P ∆

∂uj

P =1 4 X

0 · up +

P =1

¯P 0·∆

(d)

αβ ∂Kij = 0 for all α, β, i, j and k ∂uk

(e)

the coefficients [T 11 ] and [T 21 ] of the tangent stiffness matrix are the same as those of the direct stiffness matrix: [T 11 ] = [K 11 ] , [T 21 ] = [K 21 ]

(f )

Next consider 12 TiJ

=

12 KiJ

+

2 X

p=1

Ã

11 ∂Kip ¯J ∂∆

P =1

12 = KiJ +

12 + = KiJ

22 TIJ

=

12 KiJ

=

22 KIJ

P =1 xa "Z 4 xb X xa

xa

2 X

p=1 22 = KIJ +

µ

à 4 X K

dw dx

!

¶

¯P ∆ #

dψi dφP ¯P dx ∆ dx dx

¯ K dφK ∆ dx #

!

#

dψi dφP ¯P dx ∆ dx dx

¶

à 4 ! X dφP ¯ P dx ∆ P =1

dx

dw dψi dφJ dx 2 dx dx dx 12 21 = 2KiJ = KJi

Ã

Axx

21 ∂KIp ¯J ∂∆

" 2 Z xb X

p=1

12 ∂KiP ¯J ∂∆

1 dφJ dψi dφP ¯P Axx dx ∆ 2 dx dx dx

dψi dφJ Axx 2 dx dx

Z xb µ 1

Ã

∂ Axx ¯ 2 ∂ ∆J

∂ Axx ¯ 2 ∂ ∆J

Z xb 1

xa 12 + KiJ

+

P =1

"Z 4 xb 1 X

P =1 12 = KiJ +

xa

4 X

up +

"Z 4 xb 1 X

12 = KiJ +0+

12 = KiJ +

!

xa

PROPRIETARY MATERIAL.

!

up +

∂ Axx ¯ ∂ ∆J

4 X

P =1

à 4 X K

Ã

22 ∂KIP ¯J ∂∆

(g) !

¯ K dφK ∆ dx

!

¯P ∆ #

dφI dψp dx up dx dx

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

+

"Z 4 xb 1 X

P =1

22 = KIJ +

+

Z xb xa

=

22 KIJ

+

∂ Axx ¯ 2 ∂ ∆J

xa

Z xb xa

Axx

xa

dw dx ⎛

¶2

#

dφI dφP ¯P dx ∆ dx dx ⎞

2 dφI dφJ ⎝X dψp ⎠ up dx Axx dx dx p=1 dx

µ

Z xb

µ

413

dw dx

Axx

¶

µ

dφI dφJ dx dx

à 4 X

¯ P dφP ∆ dx P =1

du0 dw dw + dx dx dx

¶

!

dx

dφI dφJ dx dx dx

(h)

Problem 14.16: Develop the nonlinear finite element model of the Timoshenko beam theory. Equations (14.56) are valid for this case, with the following changes. In place of (d2 /dx2 )(b d2 w/dx2 ) use −(d/dx)(b dΨ/dx) + GAk(dw/dx + Ψ) and add the following additional equation for w: −

∙

µ

¶¸

d dw +Ψ GAk dx dx

=q

See Section 4.4 for additional details. Solution: The equations of equilibrium of the Timoshenko beam theory for the nonlinear case are d − dx

(

du 1 + dx 2

µ

dw dx

¶2 #)

=f

(a)

dw d +Ψ Sxx − dx dx ( " µ ¶ #) dw du 1 dw 2 d + − Axx =q dx dx dx 2 dx µ ¶ µ ¶ dΨ dw d +Ψ =0 Dxx + Sxx − dx dx dx

(b)

∙

Axx

"

µ

¶¸

(c)

where Axx = EA, Sxx = Ks GA and Dxx = EI. The weaks forms of the three equations are 0=

Z xb ( xa

"

dδu du 1 + Axx dx dx 2

µ

dw dx

− Qe1 δu(xa ) − Qe4 δu(xb )

¶2 #

)

+ f δu0 dx

( " ) µ ¶ µ ¶ # Z xb 1 dw 2 dδw dw e e dw du 0= + Ψ + Axx + Sxx δwq dx xa

dx

dx

PROPRIETARY MATERIAL.

dx dx

2

dx

c The McGraw-Hill Companies, Inc. °

All rights reserved.

(d)

414

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

− Qe2 δw(xa ) − Qe5 δw(xb ) µ ¶¸ dw e dδΨ dΨ e + Sxx δΨ + Ψ dx Dxx 0= dx dx dx xa − Qe3 δΨ(xa ) − Qe6 δΨ(xb )

(e)

Z xb ∙

(f )

where δu, δw, and δΨ are the virtual displacements. The Qei have the same physical meaning as in the Euler—Bernoulli beam element, and their relationship to the horizontal displacement u, transverse deflection w0 , and rotation Ψ, is Qe1 = −Nxx (xa ),

Qe4 = Nxx (xb ) ¸ ∙ ¸ dw dw e e , Q5 = Qx + Nxx Q2 = − Qx + Nxx dx x=xa dx x=xb e e Q3 = −Mxx (xa ), Q6 = Mxx (xb ) ∙

(g)

Suppose that the displacements are approximated as u(x) =

m X

(1) uej ψj ,

w(x) =

j=1

n X

(2) wje ψj ,

Ψ(x) =

j=1

p X

(3)

sej ψj

(h)

j=1

(α)

where ψj (x) (α = 1, 2, 3) are Lagrange interpolation functions of degree (m − 1), (n − 1), and (p − 1), respectively. At the moment, the values of m, n, and p are arbitrary, that is, arbitrary degree of polynomial approximations of u0 , w0 , and Ψ (1) (2) may be used. Substitution of (h) for u, w, and Ψ, and δu = ψi , δw = ψi , and (3) δΨ = ψi into Eqs. (d)—(f) yields the finite element model 0= 0= 0=

m X

j=1 m X j=1 m X

11 e Kij uj +

21 e Kij uj +

31 e Kij uj +

j=1

n X

j=1 n X j=1 n X

12 e Kij wj +

22 e Kij wj +

32 e Kij wj +

j=1

p X

j=1 p X j=1 p X j=1

13 e Kij sj − Fi1

(i)

23 e Kij sj − Fi2

(j)

33 e Kij sj − Fi3

(k)

where 11 Kij = 21 Kij

=

Z xb xa

Z xb xa

(1)

Axx

(1) dψi dψj dx dx

12 dx, Kij = (1)

(2) dw0 dψi dψj Axx dx dx dx

PROPRIETARY MATERIAL.

dx,

1 2

Z xb xa

(2)

Axx

13 Kij = 0,

(1) dw0 dψi dψj dx dx dx

dx

31 Kij =0

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

22 Kij = 23 Kij = 33 Kij =

Fi1 =

Z xb xa

Z xb xa

Z xb xa

Z xb x

Z xa b

(2)

Sxx

(2) dψi dψj dx dx

Sxx

dψi dx

(2)

⎛

dx +

(3)

ψj

Z xb xa

Axx

µ

dw0 dx

¶2

(2)

(2) dψi dψj dx dx

dx

32 dx = Kji

⎞

(3)

(3) dψ dψj (3) (3) ⎝Dxx i + Sxx ψi ψj ⎠ dx dx dx (1)

(1)

(1)

(2)

(2)

(2)

ψi f dx + Qe1 ψi (xa ) + Qe4 ψi (xb )

Fi2

=

Fi3

= Qe3 ψi (xa ) + Qe6 ψi (xb )

xa

1 2

415

ψi q dx + Qe2 ψi (xa ) + Qe5 ψi (xb ) (3)

(3)

(`)

The element equations (i)—(k) can be expressed in matrix form as ⎫

⎤⎧

⎡

⎧

⎫

[K 11 ] [K 12 ] [K 13 ] ⎨ {u} ⎬ ⎨ {F 1 } ⎬ ⎣ [K 21 ] [K 22 ] [K 23 ] ⎦ {w} = {F 2 } ⎭ ⎩ ⎭ ⎩ [K 31 ] [K 32 ] [K 33 ] {F 3 } {s}

(m)

(α)

The choice of the approximation functions ψi dictates different finite element (1) (2) models. The choice of linear polynomials ψi = ψi is known to yield a stiffness matrix that is nearly singular. This will be discussed further in the next section. (1) (2) When ψi are quadratic and ψi are linear, the stiffness matrix is 5 × 5. It is possible to eliminate the interior degree of freedom for w0 and obtain 4 × 4 stiffness (1) (2) matrix. This element behaves well. When ψi are cubic and ψi are quadratic, the stiffness matrix is 7 × 7. If the interior nodal degrees of freedom are eliminated, one obtains 4 × 4 stiffness matrix that is known to yield the exact solution at the nodes in the linear case when the shear stiffness and bending stiffnesses are element-wise constant. More details of various Timoshenko beam elements can be found in Reddy (2004b) Problem 14.17: Compute the tangent stiffness matrix for the Timoshenko beam element in Problem 14.16. Solution: The tangent matrix coefficients are defined by (see Problem 14.15) αβ Tijαβ = Kij +

3 X n X

∂

β γ=1 k=1 ∂∆j

¡ αγ ¢

Kik ∆γk

(a)

In particular, we have 11 +0 Tij11 = Kij PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

416

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

1 2 =0

12 Tij12 = Kij +

Tij13 Tij21 Tij22

= = =

13 Kij 21 Kij 22 Kij

Z xb xa

(2)

Axx

21 + 0 = Kij

+

Z xb xa

Axx

"

(1) dw0 dψi dψj 12 dx = 2Kij dx dx dx

µ

du0 dw0 + dx dx

¶2 #

(2)

(2) dψi dψj dx dx dx

23 23 Tij23 = Kij + 0 = Kij 31 31 Tij31 = Kij + 0 = Kij 32 32 Tij32 = Kij + 0 = Kij 33 33 Tij33 = Kij + 0 = Kij

(b)

αβ where the direct stiffness coefficients Kij are defined by Eq. (`) of Problem 14.16.

Problem 14.18: (Natural convection in flow between heated vertical plates) Consider the flow of a viscous incompressible fluid in the presence of a temperature gradient between two stationary long vertical plates. Assuming zero pressure gradient between the plates, we can write vx = vx (y), vy = 0, T = T (y), and d2 vx 0 = ρβg(T − Tm ) + µ 2 , dy

µ

dvx d2 T 0=k 2 +µ dy dy

¶2

where Tm = 12 (T0 + T1 ) is the mean temperature of the two plates, g the gravitational acceleration, ρ the density, β the coefficient of thermal expansion, µ the viscosity, and k the thermal conductivity of the fluid. Give a finite element formulation of the equations and discuss the solution strategy for the computational scheme. Solution: The finite element model is given by Kv vy − GT = F1 , KT T = F2

(a, b)

where v Kij =

Z yb

dψi dψj T dy, Kij = dy dy

Z yb dψi dψj

ya

Z yb ya

µ

µ

dvx dy

¶2

k

dy, Gij =

Z yb

ρgβψi ψj dy dy dy ya µ ¶ µ ¶ Z yb dvx dvx Fi1 = − ρβgψi dy + Pi , P1 = −µ , P2 = µ dy ya dy yb ya

Fi2 =

µ

ya

ψi dy + Qi , Q1 = −k

µ

dT dy

¶

, Q2 = k

ya

µ

dT dy

(c)

¶

yb

Solution strategy: Solve the assembled equations corresponding to Eq. (b) for T , subject to boundary conditions and initial values of vx = 0. Use the temperatures PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

417

thus obtained in the assembled equations associated with Eq. (a) and solve for vx . Then resolve Eq. (b) with the updated Fi2 (because of the newly computed vx ). Iterate the procedure until vx and T obtained in two consecutive iterations differ by, say, one percent. Problem 14.19: Derive the interpolation functions ψ1 , ψ5 , and ψ8 for the eight-node prism element using the alternative procedure described in Section 8.2 for rectangular elements. Solution: This is straightforward. Since ψ1 (ξ, η, ζ) must vanish on the faces ξ = 1, η = 1 and ζ = 1, it is of the form (see Fig. 14.3.2) ψ1 = c1 (1 − ξ)(1 − η)(1 − ζ),

ψ1 (−1, −1, −1) = 1 → c1 =

1 8

Similarly, we obtain 1 ψ1 = (1 − ξ)(1 − η)(1 − ζ) 8 1 ψ5 = (1 − ξ)(1 − η)(1 + ζ) 8 1 ψ8 = (1 − ξ)(1 + η)(1 + ζ) 8 e over Problem 14.20: Evaluate the source vector components fie and coefficients Kij a master prism element when f is a constant, f0 , and k1 = k2 = k3 = constant in (14.3.5b).

Solution: For a cube of sides a × b × c, the coordinate transformation become x=

b y = (1 + η), 2

a (1 + ξ), 2

c x = (1 + ζ) 2

z a

ζ

•

•

( −1, − 1, 1) •5

•

(1, − 1, 1)

•

8

•(−1, 1, 1)

(1, 1, 1) 7•

•6

η

( −1,−1,−1)

ξ

c

• • x

b

• •

PROPRIETARY MATERIAL.

y (1,−1,−1)

•( −1, 1,−1)

•1 •

2

c The McGraw-Hill Companies, Inc. °

4 3•

(1, 1,−1)

All rights reserved.

418

AN INTRODUCTION TO THE FINITE ELEMENT METHOD

and the Jacobian matrix and its inverse are ⎡

⎢ J=⎢ ⎣

∂y ∂ξ ∂y ∂η ∂y ∂ζ

∂x ∂ξ ∂x ∂η ∂x ∂ζ

∂z ∂ξ ∂z ∂η ∂z ∂ζ

⎤

⎡a 2 ⎥ ⎥=⎣0 ⎦

0

0 b 2

0

⎤

⎡

2 0 a 0 ⎦ , J−1 = ⎣ 0 c 0 2

0 2 b

0

⎤

0 0⎦ 2 c

Then the derivatives of the interpolation functions with respect to the global coordinates can be expressed in terms of the interpolation functions with respect to the natural coordinates as ⎧ ∂ψe ⎫ i ⎪ ⎪ ⎪ ⎨ ∂xe ⎪ ⎬ ∂ψi

∂y ⎪ ⎪ ⎪ ⎩ ∂ψie ⎪ ⎭

= J−1

∂z

⎧ ∂ψe ⎫ i ⎪ ⎪ ⎪ ⎨ ∂ξe ⎪ ⎬ ∂ψi

∂η ⎪ ⎪ ⎪ ⎩ ∂ψie ⎪ ⎭

=

∂ζ

e can be expressed as Hence, the coefficients Kij

e Kij

=

⎧ 2 ∂ψe ⎫ i ⎪ ⎪ ⎪ ⎨ a ∂ξe ⎪ ⎬ 2 ∂ψi

b ∂η ⎪ ⎪ ⎪ ⎩ 2 ∂ψie ⎪ ⎭ c ∂ζ

Z aZ bZ cà 0

0

0

∂ψ e ∂ψje ∂ψ e ∂ψje ∂ψ e ∂ψje + ky i + kz i kx i ∂x ∂x ∂y ∂y ∂z ∂z

!

dx

11 22 33 + ky Sij + kz Sij = kx Sij αβ where Sij are defined as

11 = Sij 22 Sij

=

33 = Sij

Z aZ bZ c ∂ψie ∂ψje 0

0

0

0

0

0

0

0

0

Z aZ bZ c Z aZ bZ c

dx dy dz ∂x ∂x ∂ψie ∂ψje dx dy dz ∂y ∂y ∂ψie ∂ψje dx dy dz ∂z ∂z

αβ The matrices Sij can now be evaluated using the Gauss quadrature:

11 = Sij 22 Sij = 33 Sij =

Z aZ bZ c ∂ψie ∂ψje 0

0

0

0

0

0

0

0

0

Z aZ bZ c Z aZ bZ c

Z Z Z bc 1 1 1 ∂ψie ∂ψje dξ dη dζ ∂x ∂x 2a −1 −1 −1 ∂ξ ∂ξ Z Z Z ac 1 1 1 ∂ψie ∂ψje ∂ψie ∂ψje dx dy dz = dξ dη dζ ∂y ∂y 2b −1 −1 −1 ∂η ∂η Z Z Z ab 1 1 1 ∂ψie ∂ψje ∂ψie ∂ψje dx dy dz = dξ dη dζ ∂z ∂z 2c −1 −1 −1 ∂ζ ∂ζ

PROPRIETARY MATERIAL.

dx dy dz =

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL

419

αβ The coefficients Sij can be evaluated using the interpolation functions listed in Eq. (14.3.31) ⎡ ⎤ 4 −4 −2 2 2 −2 −1 1 ⎢ −4 4 2 −2 −2 2 1 −1 ⎥ ⎢ ⎥ ⎢ −2 2 4 −4 −1 1 2 −2 ⎥ ⎢ ⎥ bc ⎢ 4 1 −1 −2 2⎥ ⎢ 2 −2 −4 ⎥ 11 S = ⎢ ⎥ 2 −2 −1 1 4 −4 −2 2⎥ 36a ⎢ ⎢ ⎥ ⎢ −2 2 1 −1 −4 4 2 −2 ⎥ ⎢ ⎥ ⎣ −1 1 2 −2 −2 2 4 −4 ⎦ 1 −1 −2 2 2 −2 −4 4 ⎡ ⎤ 4 2 −2 −4 2 1 −1 −2 ⎢ 2 4 −4 −2 1 2 −2 −1 ⎥ ⎢ ⎥ ⎢ −2 −4 4 2 −1 −2 2 1⎥ ⎢ ⎥ ⎢ ⎥ ac −4 −2 2 4 −2 −1 1 2 ⎢ ⎥ S22 = ⎢ ⎥ ⎢ ⎥ 2 1 −1 −2 4 2 −2 −4 36b ⎢ ⎥ ⎢ 1 2 −2 −1 2 4 −4 −2 ⎥ ⎢ ⎥ ⎣ −1 −2 2 1 −2 −4 4 2⎦ −2 −1 1 2 −4 −2 2 4 ⎡ ⎤ 4 2 1 2 −4 −2 −1 −2 ⎢ 2 4 2 1 −2 −4 −2 −1 ⎥ ⎢ ⎥ ⎢ 1 2 4 2 −1 −2 −4 −2 ⎥ ⎢ ⎥ ab ⎢ 1 2 4 −2 −1 −2 −4 ⎥ ⎢ 2 ⎥ 33 S = ⎢ ⎥ −4 −2 −1 −2 4 2 1 2⎥ 36c ⎢ ⎢ ⎥ ⎢ −2 −4 −2 −1 2 4 2 1⎥ ⎢ ⎥ ⎣ −1 −2 −4 −2 1 2 4 2⎦ −2 −1 −2 −4 2 1 2 4

Similarly, the source vector f e can be computed

Fe =

⎧ ⎫ 1⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ 1⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪1⎪ ⎪ ⎪ ⎪ ⎪ ⎪ abc ⎨ ⎬

1

1⎪ 8 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ 1 ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ ⎪ 1 ⎪ ⎪ ⎪ ⎩ ⎪ ⎭ 1

PROPRIETARY MATERIAL.

c The McGraw-Hill Companies, Inc. °

All rights reserved.

SOLUTIONS MANUAL for

An Introduction to The Finite Element Method (Third Edition) by J. N. REDDY Department of Mechanical Engineering Texas A & M University College Station, Texas 77843-3123

PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGraw-Hill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of the McGraw-Hill.

McGraw-Hill, New York, 2005